This adds registers save/restore for Ironlake to make suspend work.
Signed-off-by: Guo, Chaohong <chaohong.guo@intel.com>
[zhenyuw: some code re-orgnization, and add more save/restore for
FDI link and transcoder registers, also fix palette register for Ironlake]
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When coming back from DPMS or turning on a display, make sure we have
the watermarks set up before turning on the display plane, otherwise we
may get underruns.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Turns out G4x needs to have sensible watermarks set, especially for
self-refresh enabled modes. Add support for it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Must set filter selection as hardcoded coefficients for medium 3x3
filtering, which matches vbios setting for Ironlake.
This fixes display corrupt issue on HP arrandale with new vbios.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For new stepping of PCH, the display reference clock
is fully under driver's control. This one trys to setup
all needed reference clock for different outputs. Older
stepping of PCH chipset should be ignoring this.
This fixes output failure issue on newer PCH which requires
driver to take control of reference clock enabling.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Original radeon didn't have a connector table in the
bios. Check for the CRT table and if we have one,
add a VGA connector.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Need to check the return type for the quirk function
to decide whether we add the connectors and encoders.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Sometimes we will get the incorrect display modeline when parsing the detailed
timing in EDID. For example:
>hsync/vsync width is zero
>sync is beyond the blank.
So add the basic check for the detailed timing in EDID to avoid the incorrect
display modeline.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
D1MODE_INTERLEAVE_EN was getting set in some cases
in the encoder quirks function due to the changes in
5a9bcacc0a
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based partly on a patch from
Christian Koenig <deathsimple@vodafone.de>
- fix several memory leaks in radeon_connector->edid handling
- store edid in radeon_connector->edid in detect() or get_modes()
- switch hdmi detect code to use radeon_connector->edid
- add support for oem boards multiple connectors that share
a ddc line.
- short circuit lvds_detect() if have a stored edid
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To enable framebuffer compression on a g4x, we not only need the buffer
to tiled (X only), we also need to hold a fence register for the buffer.
Currently we only install a fence register for pre-i965s when setting up
the scanout buffer. Rather than adding some convoluted logic to
g4x_enable_fbc() to acquire a fence register, and perhaps to
g4x_disable_fbc() to release it again, we can extend the acquisition
during setup to all chipsets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Turns out some machines, like the ThinkPad X40 don't come back if you
don't save/restore this register.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
- crtc 0 routing was wrong
- need to clear various timing bits in FP_GEN_CNTL
- need to set FP_H/V2_SYNC_STRT_WID regs for crtc 1
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_encoder->active_device defines the active routing
between the encoder and connector. The encoder fixup and
dpms functions need to know the active_device to function
properly. Setting active_device in the prepare hook was
too late in some cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
FDI M/N calculation hasn't taken the current pipe color depth into account,
but always set as 24bpp. This one checks current pipe color depth setting,
and change FDI M/N calculation a little to use bits_per_pixel first, then
convert to bytes_per_pixel later.
This fixes display corrupt issue on Arrandle LVDS with 1600x900 panel
in 18bpp dual-channel mode.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Until we figure out the right setting for powersave features on
Ironlake, disable it for now. Also disable watermark update,
which has new registers for it on Ironlake too.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Resolved against the Pineview FBC changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
If the device didn't support EDP, we would bail out too soon.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
[anholt: Pulled this patch out of the patch for adding quirks to
enable reclocking.]
Signed-off-by: Eric Anholt <eric@anholt.net>
This hasn't fixed the regressions we were testing against, but clearly
should be required.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
According to the spec the LVDS_BORDER_ENABLE bit decides whether the border
data should be included in the active display and data sent to the panel.
Border should be used when in VGA centered (un-scaled) mode or when scaling
a 4:3 source image to a wide screen panel (typical 16:9).
So when the LVDS scaling is used, decide whether the LVDS_BORDER should be
enabled or not according to the current scaling mode.
At the same time fix the typo error in LVDS center scaling mode.
https://bugs.freedesktop.org/show_bug.cgi?id=23789
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
tested-by: Zhao Jian <jian.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Pineview doesn't have this FBC mechanism, so this code doesn't apply.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
drm modes are objects with indentifiers. Make sure to preserve
the mode id when copying mode params.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
