Pull KVM update from Paolo Bonzini:
"3.19 changes for KVM:
- spring cleaning: removed support for IA64, and for hardware-
assisted virtualization on the PPC970
- ARM, PPC, s390 all had only small fixes
For x86:
- small performance improvements (though only on weird guests)
- usual round of hardware-compliancy fixes from Nadav
- APICv fixes
- XSAVES support for hosts and guests. XSAVES hosts were broken
because the (non-KVM) XSAVES patches inadvertently changed the KVM
userspace ABI whenever XSAVES was enabled; hence, this part is
going to stable. Guest support is just a matter of exposing the
feature and CPUID leaves support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (179 commits)
KVM: move APIC types to arch/x86/
KVM: PPC: Book3S: Enable in-kernel XICS emulation by default
KVM: PPC: Book3S HV: Improve H_CONFER implementation
KVM: PPC: Book3S HV: Fix endianness of instruction obtained from HEIR register
KVM: PPC: Book3S HV: Remove code for PPC970 processors
KVM: PPC: Book3S HV: Tracepoints for KVM HV guest interactions
KVM: PPC: Book3S HV: Simplify locking around stolen time calculations
arch: powerpc: kvm: book3s_paired_singles.c: Remove unused function
arch: powerpc: kvm: book3s_pr.c: Remove unused function
arch: powerpc: kvm: book3s.c: Remove some unused functions
arch: powerpc: kvm: book3s_32_mmu.c: Remove unused function
KVM: PPC: Book3S HV: Check wait conditions before sleeping in kvmppc_vcore_blocked
KVM: PPC: Book3S HV: ptes are big endian
KVM: PPC: Book3S HV: Fix inaccuracies in ICP emulation for H_IPI
KVM: PPC: Book3S HV: Fix KSM memory corruption
KVM: PPC: Book3S HV: Fix an issue where guest is paused on receiving HMI
KVM: PPC: Book3S HV: Fix computation of tlbie operand
KVM: PPC: Book3S HV: Add missing HPTE unlock
KVM: PPC: BookE: Improve irq inject tracepoint
arm/arm64: KVM: Require in-kernel vgic for the arch timers
...
It is curently possible to run a VM with architected timers support
without creating an in-kernel VGIC, which will result in interrupts from
the virtual timer going nowhere.
To address this issue, move the architected timers initialization to the
time when we run a VCPU for the first time, and then only initialize
(and enable) the architected timers if we have a properly created and
initialized in-kernel VGIC.
When injecting interrupts from the virtual timer to the vgic, the
current setup should ensure that this never calls an on-demand init of
the VGIC, which is the only call path that could return an error from
kvm_vgic_inject_irq(), so capture the return value and raise a warning
if there's an error there.
We also change the kvm_timer_init() function from returning an int to be
a void function, since the function always succeeds.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Userspace assumes that it can wire up IRQ injections after having
created all VCPUs and after having created the VGIC, but potentially
before starting the first VCPU. This can currently lead to lost IRQs
because the state of that IRQ injection is not stored anywhere and we
don't return an error to userspace.
We haven't seen this problem manifest itself yet, presumably because
guests reset the devices on boot, but this could cause issues with
migration and other non-standard startup configurations.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Some code paths will need to check to see if the internal state of the
vgic has been initialized (such as when creating new VCPUs), so
introduce such a macro that checks the nr_cpus field which is set when
the vgic has been initialized.
Also set nr_cpus = 0 in kvm_vgic_destroy, because the error path in
vgic_init() will call this function, and code should never errornously
assume the vgic to be properly initialized after an error.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The vgic_initialized() macro currently returns the state of the
vgic->ready flag, which indicates if the vgic is ready to be used when
running a VM, not specifically if its internal state has been
initialized.
Rename the macro accordingly in preparation for a more nuanced
initialization flow.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
VGIC initialization currently happens in three phases:
(1) kvm_vgic_create() (triggered by userspace GIC creation)
(2) vgic_init_maps() (triggered by userspace GIC register read/write
requests, or from kvm_vgic_init() if not already run)
(3) kvm_vgic_init() (triggered by first VM run)
We were doing initialization of some state to correspond with the
state of a freshly-reset GIC in kvm_vgic_init(); this is too late,
since it will overwrite changes made by userspace using the
register access APIs before the VM is run. Move this initialization
earlier, into the vgic_init_maps() phase.
This fixes a bug where QEMU could successfully restore a saved
VM state snapshot into a VM that had already been run, but could
not restore it "from cold" using the -loadvm command line option
(the symptoms being that the restored VM would run but interrupts
were ignored).
Finally rename vgic_init_maps to vgic_init and renamed kvm_vgic_init to
kvm_vgic_map_resources.
[ This patch is originally written by Peter Maydell, but I have
modified it somewhat heavily, renaming various bits and moving code
around. If something is broken, I am to be blamed. - Christoffer ]
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
If we detect another vCPU is running we just exit and return 0 as if we
succesfully created the VGIC, but the VGIC wouldn't actual be created.
This shouldn't break in-kernel behavior because the kernel will not
observe the failed the attempt to create the VGIC, but userspace could
be rightfully confused.
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When call kvm_vgic_inject_irq to inject interrupt, we can known which
vcpu the interrupt for by the irq_num and the cpuid. So we should just
kick this vcpu to avoid iterating through all.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When 'injecting' an edge-triggered interrupt with a falling edge we
shouldn't clear the pending state on the distributor. In fact, we
don't, because the check in vgic_validate_injection would prevent us
from ever reaching this bit of code.
