We have a pretty decent confusion about vertical timings of interlaced
modes. Peter Ross has written a patch that makes interlace modes work
on a lot more platforms/output combinations by doubling the vertical
timings.
The issue with that patch is that core drm _does_ support specifying
whether we want these vertical timings in fields or frames, we just
haven't managed to consistently use this facility. The relavant
function is drm_mode_set_crtcinfo, which fills in the crtc timing
information.
The first thing to note is that the drm core keeps interlaced modes in
frames, but displays modelines in fields. So when the crtc modeset
helper copies over the mode into adjusted_mode it will already contain
vertical timings in half-frames. The result is that the fixup code in
intel_crtc_mode_fixup doesn't actually do anything (in most cases at
least).
Now gen3+ natively supports interlaced modes and wants the vertical
timings in frames. Which is what sdvo already fixes up, at least under
some conditions.
There are a few other place that demand vertical timings in fields
but never actually deal with interlaced modes, so use frame timings
for consistency, too. These are:
- lvds panel,
- dvo encoders - dvo is the only way gen2 could support interlaced
mode, but currently we don't support any encoders that do.
- tv out - despite that the tv dac sends out an interlaced signal it
expects a progressive mode pipe configuration.
All these encoders enforce progressive modes by resetting
interlace_allowed.
Hence we always want crtc vertical timings in frames. Enforce this in
our crtc mode_fixup function and rip out any redudant timing
computations from the encoders' mode_fixup function.
v2-4: Adjust the vertical timings a bit.
v5: Split out the 'subtract-one for interlaced' fixes.
v6: Clarify issues around tv-out and gen2.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Christopher Egert <cme3000@gmail.com>
Tested-by: Alfonso Fiore <alfonso.fiore@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Clarify which bits are for which chips.
- Note that gen2 can't do interlaced directly (only via dvo tv chips).
- Move the mask to the top to make it clearer how wide this field is.
- Add defintions for all possible values.
This patch doesn't change any code.
v2: Paulo Zanoni pointed out that the pixel doubling modes do no
longer exist on ivb.
Cc: Peter Ross <pross@xvid.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Christopher Egert <cme3000@gmail.com>
Tested-by: Alfonso Fiore <alfonso.fiore@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Back-merge from drm-fixes into drm-intel-next to sort out two things:
- interlaced support: -fixes contains a bugfix to correctly clear
interlaced configuration bits in case the bios sets up an interlaced
mode and we want to set up the progressive mode (current kernels
don't support interlaced). The actual feature work to support
interlaced depends upon (and conflicts with) this bugfix.
- forcewake voodoo to workaround missed IRQ issues: -fixes only enabled
this for ivybridge, but some recent bug reports indicate that we
need this on Sandybridge, too. But in a slightly different flavour
and with other fixes and reworks on top. Additionally there are some
forcewake cleanup patches heading to -next that would conflict with
currrent -fixes.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
We want to unconditionally enable ppgtt for two reasons:
- Windows uses this on snb and later.
- We need the basic hw support to work before we can think about real
per-process address spaces and other cool features we want.
But Chris Wilson was complaining all over irc and intel-gfx that this
will blow up if we don't have a module option to disable it. Hence add
one, to prevent this.
ppgtt support seems to slightly change the timings and make crashy
things slightly more or less crashy. Now in my testing and the testing
this got on troublesome snb machines, it seems to have improved things
only. But on ivb it makes quite a few crashes happen much more often,
see
https://bugs.freedesktop.org/show_bug.cgi?id=41353
Luckily Eugeni Dodonov seems to have a set of workarounds that fix
this issue.
v2: Don't try to enable ppgtt on pre-snb.
v3: Pimp commit message and make Chris Wilson less grumpy by adding a
module option.
v4: New try at making Chris Wilson happy.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds support to bind/unbind objects and wires it up. Objects are
only put into the ppgtt when necessary, i.e. at execbuf time.
Objects are still unconditionally put into the global gtt.
v2: Kill the quick hack and explicitly pass cache_level to ppgtt_bind
like for the global gtt function. Noticed by Chris Wilson.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This just adds the setup and teardown code for the ppgtt PDE and the
last-level pagetables, which are fixed for the entire lifetime, at
least for the moment.
v2: Kill the stray debug printk noted by and improve the pte
definitions as suggested by Chris Wilson.
v3: Clean up the aperture stealing code as noted by Ben Widawsky.
v4: Paint the init code in a more pleasing colour as suggest by Chris
Wilson.
v5: Explain the magic numbers noticed by Ben Widawsky.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson and me have again stared at funny error states and it's
been pretty clear from the start that something was seriously amiss.
The seqnos last seen by the cpu were a few hundred behind those that
the gpu could have possibly emitted last before it died ...
Chris now tracked it down (hopefully, definit verdict's still out),
but in hindsight we'd have found the bug by simply dumping the cpu
side tracking of the ring head and tail registers.
Fix this and prevent an identical time-waster in the future.
