commit 0ca49345b6 upstream.
Since commit bd972688eb
"firewire: ohci: Fix 'failed to read phy reg' on FW643 rev8",
there is a high chance that firewire-ohci fails to initialize LSI née
Agere controllers.
https://bugzilla.kernel.org/show_bug.cgi?id=65151
Peter Hurley points out the reason: IEEE 1394a:2000 clause 5A.1 (or
IEEE 1394:2008 clause 17.2.1) say: "The PHY shall insure that no more
than 10 ms elapse from the reassertion of LPS until the interface is
reset. The link shall not assert LReq until the reset is complete."
In other words, the link needs to give the PHY at least 10 ms to get
the interface operational.
With just the msleep(1) in bd972688eb, the first read_phy_reg()
during ohci_enable() may happen before the phy-link interface reset was
finished, and fail. Due to the high variability of msleep(n) with small
n, this failure was not fully reproducible, and not apparent at all with
low CONFIG_HZ setting.
On the other hand, Peter can no longer reproduce the issue with FW643
rev8. The read phy reg failures that happened back then may have had an
unrelated cause. So, just revert bd972688eb, except for the valid
comment on TSB82AA2 cards.
Reported-by: Mikhail Gavrilov
Reported-by: Jay Fenlason <fenlason@redhat.com>
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0dbe15f88b upstream.
a) Sort device IDs by vendor -- device -- revision.
b) Write quirk flags in hexadecimal. This affects the user-visible
output of "modinfo firewire-ohci". Since more flags have been added
recently, it is now easier to cope with them in hexadecimal represen-
tation. Besides, the device-specific combination of quirk flags is
shown in hexadecimal in the kernel log too. (And firewire-sbp2
presents its own quirk flags in modinfo as hexadecimals as well.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70044d71d3 upstream.
PREPARE_[DELAYED_]WORK() are being phased out. They have few users
and a nasty surprise in terms of reentrancy guarantee as workqueue
considers work items to be different if they don't have the same work
function.
firewire core-device and sbp2 have been been multiplexing work items
with multiple work functions. Introduce fw_device_workfn() and
sbp2_lu_workfn() which invoke fw_device->workfn and
sbp2_logical_unit->workfn respectively and always use the two
functions as the work functions and update the users to set the
->workfn fields instead of overriding work functions using
PREPARE_DELAYED_WORK().
This fixes a variety of possible regressions since a2c1c57be8
"workqueue: consider work function when searching for busy work items"
due to which fw_workqueue lost its required non-reentrancy property.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: linux1394-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8987583366 upstream.
Commit 8408dc1c14 "firewire: net: use dev_printk API" introduced a
use-after-free in a failure path. fwnet_transmit_packet_failed(ptask)
may free ptask, then the dev_err() call dereferenced it. The fix is
straightforward; simply reorder the two calls.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce027ed98f upstream.
Commit 54b2b50c20 "[SCSI] Disable WRITE SAME for RAID and virtual
host adapter drivers" disabled WRITE SAME support for all SBP-2 attached
targets. But as described in the changelog of commit b0ea5f19d3
"firewire: sbp2: allow WRITE SAME and REPORT SUPPORTED OPERATION CODES",
it is not required to blacklist WRITE SAME.
Bring the feature back by reverting the sbp2.c hunk of commit 54b2b50c20.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54b2b50c20 upstream.
Some host adapters do not pass commands through to the target disk
directly. Instead they provide an emulated target which may or may not
accurately report its capabilities. In some cases the physical device
characteristics are reported even when the host adapter is processing
commands on the device's behalf. This can lead to adapter firmware hangs
or excessive I/O errors.
This patch disables WRITE SAME for devices connected to host adapters
that provide an emulated target. Driver writers can disable WRITE SAME
by setting the no_write_same flag in the host adapter template.
[jejb: fix up rejections due to eh_deadline patch]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0699a73af3 upstream.
