Pull networking fixes from David Miller:
1) When we run a tap on netlink sockets, we have to copy mmap'd SKBs
instead of cloning them. From Daniel Borkmann.
2) When converting classical BPF into eBPF, fix the setting of the
source reg to BPF_REG_X. From Tycho Andersen.
3) Fix igmpv3/mldv2 report parsing in the bridge multicast code, from
Linus Lussing.
4) Fix dst refcounting for ipv6 tunnels, from Martin KaFai Lau.
5) Set NLM_F_REPLACE flag properly when replacing ipv6 routes, from
Roopa Prabhu.
6) Add some new cxgb4 PCI device IDs, from Hariprasad Shenai.
7) Fix headroom tests and SKB leaks in ipv6 fragmentation code, from
Florian Westphal.
8) Check DMA mapping errors in bna driver, from Ivan Vecera.
9) Several 8139cp bug fixes (dev_kfree_skb_any in interrupt context,
misclearing of interrupt status in TX timeout handler, etc.) from
David Woodhouse.
10) In tipc, reset SKB header pointer after skb_linearize(), from Erik
Hugne.
11) Fix autobind races et al. in netlink code, from Herbert Xu with
help from Tejun Heo and others.
12) Missing SET_NETDEV_DEV in sunvnet driver, from Sowmini Varadhan.
13) Fix various races in timewait timer and reqsk_queue_hadh_req, from
Eric Dumazet.
14) Fix array overruns in mac80211, from Johannes Berg and Dan
Carpenter.
15) Fix data race in rhashtable_rehash_one(), from Dmitriy Vyukov.
16) Fix race between poll_one_napi and napi_disable, from Neil Horman.
17) Fix byte order in geneve tunnel port config, from John W Linville.
18) Fix handling of ARP replies over lightweight tunnels, from Jiri
Benc.
19) We can loop when fib rule dumps cross multiple SKBs, fix from Wilson
Kok and Roopa Prabhu.
20) Several reference count handling bug fixes in the PHY/MDIO layer
from Russel King.
21) Fix lockdep splat in ppp_dev_uninit(), from Guillaume Nault.
22) Fix crash in icmp_route_lookup(), from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net: Fix panic in icmp_route_lookup
net: update docbook comment for __mdiobus_register()
ppp: fix lockdep splat in ppp_dev_uninit()
net: via/Kconfig: GENERIC_PCI_IOMAP required if PCI not selected
phy: marvell: add link partner advertised modes
net: fix net_device refcounting
phy: add phy_device_remove()
phy: fixed-phy: properly validate phy in fixed_phy_update_state()
net: fix phy refcounting in a bunch of drivers
of_mdio: fix MDIO phy device refcounting
phy: add proper phy struct device refcounting
phy: fix mdiobus module safety
net: dsa: fix of_mdio_find_bus() device refcount leak
phy: fix of_mdio_find_bus() device refcount leak
ip6_tunnel: Reduce log level in ip6_tnl_err() to debug
ip6_gre: Reduce log level in ip6gre_err() to debug
fib_rules: fix fib rule dumps across multiple skbs
bnx2x: byte swap rss_key to comply to Toeplitz specs
net: revert "net_sched: move tp->root allocation into fw_init()"
lwtunnel: remove source and destination UDP port config option
...
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable patches:
- fix v4.2 SEEK on files over 2 gigs
- Fix a layout segment reference leak when pNFS I/O falls back to inband I/O.
- Fix recovery of recalled read delegations
Bugfixes:
- Fix a case where NFSv4 fails to send CLOSE after a server reboot
- Fix sunrpc to wait for connections to complete before retrying
- Fix sunrpc races between transport connect/disconnect and shutdown
- Fix an infinite loop when layoutget fail with BAD_STATEID
- nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
- Fix a bogus WARN_ON_ONCE() in O_DIRECT when layout commit_through_mds is set
- Fix layoutreturn/close ordering issues"
* tag 'nfs-for-4.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS41: make close wait for layoutreturn
NFS: Skip checking ds_cinfo.buckets when lseg's commit_through_mds is set
NFSv4.x/pnfs: Don't try to recover stateids twice in layoutget
NFSv4: Recovery of recalled read delegations is broken
NFS: Fix an infinite loop when layoutget fail with BAD_STATEID
NFS: Do cleanup before resetting pageio read/write to mds
SUNRPC: xs_sock_mark_closed() does not need to trigger socket autoclose
SUNRPC: Lock the transport layer on shutdown
nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
SUNRPC: Ensure that we wait for connections to complete before retrying
SUNRPC: drop null test before destroy functions
nfs: fix v4.2 SEEK on files over 2 gigs
SUNRPC: Fix races between socket connection and destroy code
nfs: fix pg_test page count calculation
Failing to send a CLOSE if file is opened WRONLY and server reboots on a 4.x mount
of_find_net_device_by_node() uses class_find_device() internally to
lookup the corresponding network device. class_find_device() returns
a reference to the embedded struct device, with its refcount
incremented.
