* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 5329 ColdFire periphal addressing
uclinux: add process name to allocation error message
m68knommu: correct the mii calculations for 532x ColdFire FEC
m68knommu: add ColdFire M532x to the FEC configuration options
m68knommu: fix syscall restarting
m68knommu: remove the obsolete and long unused comempci chip support
m68knommu: remove the no longer used PCI support option
m68knommu: remove obsolete and unused eLIA board
m68knommu: set NO_DMA
m68knommu: fix cache flushing for the 527x ColdFire processors
m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
m68knommu: use one exist from execption
I noticed (the hard way) that the mcf.c driver doesn't support the fractional precision register on the MCF5272. This makes the console dicey at 115200 baud and a system clock of 66.0 MHz. On the other hand, if your hardware is running at 66.666 MHz, it probably isn't a problem.
Patch submitted by John Adamson <jadamson@allen-organ.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This patch adds the SCSPTR register to the sh-sci driver in
the case of sh7723 to make sure early printk builds properly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for "ns16850" as supported value
of the compatible node in flat device tree uart descriptions.
This is needed for example when you have a XR16C2850 uart
connected to a PPC405's external bus controller.
Signed-off-by: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix the following problem, related to hardware flow control (CTS/RTS):
Transmitting while CTS line is asserted in DMA mode, due to not checking
for tx-stopped condition.
We found these problems while testing the UARTs with hardware
flow-control.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: "Andrew Victor" <avictor.za@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was not implemented correctly for the pnx8xxx_uart driver.
[From further discussion:
Correct, you can look to it as two separate bugs:
a) the next character is not ignored while it should;
b) the status bits 31-8 are copied to the 'ch' variable while they shouldn't.
Both bugs prevent correct break signal handling (and therefore correct
behaviour of the magic SysRq key). Bug b didn't cause too much trouble
earlier because in most situations the status bits are all zero; for
this case they unfortunately aren't.
]
Signed-off-by: Mischa Jonker <mischa.jonker@nxp.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add SupraExpress 336i PnP Voice Modem
Tested and working with the following device: (output from lspnp -v)
01:01.00 SUP1381 (unknown)
state = active
io 0x2f8-0x2ff
irq 3
Signed-off-by: Daniel Gagnon <daniel.gagnon@yahoo.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of netmos 9835 hardware is handled by parport-serial. IBM introduces
a device which doesn't have any parallel ports and have screwed subdevice
PCI id (not corresponding to port numbers).
Handle this device (9710:9835 1014:0299) properly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b430428a18 ("8250: Don't clobber
spinlocks.") introduced a regression on the parisc architecture, which
broke the handover to the serial port at boottime.
early_serial_setup() was changed to only copy a subset of the uart_port
fields, and sadly the "type" and "line" fields were forgotten and thus
the serial port was not initialized and could not be used for a
handover. This patch fixes this by copying the missing fields.
As this change to early_serial_setup() doesn't need an initialized
spinlock in the uart_port struct any longer, we can drop the spinlock
initialization in the superio driver.
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall found an un-needed check in the neo driver. Her patch moves
the check to cover the code dereferencing it, however it cannot be NULL
anyway so remove the NULL check instead.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Always set CONFIG_SERIAL_SAMSUNG_UARTS when building any
of the S3C platforms as even if the driver is not selected
there it is still the facility for the machine files to
register configuration data for the possibility of the
driver being built.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for the nwp serial device which is connected to a DCR bus. It
uses the of_serial device driver to determine necessary properties from
the device tree. The supported device is added as serial port number 85.
NWP stands for network processor and it is part of the QPACE - Quantum
Chromodynamics Parallel Computing on the Cell Broadband Engine project.
The implementation is a lightweight uart implementation with the focus
to consume as little resources as possible and it is connected to a
DCR bus.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Commit d87a6d9 ("drivers/serial/: remove CVS keywords") removed one
space too many in the printk in serial8250_init(). Put it back in (and
add a comma for clarity).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cavium UART implementation is not covered by existing uart_configS.
Define a new uart_config (PORT_OCTEON) which is specified by OCTEON
platform device registration code.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add flag value UPF_FIXED_TYPE which specifies that the UART type is
known and should not be probed. For this case the UARTs properties
are just copied out of the uart_config entry.
This allows us to keep SOC specific 8250 probe code out of 8250.c. In
this case we know the serial hardware will not be changing as it is on
the same silicon as the CPU, and we can specify it with certainty in
the board/cpu setup code.
The alternative is to load up 8250.c with a bunch of OCTEON specific
special cases in the probing code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to use Cavium OCTEON specific serial i/o drivers, we first
patch the 8250 driver to use replaceable I/O functions. Compatible
I/O functions are added for existing iotypeS.
An added benefit of this change is that it makes it easy to factor
some of the existing special cases out to board/SOC specific support
code.
The alternative is to load up 8250.c with a bunch of OCTEON specific
iotype code and bug work-arounds.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