Commit 18d627113b (firewire: prevent dropping of completed iso packet
header data) was intended to be an obvious bug fix, but libdc1394 and
FlyCap2 depend on the old behaviour by ignoring all returned information
and thus not noticing that not all packets have been received yet. The
result was that the video frame buffers would be saved before they
contained the correct data.
Reintroduce the old behaviour for old clients.
Tested-by: Stepan Salenikovich <stepan.salenikovich@gmail.com>
Tested-by: Josep Bosch <jep250@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull firewure updates from Stefan Richter:
- fix controller removal when controller is in suspended state
- fix video reception on VIA VT6306 with gstreamer, MythTV, and maybe dv4l
- fix a startup issue with Agere/LSI FW643-e2
- error logging improvements and other small updates
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: dump_stack() for PHY regs read/write failures
firewire: ohci: Improve bus reset error messages
firewire: ohci: Alias dev_* log functions
firewire: ohci: Fix 'failed to read phy reg' on FW643 rev8
firewire: ohci: fix VIA VT6306 video reception
firewire: ohci: Check LPS before register access on pci removal
firewire: ohci: Fix double free_irq()
firewire: remove unnecessary alloc/OOM messages
firewire: sbp2: replace BUG_ON by WARN_ON
firewire: core: remove an always false test
firewire: Remove two unneeded checks for macros
A stack trace is an invaluable tool in determining the basis
and cause of PHY regs read/write failures.
Include PHY reg addr (and value for writes) in the diagnostic.
[Stefan R: changed whitespace]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Many of the error messages possible from bus_reset_work() do not
contain enough information to distinguish which error condition
occurred nor enough information to evaluate the error afterwards.
Differentiate all error conditions in bus_reset_work(); add
additional information to make error diagnosis possible.
[Stefan R: fixed self-ID endian conversion]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Convert dev_xxxx(ohci->card.device, ...) log functions to
ohci_xxxx(ohci, ...).
[Stefan R: Peter argues that this increases readability of the code.]
[Stefan R: changed whitespace]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add quirk for VT6306 wake bit behavior.
VT6306 seems to reread the wrong descriptor when the wake bit is
written. work around by putting a copy of the branch address in the
first descriptor of the block.
[Stefan R: This fixes the known broken video reception via gstreamer
on VIA VT6306. 100% repeatable testcase:
$ gst-launch-0.10 dv1394src \! dvdemux \! dvdec \! xvimagesink
with a camcorder or other DV source connected. Likewise for MPEG2-TS
reception via gstreamer, e.g. from TV settop boxes.
Perhaps this also fixes dv4l on VT6306, but this is as yet untested.
Kino, dvgrab or FFADO had not been affected by this chip quirk.
Additional comments from Andy:]
I've looked into some problems with the wake bit on a vt6306 family
chip (1106:3044, rev 46).
I used this firewire card in a mythtv setup (ISO receive MPEG2 stream)
with Debian 2.6.32 kernels for ~2 years without problems.
Since upgrading to 3.2, I've been having problems with the input stream
freezing -- input data stops until I restart mythtv (I expect closing
and reopening the device would be sufficient). This happens
infrequently, maybe one out of 20 recordings. I eventually determined
that the problem is more likely to occur if the system is loaded.
I isolated the kernel version as the triggering SW factor and then
specifically the change from dualbuffer back to packet-per-buffer DMA
mode.
The possibility that the controller does not properly respond to the
wake bit was suggested in
https://bugzilla.redhat.com/show_bug.cgi?id=415841, but not proven.
Based on the fact that dualbuffer mode worked while packet-per-buffer
has trouble, I guessed that upon seeing the wake bit written, the vt6306
controller only checks the branch address in the first descriptor of the
block, even if that is not the correct place to look (because the block
has multiple descriptors).
This theory seems to be correct. When the ISO reception is hung, I am
able to resume it by manually writing the branch address to the first
descriptor in the block, and then writing the wake bit.
I've had luck so far with the attached patch, so I'm including it. It's
probably not a complete solution -- I haven't tested transmit modes to
see whether they have a similar issue.
