Add decaying history of predicted idle time, instead of using the last early
wakeup. This logic helps menu governor do better job of predicting idle time.
With this change, we also measured noticable (~8%) power savings on
a DP server system with CPUs supporting deep C states, when system
was lightly loaded. There was no change to power or perf on other load
conditions.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It's showing up as regressions; disabling it very likely just papers
over an underlying issue, but time is running out for 2.6.28, lets get
back to this for 2.6.29
Fixes: #11826 and #11893
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v28-range-hrtimers-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (37 commits)
hrtimers: add missing docbook comments to struct hrtimer
hrtimers: simplify hrtimer_peek_ahead_timers()
hrtimers: fix docbook comments
DECLARE_PER_CPU needs linux/percpu.h
hrtimers: fix typo
rangetimers: fix the bug reported by Ingo for real
rangetimer: fix BUG_ON reported by Ingo
rangetimer: fix x86 build failure for the !HRTIMERS case
select: fix alpha OSF wrapper
select: fix alpha OSF wrapper
hrtimer: peek at the timer queue just before going idle
hrtimer: make the futex() system call use the per process slack value
hrtimer: make the nanosleep() syscall use the per process slack
hrtimer: fix signed/unsigned bug in slack estimator
hrtimer: show the timer ranges in /proc/timer_list
hrtimer: incorporate feedback from Peter Zijlstra
hrtimer: add a hrtimer_start_range() function
hrtimer: another build fix
hrtimer: fix build bug found by Ingo
hrtimer: make select() and poll() use the hrtimer range feature
...
cpuidle accounts the idle time for the C-state it was trying to enter and
not to the actual state that the driver eventually entered. The driver may
select a different state than the one chosen by cpuidle due to
constraints like bus-mastering, etc.
Change the time acounting code to look at the dev->last_state after
returning from target_state->enter(). Driver can modify dev->last_state
internally, inside the enter routine to reflect the actual C-state
entered.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As part of going idle, we already look at the time of the next timer event to determine
which C-state to select etc.
This patch adds functionality that causes the timers that are past their
soft expire time, to fire at this time, before we calculate the next wakeup
time. This functionality will thus avoid wakeups by running timers before
going idle rather than specially waking up for it.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
ladder governor only honored latency requirement when promoting C-states.
Instead. it should check for latency requirement on each idle call,
and demote to appropriate C-state when there is a latency requirement change.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
There is a bug in menu governor where we have
if (data->elapsed_us < data->elapsed_us + measured_us)
with measured_us already having elapsed_us added in tickless case here
unsigned int measured_us =
cpuidle_get_last_residency(dev) + data->elapsed_us;
Also, it should be last_residency, not measured_us, that need to be used to
do comparing and distinguish between expected & non-expected events.
Refactor menu_reflect() to fix these two problems.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Wei Gang <gang.wei@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
poll_idle was added to CPUIDLE, just as a low latency idle handler, to be
used in cases when user desires CPUs not to enter any idle state at all. It
was supposed to be a run time idle=poll option to the user. But, it was indeed
getting used during normal menu and ladder governor default case, with no
special user setting (Reported by Linus Torvalds).
Change below ensures that poll_idle will not be used unless user explicitly
asks pm_qos infrastructure for zero latency requirement.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
These attributes are really sysdev class attributes. The incorrect
definition leads to an oops because of recent changes which make sysdev
attributes use a different prototype.
Based on Andi's f718cd4add ("sched: make
scheduler sysfs attributes sysdev class devices")
Reported-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pm_idle_save resp. pm_idle_old can be NULL when the restore code in
acpi_processor_cst_has_changed() resp. cpuidle_uninstall_idle_handler()
is called. This can set pm_idle unconditinally to NULL, which causes the
kernel to panic when calling pm_idle in the x86 idle code. This was
covered by an extra check for !pm_idle in the x86 idle code, which was
removed during the x86 idle code refactoring.
Instead of restoring the pm_idle check in the x86 code prevent the
acpi/cpuidle code to set pm_idle to NULL.
Reported by: Dhaval Giani http://lkml.org/lkml/2008/7/2/309
Based on a debug patch from Ingo Molnar
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cpuidle and acpi driver interaction bug with the way cpuidle_register_driver()
is called. Due to this bug, there will be oops on
AC<->DC on some systems, where they support C-states in one DC and not in AC.
The current code does
ON BOOT:
Look at CST and other C-state info to see whether more than C1 is
supported. If it is, then acpi processor_idle does a
cpuidle_register_driver() call, which internally enables the device.
ON CST change notification (AC<->DC) and on suspend-resume:
acpi driver temporarily disables device, updates the device with
any new C-states, and reenables the device.
The problem is is on boot, there are no C2, C3 states supported and we skip
the register. Later on AC<->DC, we may get a CST notification and we try
to reevaluate CST and enabled the device, without actually registering it.