Add a comment to the definition in net/core/net-sysfs.c indicating the
need to drop this refcount, and fix the DSA code to drop this refcount
when the OF-generated platform data is cleaned up and freed. Also
arrange for the ref to be dropped when handling errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current users of of_mdio_find_bus() leak a struct device refcount, as
they fail to clean up the reference obtained inside class_find_device().
Fix the DSA code to properly refcount the returned MDIO bus by:
1. taking a reference on the struct device whenever we assign it to
pd->chip[x].host_dev.
2. dropping the reference when we overwrite the existing reference.
3. dropping the reference when we free the data structure.
4. dropping the initial reference we obtained after setting up the
platform data structure, or on failure.
In step 2 above, where we obtain a new MDIO bus, there is no need to
take a reference on it as we would only have to drop it immediately
after assignment again, iow:
put_device(cd->host_dev); /* drop original assignment ref */
cd->host_dev = get_device(&mdio_bus_switch->dev); /* get our ref */
put_device(&mdio_bus_switch->dev); /* drop of_mdio_find_bus ref */
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently error log messages in ip6_tnl_err are printed at 'warn'
level. This is different to other tunnel types which don't print
any messages. These log messages don't provide any information that
couldn't be deduced with networking tools. Also it can be annoying
to have one end of the tunnel go down and have the logs fill with
pointless messages such as "Path to destination invalid or inactive!".
This patch reduces the log level of these messages to 'dbg' level to
bring the visible behaviour into line with other tunnel types.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Just two small fixes:
* VHT MCS mask array overrun, reported by Dan Carpenter
* reset CQM history to always get a notification, from Sara Sharon
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently error log messages in ip6gre_err are printed at 'warn'
level. This is different to most other tunnel types which don't
print any messages. These log messages don't provide any information
that couldn't be deduced with networking tools. Also it can be annoying
to have one end of the tunnel go down and have the logs fill with
pointless messages such as "Path to destination invalid or inactive!".
This patch reduces the log level of these messages to 'dbg' level to
bring the visible behaviour into line with other tunnel types.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
dump_rules returns skb length and not error.
But when family == AF_UNSPEC, the caller of dump_rules
assumes that it returns an error. Hence, when family == AF_UNSPEC,
we continue trying to dump on -EMSGSIZE errors resulting in
incorrect dump idx carried between skbs belonging to the same dump.
This results in fib rule dump always only dumping rules that fit
into the first skb.
This patch fixes dump_rules to return error so that we exit correctly
and idx is correctly maintained between skbs that are part of the
same dump.
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fw filter uses tp->root==NULL to check if it is the old method,
so it doesn't need allocation at all in this case. This patch
reverts the offending commit and adds some comments for old
method to make it obvious.
Fixes: 33f8b9ecdb ("net_sched: move tp->root allocation into fw_init()")
Reported-by: Akshat Kakkar <akshat.1984@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP tunnel config is asymmetric wrt. to the ports used. The source and
destination ports from one direction of the tunnel are not related to the
ports of the other direction. We need to be able to respond to ARP requests
using the correct ports without involving routing.
As the consequence, UDP ports need to be fixed property of the tunnel
interface and cannot be set per route. Remove the ability to set ports per
route. This is still okay to do, as no kernel has been released with these
attributes yet.
Note that the ability to specify source and destination ports is preserved
for other users of the lwtunnel API which don't use routes for tunnel key
specification (like openvswitch).
