The profile sensor clickpad in a Cr-48 Chromebook does a reasonable job
of tracking individual fingers. This tracking isn't perfect, but,
experiments show that it works better than just passing "semi-mt" data
to userspace, and making userspace try to deduce where the fingers are
given a bounding box.
This patch tries to report correct two-finger positions instead of the
{(min_x, min_y), (max_x, max_y)} for profile sensor clickpads on Cr-48
chromebooks. Note that this device's firmware always reports the higher
(smaller y) finger in the "sgm" packet, and the lower (larger y) finger
in the "agm" packet. Thus, when a new finger arrives on the pad, the
kernel driver uses input core's contact tracking facilities to match
contacts with slots.
Inspired by patch by Daniel Kurtz <djkurtz@chromium.org> and Chung-yih
Wang <cywang@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Semi-MT devices are pointers too, so let's tell that to
input_mt_init_slots(), as well as let it set up the devices as semi-MT,
instead of us doing it manually.
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for querying the physical size from the touchpad for Rushmore
and v7 touchpads, and use that to tell userspace the device resolution.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Such as found on the new Toshiba Portégé Z30-A and Z40-A.
Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com>
[hdegoede@redhat.com: Remove softbutton handling, this is done in userspace]
[hdegoede@redhat.com: Report INPUT_PROP_BUTTONPAD]
[hdegoede@redhat.com: Do not report fake PRESSURE, reporting BTN_TOUCH is
enough]
[hdegoede@redhat.com: Various cleanups / refactoring]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If we detect more then 2 fingers report 2 touches, rather then only
reporting the upper left corner of the bounding box.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move all the semi-mt specific handling shared between the v3 and v4
handling code to a common helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For v3 protocol devices, use the more accurate single touch data when the
mt data contains only one finger. Note the mt data reporting a finger count
of 1 should never happen, but better safe then sorry.
This brings the v3 bitmap handling in line with what the v4 code does,
allowing to factor out the common bits into a helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When there are 2 fingers on the pad we don't know which one is which, so
use input_mt_assign_slots to make sure the right set of coordinates ends
up in the right slot.
Besides ensuring things end up in the right slot, this also results in a
nice cleanup, since sync_frame also handles non mt position and btn_touch
reporting.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a preparation patch for switching the DIY mt handling to using
input_mt_assign_slots && input_mt_sync_frame.
struct alps_fields is quite large, so while making changes to almost all uses
of it lets put it in our priv data instead of on the stack.
Having it in our priv data also allows using it directly for storing values
which need to be cached, rather then having separate x, y, z, fingers, etc.
copies in our priv data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes 2 fingers at the same height or width on the touchpad getting
reported at different y / x coordinates.
Note num_bits is always at least 1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
alps_process_bitmap was resetting the point bit-count as soon as it saw
2 0 bits in a row. This means that unless the high point actually is at
the end of the bitmap, it would always get its num_bits set to 0.
Instead reset num_bits to 0 on a 0->1 transition, so that with > 2 fingers
we only count the number of bits occupied by the highest finger.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Factor out the identical code for getting the bitmap points for x and y into
a helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rushmore models don't have the Y-axis data in the bitmap inverted. Since
we now have 2 different Y orientations, make the Y bitmap data processing
use a forward loop like the X bitmap data processing, unifying the 2,
and invert the data later, except on Rushmore.
So far no-one has noticed this because the synaptics driver only uses the
non mt coordinates (except on clickpads, and there are no alps clickpads
using process_bitmap).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
V3 models only report mt bitmap data when there are 2 or more fingers on
the touchpad. So always generate 2 positions in alps_process_bitmap, and
for v3 models only fall back to st data when there was no mt data in a
mt packet (which should never happen).
This fixes 2 finger scrolling not working when using 2 fingers close to
each other.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit 421e08c41f fixed the reported min/max for the X and Y axis,
but unfortunately, it broke the resolution of those same axis.
On the t540p, the resolution is the same regarding X and Y. It is not
a problem for xf86-input-synaptics because this driver is only interested
in the ratio between X and Y.
Unfortunately, xf86-input-cmt uses directly the resolution, and having a
null resolution leads to some divide by 0 errors, which are translated by
-infinity in the resulting coordinates.
Reported-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchpad on the GIGABYTE U2442 not only stops communicating when we try
to set bit 3 (enable real hardware resolution) of reg_10, but on some BIOS
versions also when we set bit 1 (enable two finger mode auto correct).
I've asked the original reporter of:
https://bugzilla.kernel.org/show_bug.cgi?id=61151
To check that not setting bit 1 does not lead to any adverse effects on his
model / BIOS revision, and it does not, so this commit fixes the touchpad
not working on these versions by simply never setting bit 1 for laptop
models with the no_hw_res quirk.
Reported-and-tested-by: James Lademann <jwlademann@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At least the Dell Vostro 5470 elantech *clickpad* reports right button
clicks when clicked in the right bottom area:
https://bugzilla.redhat.com/show_bug.cgi?id=1103528
This is different from how (elantech) clickpads normally operate, normally
no matter where the user clicks on the pad the pad always reports a left
button event, since there is only 1 hardware button beneath the path.
It looks like Dell has put 2 buttons under the pad, one under each bottom
corner, causing this.
Since this however still clearly is a real clickpad hardware-wise, we still
want to report it as such to userspace, so that things like finger movement
in the bottom area can be properly ignored as it should be on clickpads.
So deal with this weirdness by simply mapping a right click to a left click
on elantech clickpads. As an added advantage this is something which we can
simply do on all elantech clickpads, so no need to add special quirks for
this weird model.
Reported-and-tested-by: Elder Marco <eldermarco@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Most of the affected models share pnp-ids for the touchpad. So switching
to pnp-ids give us 2 advantages:
1) It shrinks the quirk list
2) It will lower the new quirk addition frequency, ie the recently added W540
quirk would not have been necessary since it uses the same LEN0034 pnp ids
as other models already added before it
As an added bonus it actually puts the quirk on the actual psmouse, rather
then on the machine, which is technically more correct.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