I doubt that the quirk test is any cheaper than just writing the extra
branch address in all cases, but it does reduce the risk of breaking
other hardware.
[Stefan R: omitted QUIRK_NO_MSI from VT6306 quirks table entry,
changed whitespace]
Signed-off-by: Andy Leiserson <andy@leiserson.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
A pci device can be removed while in its suspended state. If the ohci
host controller is suspended, the PHY is also in low-power mode and
LPS is disabled. If LPS is disabled, most of the host registers aren't
accessible, including IntMaskClear. Furthermore, access to these registers
when LPS is disabled can cause hard lockups on some hardware. Since
interrupts are already disabled in this mode, further action is
unnecessary.
Test LPS before attempting to write IntMaskClear to disable interrupts.
[Stefan R: whitespace changes]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
A pci device can be removed while in its suspended state.
Because the ohci driver freed the irq to suspend, free_irq() is
called twice; once from pci_remove() and again from pci_suspend(),
which issues the warning below [1].
Rather than allocate the irq in the .enable() path, move the
allocation to .probe(). Consequently, the irq is not reallocated
upon pci_resume() and thus is not freed upon pci_suspend().
[1] Warning reported by Mark Einon <mark.einon@gmail.com> when
suspending an MSI MS-1727 GT740 laptop on Ubuntu 3.5.0-22-generic
WARNING: at ./kernel/irq/manage.c:1198 __free_irq+0xa3/0x1e0()
Hardware name: MS-1727
Trying to free already-free IRQ 16
Modules linked in: ip6table_filter ip6_tables ebtable_nat ebtables <...snip...>
Pid: 4, comm: kworker/0:0 Tainted: P O 3.5.0-22-generic #34-Ubuntu
Call Trace:
[<ffffffff81051c1f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff81051d16>] warn_slowpath_fmt+0x46/0x50
[<ffffffff8103fa39>] ? default_spin_lock_flags+0x9/0x10
[<ffffffff810df6b3>] __free_irq+0xa3/0x1e0
[<ffffffff810df844>] free_irq+0x54/0xc0
[<ffffffffa005a27e>] pci_remove+0x6e/0x210 [firewire_ohci]
[<ffffffff8135ae7f>] pci_device_remove+0x3f/0x110
[<ffffffff8141fdbc>] __device_release_driver+0x7c/0xe0
[<ffffffff8141fe4c>] device_release_driver+0x2c/0x40
[<ffffffff8141f5f1>] bus_remove_device+0xe1/0x120
[<ffffffff8141cd1a>] device_del+0x12a/0x1c0
[<ffffffff8141cdc6>] device_unregister+0x16/0x30
[<ffffffff81354784>] pci_stop_bus_device+0x94/0xa0
[<ffffffffa0091c67>] acpiphp_disable_slot+0xb7/0x1a0 [acpiphp]
[<ffffffffa0090716>] ? get_slot_status+0x46/0xc0 [acpiphp]
[<ffffffffa0091d7d>] acpiphp_check_bridge.isra.15+0x2d/0xf0 [acpiphp]
[<ffffffffa0092442>] _handle_hotplug_event_bridge+0x372/0x4d0 [acpiphp]
[<ffffffff81390f8c>] ? acpi_os_execute_deferred+0x2f/0x34
[<ffffffff8116e22d>] ? kfree+0xed/0x110
[<ffffffff8107086a>] process_one_work+0x12a/0x420
[<ffffffffa00920d0>] ? _handle_hotplug_event_func+0x1d0/0x1d0 [acpiphp]
[<ffffffff8107141e>] worker_thread+0x12e/0x2f0
[<ffffffff810712f0>] ? manage_workers.isra.26+0x200/0x200
[<ffffffff81075f13>] kthread+0x93/0xa0
[<ffffffff8168d024>] kernel_thread_helper+0x4/0x10
[<ffffffff81075e80>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff8168d020>] ? gs_change+0x13/0x13
Reported-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
No need to crash and burn if S/G element sizes cannot be set to our
liking; just leave a message in the log.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The old IEEE 1394 driver stack was removed in v2.6.37. That made the
checks for two Kconfig (module) macros unneeded, since they will now
always evaluate to true. Remove these two checks.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Inspection of upper layer protocol is considered harmful, especially
if it is about ARP or other stateful upper layer protocol; driver
cannot (and should not) have full state of them.
