Pull ARM SoC late cleanups from Arnd Bergmann:
"These could not be part of the first cleanup branch, because they
either came too late in the cycle, or they have dependencies on other
branches. Important changes are:
- The integrator platform is almost multiplatform capable after some
reorganization (Linus Walleij)
- Minor cleanups on Zynq (Michal Simek)
- Lots of changes for Exynos and other Samsung platforms, including
further preparations for multiplatform support and the clocks
bindings are rearranged"
* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
devicetree: fix newly added exynos sata bindings
ARM: EXYNOS: Fix compilation error in cpuidle.c
ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
ARM: EXYNOS: Remove hardware.h file
ARM: SAMSUNG: Remove hardware.h inclusion
ARM: S3C24XX: Remove invalid code from hardware.h
dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
ARM: dts: Keep some essential LDOs enabled for arndale-octa board
ARM: dts: Disable MDMA1 node for arndale-octa board
ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
serial: s3c: Fix build of header without serial_core.h preinclusion
ARM: EXYNOS: Allow wake-up using GIC interrupts
ARM: EXYNOS: Stop using legacy Samsung PM code
ARM: EXYNOS: Remove PM initcalls and useless indirection
ARM: EXYNOS: Fix abuse of CONFIG_PM
ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
ARM: SAMSUNG: Move common save/restore helpers to separate file
ARM: SAMSUNG: Move Samsung PM debug code into separate file
ARM: SAMSUNG: Consolidate PM debug functions
ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
...
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
In a combined ARMv6/v7 kernel, we cannot use the
movt/movw instructions to load an immediate, as they
are not valid on ARMv6.
This changes the file to use an indirect load instead,
as lots of other implementations do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
regs-serial.h only includes linux/serial_s3c.h. Include this
header directly in samsung.S to remove unnecessary platform
dependency.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
From Shawn Guo:
i.MX SoC changes for 3.14:
- Add the initial i.MX50 SoC support
- Support device tree boot for i.MX35
- Move imx5 clock driver to use macros for clock ID
- Some random updates and non-critical fixes on clock drivers
- A few defconfig updates and minor cleanups
* tag 'imx-soc-3.14' of git://git.linaro.org/people/shawnguo/linux-2.6: (37 commits)
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
ARM: imx: update imx_v6_v7_defconfig
ARM: imx6sl: Add missing spba clock to clock tree
ARM: imx6sl: Add missing pll4_audio_div to the clock tree
ARM: imx6: Derive spdif clock from pll3_pfd3_454m
ARM: imx: use __initconst for const init definition
ARM i.MX5: fix obvious typo in ldb_di0_gate clk definition
ARM i.MX5: set CAN peripheral clock to 24 MHz parent
ARM: imx: pllv1: Fix PLL calculation for i.MX27
ARM i.MX5: fix "shift" value for lp_apm_sel on i.MX50 and i.MX53
ARM: imx: imx53: Add SATA PHY clock
ARM: imx_v6_v7_defconfig: Enable STMPE touchscreen
ARM: imx: rename IMX6SL_CLK_CLK_END to IMX6SL_CLK_END
ARM: imx: select PINCTRL at sub-architecure level
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add appropriate UART address definitions and support defines for using the
UARTs of the Freescale IMX50 SoC as debug ports.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Stop writing to the UART clock divider registers in the Tegra DEBUG_LL
code. This allows the DEBUG_LL output to use whatever baud rate was set
up by the bootloader. Some users are using higher rates than 115200.
This removes the only usage of tegra_uart_config[3], so reduce the size
allocated for that array.
Finally, fix busyuart() so that it only waits for THRE and not TEMT. For
some reason, TEMT doesn't get asserted (at least on Tegra30 Beaver) at
9600 baud, even though it does at 115200 baud. This sounds like a HW bug,
but I haven't investigated. For reference, U-Boot's serial code has
always only checked THRE, and not checked TEMT.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Paul Walmsley <pwalmsley@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
The DEBUG_LL UART address is mapped as an MMU section, hence, the
virtual address must be section-aligned. Sections are 1MB without LPAE
and 2MB with LPAE. Tegra's virtual address was only aligned to 1MB, and
hence the mapping was set up incorrectly with LPAE enabled, thus causing
a hang early during boot. Fix this by picking a different virtual address
that is aligned to 2MB.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Pull ARM updates from Russell King:
"Included in this series are:
1. BE8 (modern big endian) changes for ARM from Ben Dooks
2. big.Little support from Nicolas Pitre and Dave Martin
3. support for LPAE systems with all system memory above 4GB
4. Perf updates from Will Deacon
5. Additional prefetching and other performance improvements from Will.
6. Neon-optimised AES implementation fro Ard.
7. A number of smaller fixes scattered around the place.
There is a rather horrid merge conflict in tools/perf - I was never
notified of the conflict because it originally occurred between Will's
tree and other stuff. Consequently I have a resolution which Will
forwarded me, which I'll forward on immediately after sending this
mail.
