If the ucb1x00 touchscreen is resumed while the touchscreen is being
touched, the main thread stops responding. This occurs because two
things happen:
1. When we suspended, we were woken up, and executed the loop.
Finding that the touchscreen was not pressed, we prepare to
schedule for a maximum timeout, before being stopped in
try_to_freeze().
2. an irq occurs, we disable the irq, and mark it as disabled,
and wake the thread. This wake occurs while the thread is
still within __refrigerator()
3. The thread is unfrozen, and __refrigerator() sets the threads
state back to INTERRUPTIBLE.
We then drop into schedule_timeout() with an infinite timeout and the
IRQ disabled. This prevents any further screen touches activating
the thread.
Fix this by using kthread_freezable_should_stop() which handles the
freezing issues for us outside of the hotspot where the task state
matters. Include a flag to ignore the touchscreen until it is
released to avoid sending unintended data to the application.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
gpiolib drivers should first set the output data before setting the
direction to avoid putting glitches on an output signal. As an
additional bonus, we tweak the code to avoid unnecessary register
writes to the output and direction registers if they have no need
to be updated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We were not restoring the UCB1x00 gpio output data on resume, resulting
in incorrect GPIO output data after a resume. Add the missing register
write.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The genirq layer complains if an interrupt handler returns with
interrupts enabled. The UCB1x00 handler does just this, because
ucb1x00_enable() calls mcp_enable(), which uses spin_lock_irq()
rather than spin_lock_irqsave(). Convert this, and the divisor
setting functions to use spin_lock_irqsave().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 5dd7bf59e0.
Conflicts:
scripts/mod/file2alias.c
This change is wrong on many levels. First and foremost, it causes a
regression. On boot on Assabet, which this patch gives a codec id of
'ucb1x00', it gives:
ucb1x00 ID not found: 1005
0x1005 is a valid ID for the UCB1300 device.
Secondly, this patch is way over the top in terms of complexity. The
only device which has been seen to be connected with this MCP code is
the UCB1x00 (UCB1200, UCB1300 etc) devices, and they all use the same
driver. Adding a match table, requiring the codec string to match the
hardware ID read out of the ID register, etc is completely over the top
when we can just read the hardware ID register.
Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module_param: check that bool parameters really are bool.
intelfbdrv.c: bailearly is an int module_param
paride/pcd: fix bool verbose module parameter.
module_param: make bool parameters really bool (drivers & misc)
module_param: make bool parameters really bool (arch)
module_param: make bool parameters really bool (core code)
kernel/async: remove redundant declaration.
printk: fix unnecessary module_param_name.
lirc_parallel: fix module parameter description.
module_param: avoid bool abuse, add bint for special cases.
module_param: check type correctness for module_param_array
modpost: use linker section to generate table.
modpost: use a table rather than a giant if/else statement.
modules: sysfs - export: taint, coresize, initsize
kernel/params: replace DEBUGP with pr_debug
module: replace DEBUGP with pr_debug
module: struct module_ref should contains long fields
module: Fix performance regression on modules with large symbol tables
module: Add comments describing how the "strmap" logic works
Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries. The
ARM sa11x0 mcp bus needed to be converted to that too.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (526 commits)
ASoC: twl6040 - Add method to query optimum PDM_DL1 gain
ALSA: hda - Fix the lost power-setup of seconary pins after PM resume
ALSA: usb-audio: add Yamaha MOX6/MOX8 support
ALSA: virtuoso: add S/PDIF input support for all Xonars
ALSA: ice1724 - Support for ooAoo SQ210a
ALSA: ice1724 - Allow card info based on model only
ALSA: ice1724 - Create capture pcm only for ADC-enabled configurations
ALSA: hdspm - Provide unique driver id based on card serial
ASoC: Dynamically allocate the rtd device for a non-empty release()
ASoC: Fix recursive dependency due to select ATMEL_SSC in SND_ATMEL_SOC_SSC
ALSA: hda - Fix the detection of "Loopback Mixing" control for VIA codecs
ALSA: hda - Return the error from get_wcaps_type() for invalid NIDs
ALSA: hda - Use auto-parser for HP laptops with cx20459 codec
ALSA: asihpi - Fix potential Oops in snd_asihpi_cmode_info()
ALSA: hdsp - Fix potential Oops in snd_hdsp_info_pref_sync_ref()
ALSA: hda/cirrus - support for iMac12,2 model
ASoC: cx20442: add bias control over a platform provided regulator
ALSA: usb-audio - Avoid flood of frame-active debug messages
ALSA: snd-usb-us122l: Delete calls to preempt_disable
mfd: Put WM8994 into cache only mode when suspending
...
