* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
The IW_CM_EVENT_STATUS_xxx values were used in only a couple of places;
cma.c uses -Exxx values instead, and so do the amso1100, cxgb3 and cxgb4
drivers -- only nes was using the enum values (with the mild consequence
that all nes connection failures were treated as generic errors rather
than reported as timeouts or rejections).
We can fix this confusion by getting rid of enum iw_cm_event_status and
using a plain int for struct iw_cm_event.status, and converting nes to
use -Exxx as the other iWARP drivers do.
This also gets rid of the warning
drivers/infiniband/core/cma.c: In function 'cma_iw_handler':
drivers/infiniband/core/cma.c:1333:3: warning: case value '4294967185' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1336:3: warning: case value '4294967186' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1332:3: warning: case value '4294967192' not in enumerated type 'enum iw_cm_event_status'
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Faisal Latif <faisal.latif@intel.com>
Lustre requires that clients bind to a privileged port number before
connecting to a remote server. On larger clusters (typically more
than about 1000 nodes), the number of privileged ports is exhausted,
resulting in lustre being unusable.
To handle this, we add support for reusable addresses to the rdma_cm.
This mimics the behavior of the socket option SO_REUSEADDR. A user
may set an rdma_cm_id to reuse an address before calling
rdma_bind_addr() (explicitly or implicitly). If set, other
rdma_cm_id's may be bound to the same address, provided that they all
have reuse enabled, and there are no active listens.
If rdma_listen() is called on an rdma_cm_id that has reuse enabled, it
will only succeed if there are no other id's bound to that same
address. The reuse option is exported to user space. The behavior of
the kernel reuse implementation was verified against that given by
sockets.
This patch is derived from a path by Ira Weiny <weiny2@llnl.gov>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).
This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.
All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* ib_wq is added, which is used as the common workqueue for infiniband
instead of the system workqueue. All system workqueue usages
including flush_scheduled_work() callers are converted to use and
flush ib_wq.
* cancel_delayed_work() + flush_scheduled_work() converted to
cancel_delayed_work_sync().
* qib_wq is removed and ib_wq is used instead.
This is to prepare for deprecation of flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add 802.1q VLAN support to IBoE. The VLAN tag is encoded within the
GID derived from a link local address in the following way:
GID[11] GID[12] contain the VLAN ID when the GID contains a VLAN.
The 3 bits user priority field of the packets are identical to the 3
bits of the SL.
In case of rdma_cm apps, the TOS field is used to generate the SL
field by doing a shift right of 5 bits effectively taking to 3 MS bits
of the TOS field.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for packing IBoE packet headers.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Clean up and fix ib_ud_header_init() a bit. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for IBoE device binding and IP --> GID resolution. Path
resolving and multicast joining are implemented within cma.c by
filling in the responses and running callbacks in the CMA work queue.
IP --> GID resolution always yields IPv6 link local addresses; remote
GIDs are derived from the destination MAC address of the remote port.
Multicast GIDs are always mapped to multicast MACs as is done in IPv6.
(IPv4 multicast is enabled by translating IPv4 multicast addresses to
IPv6 multicast as described in
<http://www.mail-archive.com/ipng@sunroof.eng.sun.com/msg02134.html>.)
Some helper functions are added to ib_addr.h.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch allows ports to have different link layers:
IB_LINK_LAYER_INFINIBAND or IB_LINK_LAYER_ETHERNET. This is required
for adding IBoE (InfiniBand-over-Ethernet, aka RoCE) support. For
devices that do not provide an implementation for querying the link
layer property of a port, we return a default value based on the
transport: RMA_TRANSPORT_IB nodes will return IB_LINK_LAYER_INFINIBAND
and RDMA_TRANSPORT_IWARP nodes will return IB_LINK_LAYER_ETHERNET.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new parameter to ib_register_device() so that low-level device
drivers can pass in a pointer to a callback function that will be
called for each port that is registered in sysfs. This allows
low-level device drivers to create files in
/sys/class/infiniband/<hca>/ports/<N>/
without having to poke through the internals of the RDMA sysfs handling.
There is no need for an unregister function since the kobject
reference will go to zero when ib_unregister_device() is called.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Add new IB_WR_MASKED_ATOMIC_CMP_AND_SWP and IB_WR_MASKED_ATOMIC_FETCH_AND_ADD
send opcodes that can be used to post "masked atomic compare and
swap" and "masked atomic fetch and add" work request respectively.
- Add masked_atomic_cap capability.
