Pull ARM SoC driver updates from Kevin Hilman:
"Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: soc: sunxi: Introduce SoC driver to map SRAMs
arm-cci: Add aliases for PMU events
arm-cci: Add CCI-500 PMU support
arm-cci: Sanitise CCI400 PMU driver specific code
arm-cci: Abstract handling for CCI events
arm-cci: Abstract out the PMU counter details
arm-cci: Cleanup PMU driver code
arm-cci: Do not enable CCI-400 PMU by default
firmware: qcom: scm: Add HDCP Support
ARM: berlin: add an ADC node for the BG2Q
ARM: berlin: remove useless chip and system ctrl compatibles
clk: berlin: drop direct of_iomap of nodes reg property
ARM: berlin: move BG2Q clock node
ARM: berlin: move BG2CD clock node
ARM: berlin: move BG2 clock node
clk: berlin: prepare simple-mfd conversion
pinctrl: berlin: drop SoC stub provided regmap
ARM: berlin: move pinctrl to simple-mfd nodes
pinctrl: berlin: prepare to use regmap provided by syscon
reset: berlin: drop arch_initcall initialization
...
We support decoding the bootloader values if DEBUG is defined.
But we also need to change the struct omap_hwmod flags to have
HWMOD_INIT_NO_RESET to avoid the GPMC being reset during the
boot. Otherwise just the default timings will be displayed
instead of the bootloader configured timings.
This also allows us to clean up the various GPMC related
hwmod flags. For debugging, we only need HWMOD_INIT_NO_RESET,
and HWMOD_INIT_NO_IDLE is not needed.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We currently artificially limit the parsing of GPMC connected
devices based on the device name. Let's stop doing that, it's
confusing as adding devices to .dts files with using normal
names like fpga and usb will currently cause them to not probe.
Cc: Roger Quadros <rogerq@ti.com>
Reported-by: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "ARM: tegra: Add EMC driver for v4.2-rc1" from Thierry Reding:
This introduces the EMC driver that's required to scale the external
memory frequency.
* tag 'tegra-for-4.2-emc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
memory: tegra: Add EMC frequency debugfs entry
memory: tegra: Add EMC (external memory controller) driver
memory: tegra: Add API needed by the EMC driver
of: Add Tegra124 EMC bindings
of: Document timings subnode of nvidia,tegra-mc
This file in debugfs can be used to get or set the EMC frequency.
Reading the file will return the currently set frequency in Hz, while
writing the file sets the specified frequency rounded to the next
highest frequency supported by the board.
Will be very useful when tuning memory scaling.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
[treding@nvidia.com: add "emc" debugfs directory]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EMC driver needs to know the number of external memory devices and
also needs to update the EMEM configuration based on the new rate of the
memory bus.
To know how to update the EMEM config, looks up the values of the burst
regs in the DT, for a given timing.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As this interrupt is just for development purposes, as the TRM says, and
the sheer amount of interrupts fired can seriously disrupt userspace
when testing the lower frequencies supported by the EMC.
From the TRM:
"There is one performance warning type interrupt: ARBITRATION_EMEM. It
fires when the MC detects that a request has been pending in the Row
Sorter long enough to hit the DEADLOCK_PREVENTION_SLACK_THRESHOLD. In
addition to true performance problems, this interrupt may fire in
situations such as clock-change where the EMC backpressures pending
traffic for long periods of time. This interrupt helps developers
identify and debug performance issues and configuration issues."
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The memory controller on Tegra132 is very similar to the one found on
Tegra124. But the Denver CPUs don't have an outer cache, so dcache
maintenance is done slightly differently.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Subsequent patches will add debugfs files that print the status of the
SWGROUPs. Add a new names field and complement the SoC tables with the
names of the individual SWGROUPs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for v4.1. Some of these are for drivers/soc, where we
find more and more SoC-specific drivers these days. Some are for
other driver subsystems where we have received acks from the
appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level
interface for talking to the system PMIC over a dedicated I2C
interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used
for CPU up/down and needs to be in a shared location for arm/arm64
common code.
- cleanup of ARM-CCI PMU code.
- another set of cleanusp to the OMAP GPMC code"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
soc/mediatek: Remove unused variables
clocksource: atmel-st: select MFD_SYSCON
soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs
arm-cci: Fix CCI PMU event validation
arm-cci: Split the code for PMU vs driver support
arm-cci: Get rid of secure transactions for PMU driver
arm-cci: Abstract the CCI400 PMU specific definitions
arm-cci: Rearrange code for splitting PMU vs driver code
drivers: cci: reject groups spanning multiple HW PMUs
ARM: at91: remove useless include
clocksource: atmel-st: remove mach/hardware dependency
clocksource: atmel-st: use syscon/regmap
ARM: at91: time: move the system timer driver to drivers/clocksource
ARM: at91: properly initialize timer
ARM: at91: at91rm9200: remove deprecated arm_pm_restart
watchdog: at91rm9200: implement restart handler
watchdog: at91rm9200: use the system timer syscon
mfd: syscon: Add atmel system timer registers definition
ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
soc: qcom: gsbi: Add support for ADM CRCI muxing
...
Add a driver for the NAND/External Memory Controller (NEMC) on JZ4780
and later SoCs.
The primary function of this driver is to configure parameters, such
as timings, for external memory devices using data supplied in the
device tree. Devices connected to the NEMC are represented in the DT
as children of the NEMC node, the driver uses optional properties
specified in these child nodes to configure the parameters of each
bank.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GPMC_CONFIG1_i parameters CLKACTIVATIONTIME and WAITMONITORINGTIME
have reserved values.