If in the future we rework ARP handling to allow port specification, the
attributes can be added back.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using ip lwtunnels, the additional data for xmit (basically, the actual
tunnel to use) are carried in ip_tunnel_info either in dst->lwtstate or in
metadata dst. When replying to ARP requests, we need to send the reply to
the same tunnel the request came from. This means we need to construct
proper metadata dst for ARP replies.
We could perform another route lookup to get a dst entry with the correct
lwtstate. However, this won't always ensure that the outgoing tunnel is the
same as the incoming one, and it won't work anyway for IPv4 duplicate
address detection.
The only thing to do is to "reverse" the ip_tunnel_info.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Mon, Sep 21, 2015 at 02:20:22PM -0400, Tejun Heo wrote:
>
> store_release and load_acquire are different from the usual memory
> barriers and can't be paired this way. You have to pair store_release
> and load_acquire. Besides, it isn't a particularly good idea to
OK I've decided to drop the acquire/release helpers as they don't
help us at all and simply pessimises the code by using full memory
barriers (on some architectures) where only a write or read barrier
is needed.
> depend on memory barriers embedded in other data structures like the
> above. Here, especially, rhashtable_insert() would have write barrier
> *before* the entry is hashed not necessarily *after*, which means that
> in the above case, a socket which appears to have set bound to a
> reader might not visible when the reader tries to look up the socket
> on the hashtable.
But you are right we do need an explicit write barrier here to
ensure that the hashing is visible.
> There's no reason to be overly smart here. This isn't a crazy hot
> path, write barriers tend to be very cheap, store_release more so.
> Please just do smp_store_release() and note what it's paired with.
It's not about being overly smart. It's about actually understanding
what's going on with the code. I've seen too many instances of
people simply sprinkling synchronisation primitives around without
any knowledge of what is happening underneath, which is just a recipe
for creating hard-to-debug races.
> > @@ -1539,7 +1546,7 @@ static int netlink_bind(struct socket *sock, struct sockaddr *addr,
> > }
> > }
> >
> > - if (!nlk->portid) {
> > + if (!nlk->bound) {
>
> I don't think you can skip load_acquire here just because this is the
> second deref of the variable. That doesn't change anything. Race
> condition could still happen between the first and second tests and
> skipping the second would lead to the same kind of bug.
The reason this one is OK is because we do not use nlk->portid or
try to get nlk from the hash table before we return to user-space.
However, there is a real bug here that none of these acquire/release
helpers discovered. The two bound tests here used to be a single
one. Now that they are separate it is entirely possible for another
thread to come in the middle and bind the socket. So we need to
repeat the portid check in order to maintain consistency.
> > @@ -1587,7 +1594,7 @@ static int netlink_connect(struct socket *sock, struct sockaddr *addr,
> > !netlink_allowed(sock, NL_CFG_F_NONROOT_SEND))
> > return -EPERM;
> >
> > - if (!nlk->portid)
> > + if (!nlk->bound)
>
> Don't we need load_acquire here too? Is this path holding a lock
> which makes that unnecessary?
Ditto.
---8<---
The commit 1f770c0a09 ("netlink:
Fix autobind race condition that leads to zero port ID") created
some new races that can occur due to inconcsistencies between the
two port IDs.
Tejun is right that a barrier is unavoidable. Therefore I am
reverting to the original patch that used a boolean to indicate
that a user netlink socket has been bound.
Barriers have been added where necessary to ensure that a valid
portid and the hashed socket is visible.
I have also changed netlink_insert to only return EBUSY if the
socket is bound to a portid different to the requested one. This
combined with only reading nlk->bound once in netlink_bind fixes
a race where two threads that bind the socket at the same time
with different port IDs may both succeed.
Fixes: 1f770c0a09 ("netlink: Fix autobind race condition that leads to zero port ID")
Reported-by: Tejun Heo <tj@kernel.org>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Nacked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7d82410950 ("virtio: add explicit big-endian support to memory
accessors") accidentally changed the virtio_net header used by
AF_PACKET with PACKET_VNET_HDR from host-endian to big-endian.
Since virtio_legacy_is_little_endian() is a very long identifier,
define a vio_le macro and use that throughout the code instead of the
hard-coded 'false' for little-endian.
This restores the ABI to match 4.1 and earlier kernels, and makes my
test program work again.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers might call napi_disable while not holding the napi instance poll_lock.
