The Yukon EC Ultra chips have transmit settings for store and
forward and PCI buffering. By setting these appropriately, normal
performance goes from 750Mbytes/sec to 940Mbytes/sec (non-jumbo).
It is also possible to do Jumbo mode, but it means turning off
TSO and checksum offload so the performance gets worse. There isn't
enough buffering for checksum offload to work.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to make sure and disable ASF on all chip types. Otherwise, there may be
random reboots.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There should never be descriptor error unless hardware or driver is buggy.
But if an error occurs, print useful information, clear irq, and recover.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This device is having all sorts of problems that lead to data corruption
and system instability. It gets receive status and data out of order,
it generates descriptor and TSO errors, etc.
Until the problems are resolved, it should not be used by anyone
who cares about there system.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The basic structure of "normal" UDP/IP/Ethernet
frames (that actually work):
- It starts with the Ethernet header (dest MAC, src MAC, etc.)
- The next part is occupied by the IP header (version info, length of
packet, id=0, fragment offset=0, checksum, from / to address, etc.)
- Then comes the UDP header (src / dest port, length, checksum)
- Actual payload
- Ethernet checksum
Now what's different for IP fragment:
- The IP header has id set to some value (same for all fragments),
offset is set appropriately (i.e. 0 for first fragment, following
according to size of other fragments), size is the length of the frame.
- UDP header is unchanged. I.e. length is according to full UDP
datagram, not just the part within the actual frame! But this is only
true within the first frame: all following frames don't have a valid
UDP-header at all.
The spidernet silicon seems to be quite intelligent: It's able to
compute (IP / UDP / Ethernet) checksums on the fly and tests if frames
are conforming to RFC -- at least conforming to RFC on complete frames.
But IP fragments are different as explained above:
I.e. for IP fragments containing part of a UDP datagram it sees
incompatible length in the headers for IP and UDP in the first frame
and, thus, skips this frame. But the content *is* correct for IP
fragments. For all following frames it finds (most probably) no valid
UDP header at all. But this *is* also correct for IP fragments.
The Linux IP-stack seems to be clever in this point. It expects the
spidernet to calculate the checksum (since the module claims to be able
to do so) and marks the skb's for "normal" frames accordingly
(ip_summed set to CHECKSUM_HW).
But for the IP fragments it does not expect the driver to be capable to
handle the frames appropriately. Thus all checksums are allready
computed. This is also flaged within the skb (ip_summed set to
CHECKSUM_NONE).
Unfortunately the spidernet driver ignores that hints. It tries to send
the IP fragments of UDP datagrams as normal UDP/IP frames. Since they
have different structure the silicon detects them the be not
"well-formed" and skips them.
The following one-liner against 2.6.21-rc2 changes this behavior. If the
IP-stack claims to have done the checksumming, the driver should not
try to checksum (and analyze) the frame but send it as is.
Signed-off-by: Norbert Eicker <n.eicker@fz-juelich.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove assumption that PHY interrupts use GPIOs 3 and 5.
Deal with PHY interrupts connected to any GPIO pins.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reuse the incoming skb when a clientless abort req is recieved.
The release of RDMA connections HW resources might be deferred in
low memory situations.
Ensure that no further activity is passed up to the RDMA driver
for these connections.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Nonpae guest pdes are shadowed by two pae ptes, so we double the offset
twice: once to account for the pte size difference, and once because we
need to shadow pdes for a single guest pde.
But when writing to the upper guest pde we also need to truncate the
lower bits, otherwise the multiply shifts these bits into the pde index
and causes an access to the wrong shadow pde. If we're at the end of the
page (accessing the very last guest pde) we can even overflow into the
next host page and oops.
Signed-off-by: Avi Kivity <avi@qumranet.com>
* Last write during i2c_xfer is of the wrong byte (off-by-1).
* Read length is wrong for some of the reads (mistakenly used the PEC
version)
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Users have been complaining about the w83627ehf driver flooding their logs
with debug messages like:
w83627ehf 9191-0a10: Increasing fan 4 clock divider from 64 to 128
or:
w83627ehf 9191-0290: Increasing fan 4 clock divider from 4 to 8
The reason is that we failed to actually write the LSB of the encoded clock
divider value for that fan, causing the next read to report the same old value
again and again.
Additionally, the fan number was improperly reported, making the bug harder to
find.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that the last patch to change set_cs to be kept in the
controller's structure instead of the platform data was an incomplete
change, and did not change the references to platfrom data in the setup
xfer code. (This can prevent an oops.)
Reported-by: <Ling.Alex@iac.com.tw>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In mthca_arbel_fmr_unmap(), the high bits of the key are masked off.
This gets rid of the effect of adjust_key(), which makes sure that
bits 3 and 23 of the key are equal when the Sinai throughput
optimization is enabled, and so it may happen that an FMR will end up
with bits 3 and 23 in the key being different. This causes data
corruption, because when enabling the throughput optimization, the
driver promises the HCA firmware that bits 3 and 23 of all memory keys
will always be equal.
Fix by re-applying adjust_key() after masking the key.
Thanks to Or Gerlitz for reproducing the problem, and Ariel Shahar for
help in debug.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We only map DMA when cmd->request_bufflen is non-zero for non-sg
buffers, we thus should make the same check when unmapping.
Based upon a report from Pasi Pirhonen.
Signed-off-by: David S. Miller <davem@davemloft.net>
3w-xxxx emulates a REQUEST_SENSE response by simply returning nothing.
Unfortunately, it's assuming that the REQUEST_SENSE command is
implemented with use_sg == 0, which is no longer the case. The oops
occurs because it's clearing the scatterlist in request_buffer instead
of the memory region.
This is fixed by using tw_transfer_internal() to transfer correctly to
the scatterlist.
Acked-by: adam radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
DVB USB remotes do not support changing keycode maps but set
input_dev->keycodesize and input_dev->keycodemax without setting
input_dev->keycode. This causes kernel oops when user tries to
look up (or change) current keymap.
While the proper fix would be to make remotes handle keymap changes
we'll just remove keycodemax and keycodesize initialization so
EVIOCGKEYCODE and EVIOCSKEYCODE will simply return -EINVAL.
http://bugzilla.kernel.org/show_bug.cgi?id=8312
Signed-off-by: olaf.kirch@oracle.com
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