Because the hangs always involved semaphores in one way or another,
we've tried to dump the mbox registers, but couldn't find any
inconsistencies. Still, dump them too.
Reviewed-and-wanted-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are all user-trigerable, so tune down their loudness a notch.
For some of these we have i-g-t tests (because they prevent
newly-discovered bugs), without this patches running the test suite
leaves behind a dirty dmesg.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen5 we also need to correctly set up swizzling in the display
scanout engine, but only there. Consolidate this into the same
function.
This has a small effect on ums setups - the kernel now also sets this
bit in addition to userspace setting it. Given that this code only
runs when userspace either can't (resume, gpu reset) or explicitly
won't(gem_init) touch the hw this shouldn't have an adverse effect.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have to do this manually. Somebody had a Great Idea.
I've measured speed-ups just a few percent above the noise level
(below 5% for the best case), but no slowdows. Chris Wilson measured
quite a bit more (10-20% above the usual snb variance) on a more
recent and better tuned version of sna, but also recorded a few
slow-downs on benchmarks know for uglier amounts of snb-induced
variance.
v2: Incorporate Ben Widawsky's preliminary review comments and
elaborate a bit about the performance impact in the changelog.
v3: Add a comment as to why we don't need to check the 3rd memory
channel.
v4: Fixup whitespace.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
An identical patch has been merged for i9xx_crtc_mode_set:
Commit 59df7b1771
Author: Christian Schmidt <schmidt@digadd.de>
Date: Mon Dec 19 20:03:33 2011 +0100
drm/intel: Fix initialization if startup happens in interlaced mode [v2]
But that one neglected to fix up the ironlake+ path.
This should fix the issue reported by Alfonso Fiore where booting with
only a HDMI cable connected to his TV failed to display anything. The
issue is that the bios set up things for 1080i and used the pannel
fitter to scale up the lower progressive resolutions. We failed to
clear the interlace bit in the PIPEACONF register, resulting in havoc.
v2: Be more paranoid and just unconditionally clear the field before
setting new values.
Cc: Peter Ross <pross@xvid.org>
Cc: Alfonso Fiore <alfonso.fiore@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
It is never correct to use intel_crtc->bpp in intel_dp_link_required,
so instead pass an explicit bpp in to this function. This patch
only supports 18bpp and 24bpp modes, which means that 10bpc modes will
be computed incorrectly. Fixing that will require more extensive
changes, and so must be addressed separately from this bugfix.
intel_dp_link_required is called from intel_dp_mode_valid and
intel_dp_mode_fixup.
* intel_dp_mode_valid is called to list supported modes; in this case,
the current crtc values cannot be relevant as the modes in question
may never be selected. Thus, using intel_crtc->bpp is never right.
* intel_dp_mode_fixup is called during mode setting, but it is run
well before ironlake_crtc_mode_set is called to set intel_crtc->bpp,
so using intel_crtc-bpp in this path can only ever get a stale
value.
Cc: Lubos Kolouch <lubos.kolouch@gmail.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42263
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44881
Tested-by: Dave Airlie <airlied@redhat.com>
Tested-by: camalot@picnicpark.org (Dell Latitude 6510)
Tested-by: Roland Dreier <roland@digitalvampire.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The c32 structure is allocated on the stack and its idx field is not
initialized before copying it to user level. This patch takes the value
from the result of the ioctl, as done for the other fields.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Evergreen and NI blit copy was broken if the buffer maps to a rectangle
whose one dimension is 16384 (max dimension allowed by these chips).
In the mainline kernel, the problem is exposed only when buffers are
very large (1G), but it's still a problem. The problem could be exposed
for smaller buffers if anyone modifies the algorithm for rectangle
construction in r600_blit_create_rect() (the reason why someone would
modify that algorithm is to tune the performance of buffer moves).
The root cause was in i2f() function which only operated on range between
0 and 16383. Fix this by extending the range of i2f() function to 0 to
32767.
While at it improve the function so that the range can be easily
extended in the future (if it becomes necessary), cleanup lines
over 80 characters, and replace in-line comments with one strategic
comment that explains the crux of the function.
Credits to michel@daenzer.net for pointing out the root cause of
the bug.
v2: Fix I2F_MAX_INPUT constant definition goof and warn only once
if input argument is out of range. Edit the comment a little
bit to avoid some linguistic confusion and make it look better
in general.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Properly set the parent device of DP i2c buses before registering them
too.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The value of this register is transferred to the V_COUNTER register at the
beginning of vertical blank. V_COUNTER is the reference for VLINE waits and
goes from VIEWPORT_Y_START to VIEWPORT_Y_START+VIEWPORT_HEIGHT during scanout,
so if VIEWPORT_Y_START is not 0, V_COUNTER actually went backwards at the
beginning of vertical blank, and VLINE waits excluding the whole scanout area
could never finish (possibly only if VIEWPORT_Y_START is larger than the length
of vertical blank in scanlines). Setting DESKTOP_HEIGHT to the framebuffer
height should prevent this for any kind of VLINE wait.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=45329 .
CC: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