In those instances, its possible for a race condition to exist between
poll_one_napi and napi_disable. That is to say, poll_one_napi only tests the
NAPI_STATE_SCHED bit to see if there is work to do during a poll, and as such
the following may happen:
CPU0 CPU1
ndo_tx_timeout napi_poll_dev
napi_disable poll_one_napi
test_and_set_bit (ret 0)
test_bit (ret 1)
reset adapter napi_poll_routine
If the adapter gets a tx timeout without a napi instance scheduled, its possible
for the adapter to think it has exclusive access to the hardware (as the napi
instance is now scheduled via the napi_disable call), while the netpoll code
thinks there is simply work to do. The result is parallel hardware access
leading to corrupt data structures in the driver, and a crash.
Additionaly, there is another, more critical race between netpoll and
napi_disable. The disabled napi state is actually identical to the scheduled
state for a given napi instance. The implication being that, if a napi instance
is disabled, a netconsole instance would see the napi state of the device as
having been scheduled, and poll it, likely while the driver was dong something
requiring exclusive access. In the case above, its fairly clear that not having
the rings in a state ready to be polled will cause any number of crashes.
The fix should be pretty easy. netpoll uses its own bit to indicate that that
the napi instance is in a state of being serviced by netpoll (NAPI_STATE_NPSVC).
We can just gate disabling on that bit as well as the sched bit. That should
prevent netpoll from conducting a napi poll if we convert its set bit to a
test_and_set_bit operation to provide mutual exclusion
Change notes:
V2)
Remove a trailing whtiespace
Resubmit with proper subject prefix
V3)
Clean up spacing nits
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: jmaxwell@redhat.com
Tested-by: jmaxwell@redhat.com
Signed-off-by: David S. Miller <davem@davemloft.net>
RST packets sent on behalf of TCP connections with TS option (RFC 7323
TCP timestamps) have incorrect TS val (set to 0), but correct TS ecr.
A > B: Flags [S], seq 0, win 65535, options [mss 1000,nop,nop,TS val 100
ecr 0], length 0
B > A: Flags [S.], seq 2444755794, ack 1, win 28960, options [mss
1460,nop,nop,TS val 7264344 ecr 100], length 0
A > B: Flags [.], ack 1, win 65535, options [nop,nop,TS val 110 ecr
7264344], length 0
B > A: Flags [R.], seq 1, ack 1, win 28960, options [nop,nop,TS val 0
ecr 110], length 0
We need to call skb_mstamp_get() to get proper TS val,
derived from skb->skb_mstamp
Note that RFC 1323 was advocating to not send TS option in RST segment,
but RFC 7323 recommends the opposite :
Once TSopt has been successfully negotiated, that is both <SYN> and
<SYN,ACK> contain TSopt, the TSopt MUST be sent in every non-<RST>
segment for the duration of the connection, and SHOULD be sent in an
<RST> segment (see Section 5.2 for details)
Note this RFC recommends to send TS val = 0, but we believe it is
premature : We do not know if all TCP stacks are properly
handling the receive side :
When an <RST> segment is
received, it MUST NOT be subjected to the PAWS check by verifying an
acceptable value in SEG.TSval, and information from the Timestamps
option MUST NOT be used to update connection state information.
SEG.TSecr MAY be used to provide stricter <RST> acceptance checks.
In 5 years, if/when all TCP stack are RFC 7323 ready, we might consider
to decide to send TS val = 0, if it buys something.
Fixes: 7faee5c0d5 ("tcp: remove TCP_SKB_CB(skb)->when")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell Egress rx trailer check must be fixed to
correctly detect bad bits in the third byte of the
Eggress trailer as described in the Table 28 of the
88E6060 datasheet.
The current code incorrectly omits to check the third
byte and checks the fourth byte twice.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for megaflows was introduced, OVS needed to start
installing flows with a mask applied to them. Since masking is an
expensive operation, OVS also had an optimization that would only
take the parts of the flow keys that were covered by a non-zero
mask. The values stored in the remaining pieces should not matter
because they are masked out.
While this works fine for the purposes of matching (which must always
look at the mask), serialization to netlink can be problematic. Since
the flow and the mask are serialized separately, the uninitialized
portions of the flow can be encoded with whatever values happen to be
present.
