This is the second lcs driver patch containing the rest of lcs fixes.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several problems occured with lcs device driver:
- device not operational anymore after cable pull/plug-in.
- unpredictable results occured, e.g. kernel panic
using cards of type QD8F.
- STOPLAN and delete multicast address command
were not proper recognized by OSA card under heavy network workload.
- channel/device error checks missing in interrupt handler.
To fix all problems at once recovery of lcs devices has been improved.
missing error checks in lcs interrupt handler has been added.
Once a hardware problem occurs lcs will recover the device now properly.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Frank Blaschka <Frank.Blaschka@de.ibm.com>
From: Frank Pavlic <fpavlic@de.ibm.com>
- fix fake_ll during initial device bringup. fake_ll was
not active after first start of the device.
Problem only occured when qeth was built without IPV6 support.
- avoid skb usage after invocation of qeth_flush_buffers,
because skb might already be freed.
- remove yet another useless netif_wake_queue in
qeth_softsetup_ipv6 since this function is only called
when device is going online. In this case card->state will
never be in state UP. So let the net_device queue down .
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Frank Pavlic <fpavlic@de.ibm.com>
- correct checking of sscanf-%n value in qeth_string_to_ipaddr().
- don't use netif_stop_queue outside the hard_start_xmit routine.
Rather use netif_tx_disable.
- don't call qeth_netdev_init on a recovery.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In case of a parse error for the cu3088 group attribute,
return -EINVAL instead of count.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While debugging why our LCS emulator is having some problems I noticed the
following weirdness in drivers/s390/net/lcs.c routine lcs_irq. The `if'
statement is always true since SCHN_STAT_PCI is defined as 0x80.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hi,
here comes the second of the two patches ...
Frank
From: Peter Tiedemann <ptiedem@de.ibm.com>
[2/2]: remove ctctty.c and ctctty.h files .
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi jeff,
after the first shot I sent to you did not apply I
resend two new patches I've made today to remove tty from ctc network driver.
Please apply ....
Thank you ...
Frank
From: Peter Tiedemann <ptiedem@de.ibm.com>
[1/2]:
tty support code will be removed from the ctc network device driver.
Today we have a couple of alternatives which are performing much
better. The second thing is that ctc should be a network
device driver only.
We should not mix tty and networking here.
This first patch will remove the tty code from ctcmain.c .
It also removes the build entry from the Makefile as well as TTY
definitions from ctcmain.h.
The second patch will remove two files, ctctty.c and ctctty.h.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Convert all kmalloc + memset sequences in drivers/s390 to kzalloc usage.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[patch 4/6] s390: qeth :allow setting of attribute "route6" to "no_router".
From: Ursula Braun <braunu@de.ibm.com>
when setting route6 attribute back to no_router qeth does not
issue an IP ASSIST command to reset router value to no_router.
Once primary_router is set device stays in this mode.
Issue an IP ASSIST command when no_router is set in route6.
Device will be reset and thus will not longer run as a primary
router.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 5 -----
1 files changed, 5 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[patch 3/6] s390: qeth driver cleanups
From: Ursula Braun <braunu@de.ibm.com>
- code analyzing tool BEAM has found some unreachable
and unnecessary statements and also conditions
which are always true.
- removed some useless MII code since OSA card will never
allow to set such values.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 49 ++++---------------------------------------------
qeth_proc.c | 18 +++++++++---------
qeth_sys.c | 2 +-
3 files changed, 14 insertions(+), 55 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The message limit on the iucv connect call for the smsg module is too low.
Therefore increase the smsg message limit to 255.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[patch 2/2] s390: some qeth driver fixes
From: Frank Pavlic <fpavlic@de.ibm.com>
- fixed kernel panic when using EDDP support in Layer 2 mode
- NULL pointer exception in qeth_set_offline fixed.
- setting EDDP in Layer 2 mode did not set NETIF_F_(SG/TSO)
flags when device became online.
- use sscanf for parsing and converting IPv4 addresses
from string to __u8 values.
- qeth_string_to_ipaddr6 fixed. in case of double colon
the converted IPv6 address out from the string was not correct
in previous implementation.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth.h | 112 +++++++++++++++++++++++++-----------------------------------
qeth_eddp.c | 11 ++++-
qeth_main.c | 17 +++------
3 files changed, 63 insertions(+), 77 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[patch 1/2] s390: lcs performance enhancements
From: Klaus Wacker <kdwacker@de.ibm.com>
- When flood pinging (with large packet size) an LCS device,
about 90 % of all packets are dropped by driver.
- increased number of lcs IO buffers to 32.
- use netif_stop_queue/netif_wake_queue in lcs_start_xmit routine
- don't lock the whole xmit routine but just the piece of code where
tx_buffer is touched.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
lcs.c | 31 +++++++++++++++++--------------
lcs.h | 2 +-
2 files changed, 18 insertions(+), 15 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Remove all CVS generated information like e.g. revision IDs from
drivers/s390 and include/asm-s390 (none present in arch/s390).
- Add newline at end of arch/s390/lib/Makefile to avoid diff message.
Acked-by: Andreas Herrmann <aherrman@de.ibm.com>
Acked-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