This causes breakage as we try to create /sys fs sub directory, without the
parent directory which is created at register time.
Thanks to Sanjeev for reporting the problem here.
http://bugzilla.kernel.org/show_bug.cgi?id=10394
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 9b12e18cdc
'ACPI: cpuidle: Support C1 idle time accounting'
was implicated in a 100% C0 idle regression.
http://bugzilla.kernel.org/show_bug.cgi?id=10076
It pointed out a potential problem where the menu governor
may get confused by the C-state residency time from poll
idle or C1 idle, where this timing info is not accurate.
This inaccuracy is due to interrupts being handled
before we account for C-state exit.
Do not mark TIME_VALID for CO poll state.
Mark C1 time as valid only with the MWAIT (CSTATE_FFH) entry method.
This makes governors use the timing information only when it is correct and
eliminates any wrong policy decisions that may result from invalid timing
information.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
cpuidle C-state sysfs node time and usage are very easy to overflow because
they are all of unsigned int type, time will overflow within about two hours,
usage will take longer time to overflow, but they are increasing for ever.
This patch will convert them to unsigned long long.
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a new sysfs entry under cpuidle states. desc - can be used by driver to
communicate to userspace any specific information about the state.
This helps in identifying the exact hardware C-states behind the ACPI C-state
definition.
Idea is to export this through powertop, which will help to map the C-state
reported by powertop to actual hardware C-state.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The last posted version of this patch gave compile error
on IA64. So, here goes yet another rewrite of the patch.
Convert cpu_idle_wait() to cpuidle_kick_cpus() which is
SMP-only, and gives error on non supported CPU.
Changes from last patch sent by Kevin:
Moved the definition of kick_cpus back to cpuidle.c from cpuidle.h:
* Having it in .h gives #error on archs which includes the header file without
actually having CPU_IDLE configured. To make it work in .h, we need one more
#ifdef around that code which makes it messy.
* Also, the function is only called from one file. So, it can be in declared
statically in .c rather than making it available to everyone who includes
the .h file.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a default poll idle state with 0 latency. Provides an option to users
to use poll_idle by using 0 as the latency requirement.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The following patch is a generalization of the latency.c implementation done
by Arjan last year. It provides infrastructure for more than one parameter,
and exposes a user mode interface for processes to register pm_qos
expectations of processes.
This interface provides a kernel and user mode interface for registering
performance expectations by drivers, subsystems and user space applications on
one of the parameters.
Currently we have {cpu_dma_latency, network_latency, network_throughput} as
the initial set of pm_qos parameters.
The infrastructure exposes multiple misc device nodes one per implemented
parameter. The set of parameters implement is defined by pm_qos_power_init()
and pm_qos_params.h. This is done because having the available parameters
being runtime configurable or changeable from a driver was seen as too easy to
abuse.
For each parameter a list of performance requirements is maintained along with
an aggregated target value. The aggregated target value is updated with
changes to the requirement list or elements of the list. Typically the
aggregated target value is simply the max or min of the requirement values
held in the parameter list elements.
>From kernel mode the use of this interface is simple:
pm_qos_add_requirement(param_id, name, target_value):
Will insert a named element in the list for that identified PM_QOS
parameter with the target value. Upon change to this list the new target is
recomputed and any registered notifiers are called only if the target value
is now different.
pm_qos_update_requirement(param_id, name, new_target_value):
Will search the list identified by the param_id for the named list element
and then update its target value, calling the notification tree if the
aggregated target is changed. with that name is already registered.
pm_qos_remove_requirement(param_id, name):
Will search the identified list for the named element and remove it, after
removal it will update the aggregate target and call the notification tree
if the target was changed as a result of removing the named requirement.
>From user mode:
Only processes can register a pm_qos requirement. To provide for
automatic cleanup for process the interface requires the process to register
its parameter requirements in the following way:
To register the default pm_qos target for the specific parameter, the
process must open one of /dev/[cpu_dma_latency, network_latency,
network_throughput]
As long as the device node is held open that process has a registered
requirement on the parameter. The name of the requirement is
"process_<PID>" derived from the current->pid from within the open system
call.
To change the requested target value the process needs to write a s32
value to the open device node. This translates to a
pm_qos_update_requirement call.
To remove the user mode request for a target value simply close the device
node.
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: fix build again]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: mark gross <mgross@linux.intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Adam Belay <abelay@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert cpu_idle_wait() to cpuidle_kick_cpus() macro which is
SMP-only, and gives error on non supported CPU.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
There is no need for kobject_unregister() anymore, thanks to Kay's
kobject cleanup changes, so replace all instances of it with
kobject_put().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop using kobject_register, as this way we can control the sending of
the uevent properly, after everything is properly initialized.
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
