This feature is optional and is enabled if the BIOS requests any
Windows OSI strings. It can also be enabled by the host OS.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_hw_write_gpe_enable_reg() to re-enable a GPE after
an event signaled by it has been handled. However, this function
writes the entire GPE enable mask to the GPE's enable register which
may not be correct. Namely, if one of the other GPEs in the same
register was previously enabled by acpi_enable_gpe() and subsequently
disabled using acpi_set_gpe(), acpi_hw_write_gpe_enable_reg() will
re-enable it along with the target GPE.
To fix this issue rework acpi_hw_write_gpe_enable_reg() so that it
calls acpi_hw_low_set_gpe() with a special action value,
ACPI_GPE_COND_ENABLE, that will make it only enable the GPE if the
corresponding bit in its register's enable_for_run mask is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_ev_enable_gpe() for enabling GPEs at the low level,
which is incorrect, because this function only enables the GPE if the
corresponding bit in its enable register's enable_for_run mask is set.
This causes acpi_set_gpe() to work incorrectly if used for enabling
GPEs that were not previously enabled with acpi_enable_gpe(). As a
result, among other things, wakeup-only GPEs are never enabled by
acpi_enable_wakeup_device(), so the devices that use them are unable
to wake up the system.
To fix this issue remove acpi_ev_enable_gpe() and its counterpart
acpi_ev_disable_gpe() and replace acpi_hw_low_disable_gpe() with
acpi_hw_low_set_gpe() that will be used instead to manipulate GPE
enable bits at the low level. Make the users of acpi_ev_enable_gpe()
and acpi_ev_disable_gpe() call acpi_hw_low_set_gpe() instead and
make sure that GPE enable masks are only updated by acpi_enable_gpe()
and acpi_disable_gpe() when GPE reference counters change from 0
to 1 and from 1 to 0, respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
These were used before cpuidle by the native ACPI idle driver,
which tracked promotion and demotion between states.
The code was referenced by CONFIG_ACPI_PROCFS
for /proc/acpi/processor/*/power,
but as we no longer do promotion/demotion, that
reference has been a NOP since the transition.
Signed-off-by: Len Brown <len.brown@intel.com>
ERST is a way provided by APEI to save and retrieve hardware error
record to and from some simple persistent storage (such as flash).
The Linux kernel support implementation is quite simple and workable
in NMI context. So it can be used to save hardware error record into
flash in hardware error exception or NMI handler, where other more
complex persistent storage such as disk is not usable. After saving
hardware error records via ERST in hardware error exception or NMI
handler, the error records can be retrieved and logged into disk or
network after a clean reboot.
For more information about ERST, please refer to ACPI Specification
version 4.0, section 17.4.
This patch incorporate fixes from Jin Dongming.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
CC: Jin Dongming <jin.dongming@np.css.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Hardware Error Device (PNP0C33) is used to report some hardware errors
notified via SCI, mainly the corrected errors. Some APEI Generic
Hardware Error Source (GHES) may use SCI on hardware error device to
notify hardware error to kernel.
After receiving notification from ACPI core, it is forwarded to all
listeners via a notifier chain. The listener such as APEI GHES should
check corresponding error source for new events when notified.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now, a dedicated HEST tabling parsing code is used for PCIE AER
firmware_first setup. It is rebased on general HEST tabling parsing
code of APEI. The firmware_first setup code is moved from PCI core to
AER driver too, because it is only AER related.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
HEST describes error sources in detail; communicating operational
parameters (i.e. severity levels, masking bits, and threshold values)
to OS as necessary. It also allows the platform to report error
sources for which OS would typically not implement support (for
example, chipset-specific error registers).
HEST information may be needed by other subsystems. For example, HEST
PCIE AER error source information describes whether a PCIE root port
works in "firmware first" mode, this is needed by general PCIE AER
error subsystem. So a public HEST tabling parsing interface is
provided.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some ACPI IO accessing need to be done in atomic context. For example,
APEI ERST operations may be used for permanent storage in hardware
error handler. That is, it may be called in atomic contexts such as
IRQ or NMI, etc. And, ERST/EINJ implement their operations via IO
memory/port accessing. But the IO memory accessing method provided by
ACPI (acpi_read/acpi_write) maps the IO memory during it is accessed,
so it can not be used in atomic context. To solve the issue, the IO
memory should be pre-mapped during EINJ/ERST initializing. A linked
list is used to record which memory area has been mapped, when memory
is accessed in hardware error handler, search the linked list for the
mapped virtual address from the given physical address.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We have ported Rafael's major GPE changes
(ACPI: Use GPE reference counting to support shared GPEs) into ACPICA code base.
But the port and Rafael's original patch have some differences, so we made
below patch to make linux GPE code consistent with ACPICA code base.
Most changes are about comments and coding styles.
Other noticeable changes are based on:
Rafael: Reduce code duplication related to GPE lookup
https://patchwork.kernel.org/patch/86237/
Rafael: Always use the same lock for GPE locking
https://patchwork.kernel.org/patch/90471/
A new field gpe_count in struct acpi_gpe_block_info to record the number
of individual GPEs in block.
Rename acpi_ev_save_method_info to acpi_ev_match_gpe_method.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Robert Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change will enable debug object output via a global variable,
acpi_gbl_enable_aml_debug_object. This will help with remote machine
debugging. Also, moved all debug object support code to a new
file, exdebug.c. Entire debug object module can now be
configured out of the ACPICA build if desired.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI spec includes a provision for hardware to provide EDID via the
ACPI video extension. In the KMS world it's necessary for a way to obtain
this from within the kernel. Add a function that either returns the EDID
for the provided ACPI display ID or the first display of the provided type.
Also add support for ensuring that devices with legacy IDs are supported.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
