commit 6984ab1ab35f422292b7781c65284038bcc0f6a6 upstream.
A wrong decoding of the touch coordinate message causes a wrong touch
ID. Touch ID for dual touch must be 0 or 1.
According to the actual Neonode nine byte touch coordinate coding,
the state is transported in the lower nibble and the touch ID in
the higher nibble of payload byte five.
Signed-off-by: Knut Wohlrab <Knut.Wohlrab@de.bosch.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eda5ecc0a6b865561997e177c393f0b0136fe3b7 upstream.
The trigger delay algorithm that converts from microseconds to
the register value looks incorrect. According to most of the PMIC
documentation, the equation is
delay (Seconds) = (1 / 1024) * 2 ^ (x + 4)
except for one case where the documentation looks to have a
formatting issue and the equation looks like
delay (Seconds) = (1 / 1024) * 2 x + 4
Most likely this driver was written with the improper
documentation to begin with. According to the downstream sources
the valid delays are from 2 seconds to 1/64 second, and the
latter equation just doesn't make sense for that. Let's fix the
algorithm and the range check to match the documentation and the
downstream sources.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 92d57a73e4 ("input: Add support for Qualcomm PMIC8XXX power key")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 162f98dea487206d9ab79fc12ed64700667a894d upstream.
The gtco driver expects at least one valid endpoint. If given malicious
descriptors that specify 0 for the number of endpoints, it will crash in
the probe function. Ensure there is at least one endpoint on the interface
before using it.
Also let's fix a minor coding style issue.
The full correct report of this issue can be found in the public
Red Hat Bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=1283385
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 950336ba3e4a1ffd2ca60d29f6ef386dd2c7351d upstream.
The ati_remote2 driver expects at least two interfaces with one
endpoint each. If given malicious descriptor that specify one
interface or no endpoints, it will crash in the probe function.
Ensure there is at least two interfaces and one endpoint for each
interface before using it.
The full disclosure: http://seclists.org/bugtraq/2016/Mar/90
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c6ba456711687b794dcf285856fc14e2c76074f upstream.
The powermate driver expects at least one valid USB endpoint in its
probe function. If given malicious descriptors that specify 0 for
the number of endpoints, it will crash. Validate the number of
endpoints on the interface before using them.
The full report for this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/85
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4f1b06d685d11ebdaccf11c0db1cb3c78736862 upstream.
We should set device's capabilities first, and then register it,
otherwise various handlers already present in the kernel will not be
able to connect to the device.
Reported-by: Lauri Kasanen <cand@gmx.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd0d0d4de582a6a61c032332c91f4f4cb2bab569 upstream.
Without i8042.nomux=1 the Elantech touch pad is not working at all on
a Fujitsu Lifebook U745. This patch does not seem necessary for all
U745 (maybe because of different BIOS versions?). However, it was
verified that the patch does not break those (see opensuse bug 883192:
https://bugzilla.opensuse.org/show_bug.cgi?id=883192).
Signed-off-by: Aurélien Francillon <aurelien@francillon.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6544a1df11c48c8413071aac3316792e4678fbfb upstream.
When using a protocol v2 or v3 hardware, elantech uses the function
elantech_report_semi_mt_data() to report data. This devices are rather
creepy because if num_finger is 3, (x2,y2) is (0,0). Yes, only one valid
touch is reported.
Anyway, userspace (libinput) is now confused by these (0,0) touches,
and detect them as palm, and rejects them.
Commit 3c0213d17a ("Input: elantech - fix semi-mt protocol for v3 HW")
was sufficient enough for xf86-input-synaptics and libinput before it has
palm rejection. Now we need to actually tell libinput that this device is
a semi-mt one and it should not rely on the actual values of the 2 touches.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Few Android drivers e.g. uid_cputime and PPPoLAC/oPNS,
keyreset/combo, cpufreq_interactive etc.. fail to build
as kernel modules. Instead of fixing the build lets
make these drivers non-modular (switch config to "bool"
from "tristate" in Kconfig) since Android doesn't
support building kernel modules anyway.
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Switched do_restart to run in a seperate workqueue to handle
cases where kernel_restart hangs.
Change-Id: I1ecd61f8d0859f1a86d37c692351d644b5db9c69
Signed-off-by: Daniel Rosenberg <drosen@google.com>
keyreset now registers a keycombo driver that acts as the old
keyreset driver acted.
Change-Id: I08f5279e3a33b267571b699697f9f54508868983
Signed-off-by: Daniel Rosenberg <drosen@google.com>
Keycombo lets you provide a key up and key down function, and an
optional time delay for key down. The driver will call the key
down function after the specified key combo has been held for the
speicified time delay. After you release the combo, if the key down
has happened, it calls key up.
Change-Id: I6a9a94e96a8f58fadd908fd1dc7944b9102a089f
Signed-off-by: Daniel Rosenberg <drosen@google.com>
This driver allows userspace to receive notification when client
specified key combinations are pressed.
The client opens /dev/keychord and writes a list of keychords
for the driver to monitor.
The client then reads or polls /dev/keychord for notifications.
A client specified ID for the keychord is returned from read()
when a keychord press is detected.
Signed-off-by: Mike Lockwood <lockwood@android.com>
keychord: fix to build without CONFIG_PREEMPT
Change-Id: I911f13aeda4224b6fa57863bc7e8972fec8837fb
Add a platform device in the board file to specify a reset key-combo.
The first time the key-combo is detected a work function that syncs
the filesystems is scheduled. If all the keys are released and then
pressed again, it calls panic. Reboot on panic should be set for
this to work.
Change-Id: I9d54283ca1fba45e4b1ae1a407524cdda8171143
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Remove the early suspend handler. Leave the suspend functions
for now, they should eventually get called through a userspace
interface.x
Change-Id: I67f9dafe32fe32577bab93c42b95824db96c215c
Signed-off-by: Colin Cross <ccross@android.com>
Supports keyboard matrixces, direct inputs, direct outputs and axes connected to gpios.
Change-Id: I5e921e6e3a1cc169316ee3b665f4cc21b5735114
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Nick Pelly <npelly@google.com>
