We found that on write-trough kernel is necessary to do that invalidation.
One WB is possible to use invalidation too.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Interrupts must be disabled while an interrupt state restore
(prep for interrupt return) is in progress.
Code to do this was lost in the port to the mainline kernel.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
The noMMU syscall trap has a bug that causes R11 to be zero on return to
userland. Remove the extra "save" of R11 responsible for the bug.
Remove reloading of mode indicator because r11 already contains it.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Microblaze version 7.20.d is the first MB version which can be run
on MMU linux. Please do not used previous version because they contain
HW bug.
Based on WB support was necessary to redesign whole cache design.
Microblaze versions from 7.20.a don't need to disable IRQ and cache
before working with them that's why there are special structures for it.
Signed-off-by: Michal Simek <monstr@monstr.eu>
We need to continue with next microblaze PVR version that's why
I have to remove that ancient version. These version strings not match
any versions. From Microblaze v5.00.a is possible to use this style.
I believe that none use ancients versions. If yes they will be just
labeled as unknown version.
Signed-off-by: Michal Simek <monstr@monstr.eu>
panic_timeout is in BSS section and it is cleared with BSS section.
This means that value is setup to 0.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Level interrupts need to be ack'd in the unmask handler, as in powerpc.
Among other issues, this bug causes the system clock to appear to run at
double-speed.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
The device tree handling for the gpio in the heart beat was not handling
the system when there was no gpio and it wasn't working with a newer version
of the gpio core which does not have the is-bidir property.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
After the signal frame is set up on the userspace stack, ptrace() should
be given an opportunity to single-step into the signal handler
FRV, Blackfin, mn10300 and UM. Worth to look at that patches.
Signed-off-by: Michal Simek <monstr@monstr.eu>
There is missing checking agains PVR but this is not important
for now. There are some missing checking too.
Signed-off-by: Michal Simek <monstr@monstr.eu>
We used cache_line as cache_line_lenght. For this reason
we did cache flushing 4 times longer than was necessary.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Till this patch reset always perform writen to 1.
Now we can use negative logic and perform reset write to 0.
It is opposite level than is currently read from that pin
Signed-off-by: Michal Simek <monstr@monstr.eu>
Saving is done in SAVE_STATE macros that's why another save discard
previous saved value.
This change has no effect to normal programs because they ends in any exception
and they are killed. On the other side has effect on debugging.
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch add support for dynamic function graph tracer.
There is one my expactation that I can do flush_icache after
all code modification. On microblaze is this safer than do
flush for every entry. For icache is used name flush but
correct should be invalidation - this will be fix in upcomming
new cache implementaion and WB support.
Signed-off-by: Michal Simek <monstr@monstr.eu>
