Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
Don't statically allocate struct device's in modules, and shut the
warning up with an empty release() function. There's a reason that
warning is there and that's not for people to hide in this way. It's
there to persuade people to use the correct APIs to allocate platform
devices.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace some instances of of_irq_map_one()/irq_create_of_mapping() and
of_irq_to_resource() by the simpler equivalent irq_of_parse_and_map().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: resolved conflicts with core code renames]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Each call to the co-processor, with exception of the last call, needs to
send data that is multiple of block size. As consequence, any remaining
data is kept in the internal NX context.
This patch fixes a bug in the driver that causes it to save incorrect
data into the context when data is bigger than the block size.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The NX CGM implementation doesn't support zero length messages and the
current implementation has two flaws:
- When the input data length is zero, it ignores the associated data.
- Even when both lengths are zero, it uses the Crypto API to encrypt a
zeroed block using ctr(aes) and because of this it allocates a new
transformation and sets the key for this new tfm. Both operations are
intended to be used only in user context, while the cryptographic
operations can be called in both user and softirq contexts.
This patch replaces the nested Crypto API use and adds two special
cases:
- When input data and associated data lengths are zero: it uses NX ECB
mode to emulate the encryption of a zeroed block using ctr(aes).
- When input data is zero and associated data is available: it uses NX
GMAC mode to calculate the associated data MAC.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The NX XCBC implementation doesn't support zero length messages and
because of that NX is currently returning a hard-coded hash for zero
length messages. However this approach is incorrect since the hash value
also depends on which key is used.
This patch removes the hard-coded hash and replace it with an
implementation based on the RFC 3566 using ECB.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the nx-aes-gcm implementation to perform several
hyper calls if needed in order to always respect the length limits for
scatter/gather lists.
Two different limits are considered:
- "ibm,max-sg-len": maximum number of bytes of each scatter/gather
list.
- "ibm,max-sync-cop":
- The total number of bytes that a scatter/gather list can hold.
- The maximum number of elements that a scatter/gather list can have.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the nx-aes-ctr implementation to perform several
hyper calls if needed in order to always respect the length limits for
scatter/gather lists.
Two different limits are considered:
- "ibm,max-sg-len": maximum number of bytes of each scatter/gather
list.
- "ibm,max-sync-cop":
- The total number of bytes that a scatter/gather list can hold.
- The maximum number of elements that a scatter/gather list can have.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the nx-aes-cbc implementation to perform several
hyper calls if needed in order to always respect the length limits for
scatter/gather lists.
Two different limits are considered:
- "ibm,max-sg-len": maximum number of bytes of each scatter/gather
list.
- "ibm,max-sync-cop":
- The total number of bytes that a scatter/gather list can hold.
- The maximum number of elements that a scatter/gather list can have.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the nx-aes-ecb implementation to perform several
hyper calls if needed in order to always respect the length limits for
scatter/gather lists.
Two different limits are considered:
- "ibm,max-sg-len": maximum number of bytes of each scatter/gather
list.
- "ibm,max-sync-cop":
- The total number of bytes that a scatter/gather list can hold.
- The maximum number of elements that a scatter/gather list can have.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch includes one more parameter to nx_build_sg_lists() to skip
the given number of bytes from beginning of each sg list.
This is needed in order to implement the fixes for the AES modes to make
them able to process larger chunks of data.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Each cycle of SHA512 operates on 32 data words where as
SHA256 operates on 16 data words. This needs to be updated
while configuring DMA channels. Doing the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For writing input buffer into DATA_IN register current driver
has the following state machine:
-> if input buffer < 9 : use fallback driver
-> else if input buffer < block size : Copy input buffer into data_in regs
-> else use dma transfer.
In cases where requesting for DMA channels fails for some reason,
or channel numbers are not provided in DT or platform data, probe
also fails. Instead of returning from driver use cpu polling mode.
In this mode processor polls on INPUT_READY bit and writes data into
data_in regs when it equals 1. This operation is repeated until the
length of message.
Now the state machine looks like:
-> if input buffer < 9 : use fallback driver
-> else if input buffer < block size : Copy input buffer into data_in regs
-> else if dma enabled: use dma transfer
else use cpu polling mode.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The bug here is that:
while (eng_busy & (!icq_empty) & dma_busy)
is never true because it's using bitwise instead of logical ANDs. The
other bitwise AND conditions work as intended but I changed them as well
for consistency.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is a typo here. "dev->hw_link[]" is an array, not a pointer, so
the check is nonsense. We should be checking recently allocated
"dev->hw_link[0]" instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For AM437x SoC, ARCH_OMAP2 and ARCH_OMAP3 is not enabled in the defconfig. We
follow same thing as SHA driver, and add depends on ARCH_OMAP2PLUS so that the
config is selectable for AES driver on AM437x SoC builds.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