Raise an error if calculated timings try to program reserved values.
GPMC_CONFIG1_i ATTACHEDDEVICEPAGELENGTH and DEVICESIZE were already checked
when parsing the DT.
Explicitly comment invalid values on gpmc_cs_show_timings for
-CLKACTIVATIONTIME
-WAITMONITORINGTIME
-DEVICESIZE
-ATTACHEDDEVICEPAGELENGTH
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
The WAITMONITORINGTIME is expressed as a number of GPMC_CLK clock cycles,
even though the access is defined as asynchronous, and no GPMC_CLK clock
is provided to the external device. Still, GPMCFCLKDIVIDER is used as a divider
for the GPMC clock, so it must be programmed to define the
correct WAITMONITORINGTIME delay.
This patch correctly computes WAITMONITORINGTIME in GPMC_CLK cycles instead of GPMC_FCLK cycles,
both during programming (gpmc_cs_set_timings) and during retrieval (gpmc_cs_show_timings).
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
The WAITMONITORINGTIME is expressed as a number of GPMC_CLK clock cycles,
even though the access is defined as asynchronous, and no GPMC_CLK clock
is provided to the external device. Still, GPMCFCLKDIVIDER is used as a divider
for the GPMC clock, so it must be programmed to define the
correct WAITMONITORINGTIME delay.
Calculate GPMCFCLKDIVIDER independent of gpmc,sync-clk-ps in DT for
pure asynchronous accesses, i.e. both read and write asynchronous.
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
The WAITMONITORINGTIME is expressed as a number of GPMC_CLK clock cycles,
even though the access is defined as asynchronous, and no GPMC_CLK clock
is provided to the external device. Still, GPMCFCLKDIVIDER is used as a divider
for the GPMC clock, so it must be programmed to define the
correct WAITMONITORINGTIME delay.
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
DTS output was formatted to require additional work when copy-pasting into DTS.
Nano-second timings were replaced with interval of values that produce the same
number of clock ticks.
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
GPMC debug output is aligned to 10 characters for field names.
However, some fields have bigger names, screwing up the alignment.
Consequently, alignment was changed to longest field name (17 chars) for now.
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
OMAP2+ GPMC driver undefines DEBUG, which makes it unnecessarily
hard to turn DEBUG on. Remove the offending lines.
Signed-off-by: Robert ABEL <rabel@cit-ec.uni-bielefeld.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Fix sparse warning:
warning: symbol 'gpmc_cs_get_name' was not declared. Should it be static?
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Some GPMC_CONFIG7 register bits marked as "RESERVED", means they
shouldn't be overwritten. A typical approach to handle such bits called
"Read-Modify-Write". Writing procedure used in gpmc_cs_set_memconf()
utilizes RMW technique, but implemented incorrectly. Due to obvious typo
in code read register value is being rewritten by another value, which
leads to loss of read RESERVED bits. This patch fixes this.
While at it, replace magic numbers with named constants to improve code
readability.
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
T1040 has a different version of corenet-cf, despite being incorrectly
labelled with a fsl,corenet2-cf compatible. The t1040 version of
corenet-cf has a version register that can be read to distinguish. The
t4240/b4860 version officially does not, but testing shows that it does
and has a different value, so use that. If somehow this ends up not
being reliable and we treat a t4240/b4860 as a t1040 (the reverse
should not happen, as t1040's version register is official), currently
the worst that should happen is writing to reserved bits to enable
events that don't exist.
The changes to the t1040 version of corenet-cf that this driver cares
about are the addition of two new error events. There are also changes
to the format of cecar2, which is printed, but not interpreted, by this
driver.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull MTD updates from Brian Norris:
"Summary:
- Add device tree support for DoC3
- SPI NOR:
Refactoring, for better layering between spi-nor.c and its
driver users (e.g., m25p80.c)
New flash device support
Support 6-byte ID strings
- NAND:
New NAND driver for Allwinner SoC's (sunxi)
GPMI NAND: add support for raw (no ECC) access, for testing
purposes
Add ATO manufacturer ID
A few odd driver fixes
- MTD tests:
Allow testers to compensate for OOB bitflips in oobtest
Fix a torturetest regression
- nandsim: Support longer ID byte strings
And more"
* tag 'for-linus-20141215' of git://git.infradead.org/linux-mtd: (63 commits)
mtd: tests: abort torturetest on erase errors
mtd: physmap_of: fix potential NULL dereference
mtd: spi-nor: allow NULL as chip name and try to auto detect it
mtd: nand: gpmi: add raw oob access functions
mtd: nand: gpmi: add proper raw access support
mtd: nand: gpmi: add gpmi_copy_bits function
mtd: spi-nor: factor out write_enable() for erase commands
mtd: spi-nor: add support for s25fl128s
mtd: spi-nor: remove the jedec_id/ext_id
mtd: spi-nor: add id/id_len for flash_info{}
mtd: nand: correct the comment of function nand_block_isreserved()
jffs2: Drop bogus if in comment
mtd: atmel_nand: replace memcpy32_toio/memcpy32_fromio with memcpy
mtd: cafe_nand: drop duplicate .write_page implementation
mtd: m25p80: Add support for serial flash Spansion S25FL132K
MTD: m25p80: fix inconsistency in m25p_ids compared to spi_nor_ids
mtd: spi-nor: improve wait-till-ready timeout loop
mtd: delete unnecessary checks before two function calls
mtd: nand: omap: Fix NAND enumeration on 3430 LDP
mtd: nand: add ATO manufacturer info
...
