This patch changes internal hardware DP_CON/DM_CON switch according to
cable type. The SM5502 MUIC device can set hardware switch as following:
- OPEN (not connected state) / USB / UART / AUDIO
Also, this patch set VBUSIN switch according to cable type.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch detect whether cable is connected or not and the cable type
after completing kernel/platform booting using system_power_efficient_wq.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch add new SM5502 MUIC(Micro-USB Interface Controller) device by using
EXTCON subsystem. The extcon-sm5502 driver is capable of identifying the type
of the external power source and attached accessory. An external power sources,
such as Deticated Charger or a standard USB port, are able to charge the battery
in the smart phone via the connector.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Previously we would do a regulator get against the main Arizona device
to obtain the MICVDD regulator. Arizona is an MFD device and normally
MICVDD will be supplied by one of its children (the arizona-micsupp
regulator). As devres destruction for the MFD device will run after all
its children have been destroyed, the regulator will be destroyed before
devres calls regulator_put. This causes a warning from both the
destruction of the child node, as the regulator is still open, and from
the put of the regulator as the regulator device has already been
destroyed.
A simple fix here is to get the regulator against the extcon device
itself such that devres runs when the child is destroyed. This has the
additional benefit that if for some reason the extcon driver is unloaded
the regulator reference won't hang around until the MFD is unloaded.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message. The following
checkpatch warning is also removed.
WARNING: Possible unnecessary 'out of memory' message
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
[Acked by Charles Keepax for arizona part]
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch modifies mfd driver to use regmap for handling interrupts.
It allows to simplify irq handling process. This modifications needed
to make small changes in function drivers, which use interrupts.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The higher levels of impedance have a higher minimum value than the
first level. As the same value was used for all levels, higher impedances
were reported with a very low level of accuracy. This patch applies the
approriate lower threshold for each level, whilst we are changing things
add a define for the maximum value at each level to improve readability.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
We can use the bypass mode on the MICVDD reg for button detection, as
the comment in the code states, however the code was mistakenly
disabling bypass. This patch corrects this and allows bypass mode during
button detection.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
devm_input_allocate_device already sets the parent device to be that
passed to it, we also set this manually in arizona_extcon_probe. This
patch removes the redundant set from arizona_extcon_probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch use devm_extcon_dev_allocate() to simplify the memory control
of extcon device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
This patch use devm_extcon_dev_allocate() to simplify the memory control
of extcon device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
This patch use devm_extcon_dev_allocate() to simplify the memory control
of extcon device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
This patch use devm_extcon_dev_allocate() to simplify the memory control
of extcon device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
This patch add device managed devm_extcon_dev_{allocate,free} to automatically
free the memory of extcon_dev structure without handling free operation.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
This patch add APIs to control the extcon device on extcon provider driver.
The extcon_dev_allocate() allocates the memory of extcon device and initializes
supported cables. And then extcon_dev_free() decrement the reference of the
device of extcon device and free the memory of the extcon device. This APIs
must need to implement devm_extcon_dev_allocate()/free() APIs.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