Remove the unreachable snippet.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When vgic_update_irq_pending with level-sensitive false, it is need to
deactivates an interrupt, and, it can go to out directly.
Here return a false value, because it will be not need to kick.
Signed-off-by: wanghaibin <wanghaibin.wang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The EIRSR and ELRSR registers are 32-bit registers on GICv2, and we
store these as an array of two such registers on the vgic vcpu struct.
However, we access them as a single 64-bit value or as a bitmap pointer
in the generic vgic code, which breaks BE support.
Instead, store them as u64 values on the vgic structure and do the
word-swapping in the assembly code, which already handles the byte order
for BE systems.
Tested-by: Victor Kamensky <victor.kamensky@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Add support for read-only MMIO passthrough mappings by adding a
'writable' parameter to kvm_phys_addr_ioremap. For the moment,
mappings will be read-write even if 'writable' is false, but once
the definition of PAGE_S2_DEVICE gets changed, those mappings will
be created read-only.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The sgi values calculated in read_set_clear_sgi_pend_reg() and
write_set_clear_sgi_pend_reg() were horribly incorrectly multiplied by 4
with catastrophic results in that subfunctions ended up overwriting
memory not allocated for the expected purpose.
This showed up as bugs in kfree() and the kernel complaining a lot of
you turn on memory debugging.
This addresses: http://marc.info/?l=kvm&m=141164910007868&w=2
Reported-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
In order to make the number of interrupts configurable, use the new
fancy device management API to add KVM_DEV_ARM_VGIC_GRP_NR_IRQS as
a VGIC configurable attribute.
Userspace can now specify the exact size of the GIC (by increments
of 32 interrupts).
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
It is now quite easy to delay the allocation of the vgic tables
until we actually require it to be up and running (when the first
vcpu is kicking around, or someones tries to access the GIC registers).
This allow us to allocate memory for the exact number of CPUs we
have. As nobody configures the number of interrupts just yet,
use a fallback to VGIC_NR_IRQS_LEGACY.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Nuke VGIC_NR_IRQS entierly, now that the distributor instance
contains the number of IRQ allocated to this GIC.
Also add VGIC_NR_IRQS_LEGACY to preserve the current API.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we can (almost) dynamically size the number of interrupts,
we're facing an interesting issue:
We have to evaluate at runtime whether or not an access hits a valid
register, based on the sizing of this particular instance of the
distributor. Furthermore, the GIC spec says that accessing a reserved
register is RAZ/WI.
For this, add a new field to our range structure, indicating the number
of bits a single interrupts uses. That allows us to find out whether or
not the access is in range.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We now have the information about the number of CPU interfaces in
the distributor itself. Let's get rid of VGIC_MAX_CPUS, and just
rely on KVM_MAX_VCPUS where we don't have the choice. Yet.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Having a dynamic number of supported interrupts means that we
cannot relly on VGIC_NR_SHARED_IRQS being fixed anymore.
Instead, make it take the distributor structure as a parameter,
so it can return the right value.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, all the VGIC data structures are statically defined by the
*maximum* number of vcpus and interrupts it supports. It means that
we always have to oversize it to cater for the worse case.
Start by changing the data structures to be dynamically sizeable,
and allocate them at runtime.
The sizes are still very static though.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As it stands, nothing prevents userspace from injecting an interrupt
before the guest's GIC is actually initialized.
This goes unnoticed so far (as everything is pretty much statically
allocated), but ends up exploding in a spectacular way once we switch
to a more dynamic allocation (the GIC data structure isn't there yet).
The fix is to test for the "ready" flag in the VGIC distributor before
trying to inject the interrupt. Note that in order to avoid breaking
userspace, we have to ignore what is essentially an error.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
The VGIC virtual distributor implementation documentation was written a
very long time ago, before the true nature of the beast had been
partially absorbed into my bloodstream. Clarify the docs.
Plus, it fixes an actual bug. ICFRn, pfff.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Writes to GICD_ISPENDR0 and GICD_ICPENDR0 ignore all settings of the
pending state for SGIs. Make sure the implementation handles this
correctly.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Writes to GICD_ISPENDRn and GICD_ICPENDRn are currently not handled
correctly for level-triggered interrupts. The spec states that for
level-triggered interrupts, writes to the GICD_ISPENDRn activate the
output of a flip-flop which is in turn or'ed with the actual input
interrupt signal. Correspondingly, writes to GICD_ICPENDRn simply
deactivates the output of that flip-flop, but does not (of course) affect
the external input signal. Reads from GICC_IAR will also deactivate the
flip-flop output.
This requires us to track the state of the level-input separately from
the state in the flip-flop. We therefore introduce two new variables on
the distributor struct to track these two states. Astute readers may
notice that this is introducing more state than required (because an OR
of the two states gives you the pending state), but the remaining vgic
code uses the pending bitmap for optimized operations to figure out, at
the end of the day, if an interrupt is pending or not on the distributor
side. Refactoring the code to consider the two state variables all the
places where we currently access the precomputed pending value, did not
look pretty.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
If we unqueue a level-triggered interrupt completely, and the LR does
not stick around in the active state (and will therefore no longer
generate a maintenance interrupt), then we should clear the queued flag
so that the vgic can actually queue this level-triggered interrupt at a
later time and deal with its pending state then.
Note: This should actually be properly fixed to handle the active state
on the distributor.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