Fix up trivial conflicts in:
- arch/arm/mach-s3c64xx/mach-crag6410.c:
renamed speyside_wm8962 to tobermory, added littlemill right
next to it
- drivers/base/regmap/{regcache.c,regmap.c}:
duplicate diff that had already come in with other changes in
the regmap tree
* git://git.infradead.org/battery-2.6: (68 commits)
power_supply: Mark da9052 driver as broken
power_supply: Drop usage of nowarn variant of sysfs_create_link()
s3c_adc_battery: Average over more than one adc sample
power_supply: Add DA9052 battery driver
isp1704_charger: Fix missing check
jz4740-battery: Fix signedness bug
power_supply: Assume mains power by default
sbs-battery: Fix devicetree match table
ARM: rx51: Add bq27200 i2c board info
sbs-battery: Change power supply name
devicetree-bindings: Propagate bq20z75->sbs rename to dt bindings
devicetree-bindings: Add vendor entry for Smart Battery Systems
sbs-battery: Rename internals to new name
bq20z75: Rename to sbs-battery
wm97xx_battery: Use DEFINE_MUTEX() for work_lock
max8997_charger: Remove duplicate module.h
lp8727_charger: Some minor fixes for the header
lp8727_charger: Add header file
power_supply: Convert drivers/power/* to use module_platform_driver()
power_supply: Add "unknown" in power supply type
...
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is required by the ASoC driver for very low power modes where the
device is fully idle but we want to update controls.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is possible that we will see another interrupt triggering at the same
time as the touchscreen interrupts so it's still worth checking other
possible sources. Almost all of the win from the fast path comes from only
needing to read the primary register and saving the I/O costs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Error handling code following a kzalloc should free the allocated data. At
this point, chip has been allocated and some fields have been initialized,
but it has not been stored anywhere, so it should be freed before leaving
the function.
A simplified version of the semantic match that finds the problem is as
follows: (http://coccinelle.lip6.fr)
// <smpl>
@r exists@
local idexpression x;
statement S;
identifier f1;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
x->f1
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch support irq for s5m series.
Basically, S5M8767 and S5M8763 irq can be handled by this patch.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
S5M series are pmic including mutiple functional devices.
It can support PMIC, RTC, Battery charger, codec.
This patch implement core driver for s5m series.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes:
WARNING: drivers/built-in.o(.text+0xf368f): Section mismatch in reference from
the function stmpe_probe() to the function .devinit.text:stmpe_chip_init()
The function stmpe_probe() references the function __devinit stmpe_chip_init().
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes:
drivers/mfd/stmpe.c:114:1: warning: data definition has no type or storage
class [enabled by default]
drivers/mfd/stmpe.c:114:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Wimplicit-int]
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
STMPE i2c is a bool and should depend on I2c=y.
That fixes:
drivers/built-in.o: In function `i2c_block_write':
stmpe-i2c.c:(.text+0xf4553): undefined reference to
+`i2c_smbus_write_i2c_block_data'
drivers/built-in.o: In function `i2c_block_read':
stmpe-i2c.c:(.text+0xf457f): undefined reference to
+`i2c_smbus_read_i2c_block_data'
drivers/built-in.o: In function `i2c_reg_write':
stmpe-i2c.c:(.text+0xf45ab): undefined reference to
`i2c_smbus_write_byte_data'
drivers/built-in.o: In function `i2c_reg_read':
stmpe-i2c.c:(.text+0xf45d4): undefined reference to `i2c_smbus_read_byte_data'
drivers/built-in.o: In function `stmpe_init':
stmpe-i2c.c:(.init.text+0xaf22): undefined reference to `i2c_register_driver'
drivers/built-in.o: In function `stmpe_exit':
stmpe-i2c.c:(.exit.text+0x5e5): undefined reference to `i2c_del_driver'
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
