commit 9b53b39243 upstream.
Errata:
Certain conditions on the scsi bus may casue the 53C1030 to incorrectly signal
a SCSI_DATA_UNDERRUN to the host.
Workaround 1:
For an Errata on LSI53C1030 When the length of request data
and transfer data are different with result of command (READ or VERIFY),
DID_SOFT_ERROR is set.
Workaround 2:
For potential trouble on LSI53C1030. It is checked whether the length of
request data is equal to the length of transfer and residual.
MEDIUM_ERROR is set by incorrect data.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c1ccaf2478 upstream.
After dma-mapping an SG list provided by the SCSI midlayer, iser has
to make sure the mapped SG is "aligned for RDMA" in the sense that its
possible to produce one mapping in the HCA IOMMU which represents the
whole SG. Next, the mapped SG is formatted for registration with the HCA.
This patch re-writes the logic that does the above, to make it clearer
and simpler. It also fixes a bug in the being aligned for RDMA checks,
where a "start" check wasn't done but rather only "end" check.
[commit message in RH kernel tree: "Under heavy load, without the patch,
the HCA can be programmed to write (corrupt) into pages/location which
doesn't belong to the SG associated with the actual I/O and cause a
kernel oops."]
Signed-off-by: Alexander Nezhinsky <alexandern@voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 31bde71c20 upstream.
The tpm_tis driver already has a list of supported pnp_device_ids.
This patch simply exports that list as a MODULE_DEVICE_TABLE() so that
the module autoloader will discover and load the module at boottime.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a1de02dccf upstream.
The "offset" member in ext4_io_end holds bytes, not blocks, so
ext4_lblk_t is wrong - and too small (u32).
This caused the async i/o writes to sparse files beyond 4GB to fail
when they wrapped around to 0.
Also fix up the type of arguments to ext4_convert_unwritten_extents(),
it gets ssize_t from ext4_end_aio_dio_nolock() and
ext4_ext_direct_IO().
Reported-by: Giel de Nijs <giel@vectorwise.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c8afb44682 upstream.
Creating many small files in rapid succession on a small
filesystem can lead to spurious ENOSPC; on a 104MB filesystem:
for i in `seq 1 22500`; do
echo -n > $SCRATCH_MNT/$i
echo XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX > $SCRATCH_MNT/$i
done
leads to ENOSPC even though after a sync, 40% of the fs is free
again.
This is because we reserve worst-case metadata for delalloc writes,
and when data is allocated that worst-case reservation is not
usually needed.
When freespace is low, kicking off an async writeback will start
converting that worst-case space usage into something more realistic,
almost always freeing up space to continue.
This resolves the testcase for me, and survives all 4 generic
ENOSPC tests in xfstests.
We'll still need a hard synchronous sync to squeeze out the last bit,
but this fixes things up to a large degree.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 17bd55d037 upstream.
ext4, at least, would like to start pushing on writeback if it starts
to get close to ENOSPC when reserving worst-case blocks for delalloc
writes. Writing out delalloc data will convert those worst-case
predictions into usually smaller actual usage, freeing up space
before we hit ENOSPC based on this speculation.
Thanks to Jens for the suggestion for the helper function,
& the naming help.
I've made the helper return status on whether writeback was
started even though I don't plan to use it in the ext4 patch;
it seems like it would be potentially useful to test this
in some cases.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Jan Kara <jack@suse.cz>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c0ce77b832 upstream.
Reinette found the reason for the warnings that
happened occasionally when a hw-offloaded scan
finished; her description of the problem:
mac80211 will defer the handling of scan requests if it is
busy with management work at the time. The scan requests
are deferred and run after the work has completed. When
this occurs there are currently two problems.
* The scan request for hardware scan is not fully populated
with the band and channels to scan not initialized.
* When the scan is queued the state is not correctly updated
to reflect that a scan is in progress. The problem here is
that when the driver completes the scan and calls
ieee80211_scan_completed() a warning will be triggered
since mac80211 was not aware that a scan was in progress.
The reason is that the queued scan work will start
the hw scan right away when the hw_scan_req struct
has already been allocated. However, in the first
pass it will not have been filled, which happens
at the same time as setting the bits. To fix this,
simply move the allocation after the pending work
test as well, so that the first iteration of the
scan work will call __ieee80211_start_scan() even
in the hardware scan case.
Bug-identified-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 301e99ce4a upstream.
One the changes in commit d7979ae4a "svc: Move close processing to a
single place" is:
err_delete:
- svc_delete_socket(svsk);
+ set_bit(SK_CLOSE, &svsk->sk_flags);
return -EAGAIN;
This is insufficient. The recvfrom methods must always call
svc_xprt_received on completion so that the socket gets re-queued if
there is any more work to do. This particular path did not make that
call because it actually destroyed the svsk, making requeue pointless.
When the svc_delete_socket was change to just set a bit, we should have
added a call to svc_xprt_received,
This is the problem that b0401d7253 attempted to fix, incorrectly.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1b644b6e6f upstream.
This reverts commit b0401d7253, which
moved svc_delete_xprt() outside of XPT_BUSY, and allowed it to be called
after svc_xpt_recived(), removing its last reference and destroying it
after it had already been queued for future processing.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f5822754ea upstream.
This reverts commit b292cf9ce7. The
commit that it attempted to patch up,
b0401d7253, was fundamentally wrong, and
will also be reverted.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit dc83d6e27f upstream.
For nfsd we provide users the option of mapping uid's to server-side
supplementary group lists. That makes sense for nfsd, but not
necessarily for other rpc users (such as the callback client).
So move that lookup to svcauth_unix_set_client, which is a
program-specific method.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 627a2d3c29 upstream.