IPv4 over Firewire module used to inspect ARP (both in sending path
and in receiving path), and record peer's GUID, max packet size, max
speed and fifo address. This patch removes such inspection by extending
our "hardware address" definition to include other information as well:
max packet size, max speed and fifo. By doing this, The neighbour
module in networking subsystem can cache them.
Note: As we have started ignoring sspd and max_rec in ARP/NDP, those
information will not be used in the driver when sending.
When a packet is being sent, the IP layer fills our pseudo header with
the extended "hardware address", including GUID and fifo. The driver
can look-up node-id (the real but rather volatile low-level address)
by GUID, and then the module can send the packet to the wire using
parameters provided in the extendedn hardware address.
This approach is realistic because IP over IEEE1394 (RFC2734) and IPv6
over IEEE1394 (RFC3146) share same "hardware address" format
in their address resolution protocols.
Here, extended "hardware address" is defined as follows:
union fwnet_hwaddr {
u8 u[16];
struct {
__be64 uniq_id; /* EUI-64 */
u8 max_rec; /* max packet size */
u8 sspd; /* max speed */
__be16 fifo_hi; /* hi 16bits of FIFO addr */
__be32 fifo_lo; /* lo 32bits of FIFO addr */
} __packed uc;
};
Note that Hardware address is declared as union, so that we can map full
IP address into this, when implementing MCAP (Multicast Cannel Allocation
Protocol) for IPv6, but IP and ARP subsystem do not need to know this
format in detail.
One difference between original ARP (RFC826) and 1394 ARP (RFC2734)
is that 1394 ARP Request/Reply do not contain the target hardware address
field (aka ar$tha). This difference is handled in the ARP subsystem.
CC: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Richter <stefanr@s5r6.in-berlin.de> says:
| As far as I can tell, it would be best to ignore max_rec and sspd from ARP
| and NDP but keep using the respective information from firewire-core
| instead (handed over by fwnet_probe()).
|
| Why? As I noted earlier, RFC 2734:1999 and RFC 3146:2001 were apparently
| written with a too simplistic notion of IEEE 1394 bus topology, resulting
| in max_rec and sspd in ARP-1394 and NDP-1394 to be useless, IMO.
|
| Consider a bus like this:
|
| A ---- B ==== C
|
| A, B, C are all IP-over-1394 capable nodes. ---- is an S400 cable hop,
| and ==== is an S800 cable hop.
|
| In case of unicasts or multicasts in which node A is involved as
| transmitter or receiver, as well as in case of broadcasts, the speeds
| S100, S200, S400 work and speed S400 is optimal.
|
| In case of anything else, IOW in case of unicasts or multicasts in which
| only nodes B and C are involved, the speeds S100, S200, S400, S800 work
| and speed S800 is optimal.
|
| Clearly, node A should indicate sspd = S400 in its ARP or NDP packets.
| But which sspd should nodes B and C set there? Maybe they set S400, which
| would work but would waste half of the available bandwidth in the second
| case. Or maybe they set S800, which is OK in the second case but would
| prohibit any communication with node A if blindly taken for correct.
|
| On the other hand, firewire-core *always* gives us the correct and optimum
| peer-to-peer speed and asynchronous packet payload, no matter how simple
| or complex the bus topology is and no matter in which temporal order nodes
| join the bus and are discovered.
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate FIFO address before registering net_device.
This is preparation to change the pseudo hardware address format
for firewire devices to include the offset of the FIFO for receipt
of unicast datagrams, instead of mangling ARP/NDP messages in the
driver layer.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send L2 multicast packet via GASP (Global asynchronous stream packet) by
seeing the multicast bit in the L2 hardware address, not by seeing upper-
layer protocol address.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