In terms of functionality, this has little effect since these fields
will be masked out by definition. However, it leaks kernel memory to
userspace, which is a potential security vulnerability. It is also
possible that other code paths could look at the masked key and get
uninitialized data, although this does not currently appear to be an
issue in practice.
This removes the mask optimization for flows that are being installed.
This was always intended to be the case as the mask optimizations were
really targetting per-packet flow operations.
Fixes: 03f0d916 ("openvswitch: Mega flow implementation")
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 51360155ec and adapts
fs/userfaultfd.c to use the old version of that function.
It didn't look robust to call __wake_up_common with "nr == 1" when we
absolutely require wakeall semantics, but we've full control of what we
insert in the two waitqueue heads of the blocked userfaults. No
exclusive waitqueue risks to be inserted into those two waitqueue heads
so we can as well stick to "nr == 1" of the old code and we can rely
purely on the fact no waitqueue inserted in one of the two waitqueue
heads we must enforce as wakeall, has wait->flags WQ_FLAG_EXCLUSIVE set.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current behavior of notifying CQM events is inconsistent:
Upon first configuration there is a cqm event with the current
status according to threshold configured, regardless of signal
stability.
When there is reconfiguration no event is sent unless there is
a significant change to the signal level according to the new
configuration.
Since the current reconfiguration behavior might cause missing
CQM events in case the current signal did not change but is on
the other side of the new threshold, fix that by resetting the
stored signal level upon reconfiguration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The HT MCS mask has 9 bytes, the VHT one only has 8 streams.
Split the loops to handle this correctly.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before allowing lockless LISTEN processing, we need to make
sure to arm the SYN_RECV timer before the req socket is visible
in hash tables.
Also, req->rsk_hash should be written before we set rsk_refcnt
to a non zero value.
Fixes: fa76ce7328 ("inet: get rid of central tcp/dccp listener timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ying Cai <ycai@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a timewait socket, we need to arm the timer before
allowing other cpus to find it. The signal allowing cpus to find
the socket is setting tw_refcnt to non zero value.
As we set tw_refcnt in __inet_twsk_hashdance(), we therefore need to
call inet_twsk_schedule() first.
This also means we need to remove tw_refcnt changes from
inet_twsk_schedule() and let the caller handle it.
Note that because we use mod_timer_pinned(), we have the guarantee
the timer wont expire before we set tw_refcnt as we run in BH context.
To make things more readable I introduced inet_twsk_reschedule() helper.
When rearming the timer, we can use mod_timer_pending() to make sure
we do not rearm a canceled timer.
Note: This bug can possibly trigger if packets of a flow can hit
multiple cpus. This does not normally happen, unless flow steering
is broken somehow. This explains this bug was spotted ~5 months after
its introduction.
A similar fix is needed for SYN_RECV sockets in reqsk_queue_hash_req(),
but will be provided in a separate patch for proper tracking.
Fixes: 789f558cfb ("tcp/dccp: get rid of central timewait timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ying Cai <ycai@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit c0bb07df7d ("netlink:
Reset portid after netlink_insert failure") introduced a race
condition where if two threads try to autobind the same socket
one of them may end up with a zero port ID. This led to kernel
deadlocks that were observed by multiple people.
This patch reverts that commit and instead fixes it by introducing
a separte rhash_portid variable so that the real portid is only set
after the socket has been successfully hashed.
Fixes: c0bb07df7d ("netlink: Reset portid after netlink_insert failure")
Reported-by: Tejun Heo <tj@kernel.org>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was already done a long time ago in
commit 64194c31a0 ("inet: Make tunnel RX/TX byte counters more consistent")
but tx path was broken (at least since 3.10).
Before the patch the gre header was included on tx.
After the patch:
$ ping -c1 192.168.0.121 ; ip -s l ls dev gre1
PING 192.168.0.121 (192.168.0.121) 56(84) bytes of data.
64 bytes from 192.168.0.121: icmp_req=1 ttl=64 time=2.95 ms
--- 192.168.0.121 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 2.955/2.955/2.955/0.000 ms
7: gre1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1468 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/gre 10.16.0.249 peer 10.16.0.121
RX: bytes packets errors dropped overrun mcast
84 1 0 0 0 0
TX: bytes packets errors dropped carrier collsns
84 1 0 0 0 0
Reported-by: Julien Meunier <julien.meunier@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