If a component device has a merge_bvec_fn then as we never call it
we must ensure we never need to. Currently this is done by setting
max_sector to 1 PAGE, however this does not stop a bio being created
with several sub-page iovecs that would violate the merge_bvec_fn.
So instead set max_phys_segments to 1 and set the segment boundary to the
same as a page boundary to ensure there is only ever one single-page
segment of IO requested at a time.
This can particularly be an issue when 'xen' is used as it is
known to submit multiple small buffers in a single bio.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The __module_ref_addr() problem disappears in 2.6.34-rc kernels because these
percpu accesses were re-factored.
__module_ref_addr() should use per_cpu_ptr() to obfuscate the pointer
(RELOC_HIDE is needed for per cpu pointers).
This non-standard per-cpu pointer use has been introduced by commit
720eba31f4
It causes a NULL pointer exception on some configurations when CONFIG_TRACING is
enabled on 2.6.33. This patch fixes the problem (acknowledged by Randy who
reported the bug).
It did not appear to hurt previously because most of the accesses were done
through local_inc, which probably obfuscated the access enough that no compiler
optimizations were done. But with local_read() done when CONFIG_TRACING is
active, this becomes a problem. Non-CONFIG_TRACING is probably affected as well
(module.c contains local_set and local_read that use __module_ref_addr()), but I
guess nobody noticed because we've been lucky enough that the compiler did not
generate the inappropriate optimization pattern there.
This patch should be queued for the 2.6.29.x through 2.6.33.x stable branches.
(tested on 2.6.33.1 x86_64)
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Eric Dumazet <dada1@cosmosbay.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Tejun Heo <tj@kernel.org>
CC: Ingo Molnar <mingo@elte.hu>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Linus Torvalds <torvalds@linux-foundation.org>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mainline kernel as of 2.6.34-rc5 is not affected by this problem because
commit 10fad5e46f fixed it by refactoring.
lockdep fix incorrect percpu usage
Should use per_cpu_ptr() to obfuscate the per cpu pointers (RELOC_HIDE is needed
for per cpu pointers).
git blame points to commit:
lockdep.c: commit 8e18257d29
But it's really just moving the code around. But it's enough to say that the
problems appeared before Jul 19 01:48:54 2007, which brings us back to 2.6.23.
It should be applied to stable 2.6.23.x to 2.6.33.x (or whichever of these
stable branches are still maintained).
(tested on 2.6.33.1 x86_64)
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: Randy Dunlap <randy.dunlap@oracle.com>
CC: Eric Dumazet <dada1@cosmosbay.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Tejun Heo <tj@kernel.org>
CC: Ingo Molnar <mingo@elte.hu>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Linus Torvalds <torvalds@linux-foundation.org>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 014f61504a upstream.
When Wacom devices wake up from a sleep, the switch mode command
(wacom_query_tablet_data) is needed before wacom_open is called.
wacom_query_tablet_data should not be executed inside wacom_open
since wacom_open is called more than once during probe.
Reported-and-tested-by: Anton Anikin <Anton@Anikin.name>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 598856407d upstream.
Make sure, that TCP has a nonzero RTT estimation after three-way
handshake. Currently, a listening TCP has a value of 0 for srtt,
rttvar and rto right after the three-way handshake is completed
with TCP timestamps disabled.
This will lead to corrupt RTO recalculation and retransmission
flood when RTO is recalculated on backoff reversion as introduced
in "Revert RTO on ICMP destination unreachable"
(f1ecd5d9e7).
This behaviour can be provoked by connecting to a server which
"responds first" (like SMTP) and rejecting every packet after
the handshake with dest-unreachable, which will lead to softirq
load on the server (up to 30% per socket in some tests).
Thanks to Ilpo Jarvinen for providing debug patches and to
Denys Fedoryshchenko for reporting and testing.
Changes since v3: Removed bad characters in patchfile.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c0cd884af0 upstream.
Official patch to fix the r8169 frame length check error.
Based on this initial thread:
http://marc.info/?l=linux-netdev&m=126202972828626&w=1
This is the official patch to fix the frame length problems in the r8169
driver. As noted in the previous thread, while this patch incurs a performance
hit on the driver, its possible to improve performance dynamically by updating
the mtu and rx_copybreak values at runtime to return performance to what it was
for those NICS which are unaffected by the ideosyncracy (if there are any).
Summary:
A while back Eric submitted a patch for r8169 in which the proper
allocated frame size was written to RXMaxSize to prevent the NIC from dmaing too
much data. This was done in commit fdd7b4c330. A
long time prior to that however, Francois posted
126fa4b9ca, which expiclitly disabled the MaxSize
setting due to the fact that the hardware behaved in odd ways when overlong
frames were received on NIC's supported by this driver. This was mentioned in a
security conference recently:
http://events.ccc.de/congress/2009/Fahrplan//events/3596.en.html
It seems that if we can't enable frame size filtering, then, as Eric correctly
noticed, we can find ourselves DMA-ing too much data to a buffer, causing
corruption. As a result is seems that we are forced to allocate a frame which
is ready to handle a maximally sized receive.
This obviously has performance issues with it, so to mitigate that issue, this
patch does two things:
1) Raises the copybreak value to the frame allocation size, which should force
appropriately sized packets to get allocated on rx, rather than a full new 16k
buffer.
2) This patch only disables frame filtering initially (i.e., during the NIC
open), changing the MTU results in ring buffer allocation of a size in relation
to the new mtu (along with a warning indicating that this is dangerous).
Because of item (2), individuals who can't cope with the performance hit (or can
otherwise filter frames to prevent the bug), or who have hardware they are sure
is unaffected by this issue, can manually lower the copybreak and reset the mtu
such that performance is restored easily.
Signed-off-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