The other notable thing is I'm expecting some build breakage in the
crypto stuff on ARM only with Ard's AES patches. These were merged
into a stable git branch which others had already pulled, so there's
little I can do about this. The problem is caused because these
patches have a dependency on some code in the crypto git tree - I
tried requesting a branch I can pull to resolve these, and all I got
each time from the crypto people was "we'll revert our patches then"
which would only make things worse since I still don't have the
dependent patches. I've no idea what's going on there or how to
resolve that, and since I can't split these patches from the rest of
this pull request, I'm rather stuck with pushing this as-is or
reverting Ard's patches.
Since it should "come out in the wash" I've left them in - the only
build problems they seem to cause at the moment are with randconfigs,
and since it's a new feature anyway. However, if by -rc1 the
dependencies aren't in, I think it'd be best to revert Ard's patches"
I resolved the perf conflict roughly as per the patch sent by Russell,
but there may be some differences. Any errors are likely mine. Let's
see how the crypto issues work out..
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (110 commits)
ARM: 7868/1: arm/arm64: remove atomic_clear_mask() in "include/asm/atomic.h"
ARM: 7867/1: include: asm: use 'int' instead of 'unsigned long' for 'oldval' in atomic_cmpxchg().
ARM: 7866/1: include: asm: use 'long long' instead of 'u64' within atomic.h
ARM: 7871/1: amba: Extend number of IRQS
ARM: 7887/1: Don't smp_cross_call() on UP devices in arch_irq_work_raise()
ARM: 7872/1: Support arch_irq_work_raise() via self IPIs
ARM: 7880/1: Clear the IT state independent of the Thumb-2 mode
ARM: 7878/1: nommu: Implement dummy early_paging_init()
ARM: 7876/1: clear Thumb-2 IT state on exception handling
ARM: 7874/2: bL_switcher: Remove cpu_hotplug_driver_{lock,unlock}()
ARM: footbridge: fix build warnings for netwinder
ARM: 7873/1: vfp: clear vfp_current_hw_state for dying cpu
ARM: fix misplaced arch_virt_to_idmap()
ARM: 7848/1: mcpm: Implement cpu_kill() to synchronise on powerdown
ARM: 7847/1: mcpm: Factor out logical-to-physical CPU translation
ARM: 7869/1: remove unused XSCALE_PMU Kconfig param
ARM: 7864/1: Handle 64-bit memory in case of 32-bit phys_addr_t
ARM: 7863/1: Let arm_add_memory() always use 64-bit arguments
ARM: 7862/1: pcpu: replace __get_cpu_var_uses
ARM: 7861/1: cacheflush: consolidate single-CPU ARMv7 cache disabling code
...
Add debug uart support for MSM8974. This patch adds a Kconfig
entry and the base address for the debug uart.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add low-level debug support for vybrid, so that earlyprintk can be
enabled for debugging early boot issue.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The PL01X debug code needs to take into account which endian mode the
processor is running in. If it is big-endian, ensure the data is swapped
appropriately.
Note, we could do this slightly more efficiently if we have an macro to
do the necessary swap for the bits used by test.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
DEBUG_UNCOMPRESS was previously disallowed for Tegra due to tegra.S's
use of global data that was not linked into the decompressor. Solve this
by declaring this symbol in tegra.S when it is being built into the
decompressor. For the kernel proper, leave the declaration in
mach-tegra/common.c as explained in the comment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Keystone's debugging is just a copy of the old 8250_32 code with a
different base address. Incorporate this into the generic 8250
debug code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the PL01X debug include can mostly stand alone without
requiring platforms to provide any macros, move it into the debug
directory so it can be directly included. This allows us to get rid of
a lot of debug-macros include files.
The autodetect case for Versatile Express and the ux500 are left alone;
these are more complicated implementations.
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the definition of the UART register addresses out of the platform
specific header files into the Kconfig files.
Acked-by: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the 8250 debug include can stand alone without requiring
platforms to provide any macros, move it into the debug directory
so it can be directly included. This allows us to get rid of a lot
of debug-macros include files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the definition of the UART register addresses out of the platform
specific header file into the Kconfig files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the definition of the UART register shift out of the platform
specific header file into the Kconfig files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