- Add mask fields to atomic struct of ib_send_wr
- Add new opcodes to ib_wc_opcode
The new operations are described more precisely below:
* Masked Compare and Swap (MskCmpSwap)
The MskCmpSwap atomic operation is an extension to the CmpSwap
operation defined in the IB spec. MskCmpSwap allows the user to
select a portion of the 64 bit target data for the “compare” check as
well as to restrict the swap to a (possibly different) portion. The
pseudo code below describes the operation:
| atomic_response = *va
| if (!((compare_add ^ *va) & compare_add_mask)) then
| *va = (*va & ~(swap_mask)) | (swap & swap_mask)
|
| return atomic_response
The additional operands are carried in the Extended Transport Header.
Atomic response generation and packet format for MskCmpSwap is as for
standard IB Atomic operations.
* Masked Fetch and Add (MFetchAdd)
The MFetchAdd Atomic operation extends the functionality of the
standard IB FetchAdd by allowing the user to split the target into
multiple fields of selectable length. The atomic add is done
independently on each one of this fields. A bit set in the
field_boundary parameter specifies the field boundaries. The pseudo
code below describes the operation:
| bit_adder(ci, b1, b2, *co)
| {
| value = ci + b1 + b2
| *co = !!(value & 2)
|
| return value & 1
| }
|
| #define MASK_IS_SET(mask, attr) (!!((mask)&(attr)))
| bit_position = 1
| carry = 0
| atomic_response = 0
|
| for i = 0 to 63
| {
| if ( i != 0 )
| bit_position = bit_position << 1
|
| bit_add_res = bit_adder(carry, MASK_IS_SET(*va, bit_position),
| MASK_IS_SET(compare_add, bit_position), &new_carry)
| if (bit_add_res)
| atomic_response |= bit_position
|
| carry = ((new_carry) && (!MASK_IS_SET(compare_add_mask, bit_position)))
| }
|
| return atomic_response
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_ud_header_init() first clears header and then fills up the various
fields. Later on, it tests header->immediate_present, which it has
already cleared, so the condition is always false. Fix this by adding
an immediate_present parameter and setting header->immediate_present
as is done with grh_present. Also remove unused calculation of
header_len.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A small change to reduce the size of ib_device to 1112 bytes
(from 1128).
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The defined SCTP number is incorrect (0x83, rather than 0x84), and
since it is not used anywhere, simply remove the definition.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clarify the behavior of ib_post_send() when a list of work requests is
passed in and an immediate error is returned.
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The RDMA CM is intended to support the use of a loopback address
when establishing a connection; however, the behavior of the CM
when loopback addresses are used is confusing and does not always
work, depending on whether loopback was specified by the server,
the client, or both.
The defined behavior of rdma_bind_addr is to associate an RDMA
device with an rdma_cm_id, as long as the user specified a non-
zero address. (ie they weren't just trying to reserve a port)
Currently, if the loopback address is passed to rdam_bind_addr,
no device is associated with the rdma_cm_id. Fix this.
If a loopback address is specified by the client as the destination
address for a connection, it will fail to establish a connection.
This is true even if the server is listing across all addresses or
on the loopback address itself. The issue is that the server tries
to translate the IP address carried in the REQ message to a local
net_device address, which fails. The translation is not needed in
this case, since the REQ carries the actual HW address that should
be used.
Finally, cleanup loopback support to be more transport neutral.
Replace separate calls to get/set the sgid and dgid from the
device address to a single call that behaves correctly depending
on the format of the device address. And support both IPv4 and
IPv6 address formats.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
[ Fixed RDS build by s/ib_addr_get/rdma_addr_get/ - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The struct rdma_dev_addr stores net_device address information:
the source device address, destination hardware address, and
broadcast address. For consistency, store the net_device type
rather than converting it to the rdma_node_type.
The type indicates the format of the various hardware addresses,
which is what we're concerned with, and not the RDMA node type
that the address may map to.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Provide the device interface when resolving route information to
ensure that the correct outbound device is used. This will also
simplify processing of sin6_scope_id for IPv6 support.
Based on work from:
David Wilder <dwilder@us.ibm.com>
Jason Gunthorpe <jgunthrope@obsidianresearch.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export rdma_set_ib_paths to user space to allow applications to
manually set the IB path used for connections. This allows
alternative ways for a user space application or library to obtain
path record information, including retrieving path information
from cached data, avoiding direct interaction with the IB SA.
The IB SA is a single, centralized entity that can limit scaling
on large clusters running MPI applications.
Future changes to the rdma cm can expand on this framework to
support the full range of features allowed by the IB CM, such as
separate forward and reverse paths and APM.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
