Add basic support for the System Power Management Interface (SPMI) bus.
This is a simple implementation which only implements register accesses
via the Extended Register Read/Write Long commands.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If called early enough, regmap_debugfs_init causes a crash, if the
fs subsystem does not have its mount cache created yet. Even if this
would work, the root node for the regmap debugfs is still missing,
thus postpone the regmap_debugfs_init in this case until the root
node is created. A special regmap_debugfs_early list is created for
this purpose which is parsed later in the boot.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
clear the status bit if the mask register doesn't prevent
the chip level irq from being asserted
OR in the following sequence, there will be irq storm happens:
1) interrupt is triggered;
2) another thread disables it(the mask bit is set);
3) _Then_ the interrupt thread is not ACKed(the status bit is not cleared),
and it's ignored;
4) if the irq is still asserted because of the uncleared status bit,
the irq storm happens;
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Extend the interface for async I/O by allowing the value buffer to be
omitted and sending the value as part of the register buffer, minimising
the number of separate hardware operations required.
Signed-off-by: Mark Brown <broonie@linaro.org>
If the value is zero then assume it has been included in the register data
and don't send anything, minimising the number of interactions with the
hardware.
Signed-off-by: Mark Brown <broonie@linaro.org>
New API regmap_multi_reg_write() is defined that allows a set of reg,val
pairs to be written to a I2C client device as one block transfer from the
point of view of a single I2C master system.
A simple demonstration implementation is included that just splits the
block write request into a sequence of single register writes.
The implementation will be modified later to support those I2C clients
that implement the alternative non-standard MULTIWRITE block write mode
so to achieve a single I2C transfer that will be atomic even in multiple
I2C master systems.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Try to speed up I/O a little by not synchronising until we are finished
scheduling writes. A brief survey of existing users suggests we have none
that would currently benefit from an async cache sync.
Signed-off-by: Mark Brown <broonie@linaro.org>
When regmap_bulk_write() is called with the map->use_single_rw flag set
an immediate mutex deadlock happens because regmap_raw_write() is called
after obtaining the mutex and regmap_raw_write() itself then tries to
obtain the mutex as well.
It is obvious that no one other than myself tried it with a real device.
I did, but only for the purposes of an experiment and demonstration.
But even if this situation will never ever happen with a real device, it
is a bug and therefore should be fixed.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make it easier for drivers to include single register writes in
asynchronous sequences by providing async versions of the write
and update bits operations. The update bits operations are only
likely to be effective when used with devices that have caches
but this is common enough to be useful.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than passing a flag around through the entire call stack store it
in the regmap struct and read it when required. This minimises the
visibility of the feature through the API, minimising the code updates
needed to use it more widely.
Signed-off-by: Mark Brown <broonie@linaro.org>
Since it is quite common for single register raw or async writes to be
generated by rbtree cache syncs or firmware downloads and essentially all
hardware will be faster with only a single transfer optimise this case by
copying single values into the internal scratch buffer before sending.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than allocating and deallocating the structures used to manage async
transfers each time we do one keep the structures around as long as the
regmap is around. This should provide a small performance improvement.
Signed-off-by: Mark Brown <broonie@linaro.org>
Current Linux kernel is supporting regmap_field method
and it is very useful feature.
It needs one regmap_filed for one register access.
OTOH, there is multi port device which
has many same registers in the market.
The difference for each register access is
only its address offset.
Current API needs many regmap_field for such device,
but it is not good.
This patch adds new regmap_fileds API which can care
about multi port/offset access via regmap.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current regmap_field is supporting read/write functions.
This patch adds new update_bits function for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
Pull regmap updates from Mark Brown:
"A quiet release for regmap, some cleanups, fixes and:
- Improved node coalescing for rbtree, reducing memory usage and
improving performance during syncs.
- Support for registering multiple register patches.
- A quirk for handling interrupts that need to be clear when masked
in regmap-irq"
* tag 'regmap-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: rbtree: Make cache_present bitmap per node
regmap: rbtree: Reduce number of nodes, take 2
regmap: rbtree: Simplify adjacent node look-up
regmap: debugfs: Fix continued read from registers file
regcache-rbtree: Fix reg_stride != 1
regmap: Allow multiple patches to be registered
regmap: regcache: allow read-only regs to be cached
regmap: fix regcache_reg_present() for empty cache
regmap: core: allow a virtual range to cover its own data window
regmap: irq: document mask/wake_invert flags
regmap: irq: make flags bool and put them in a bitfield
regmap: irq: Allow to acknowledge masked interrupts during initialization
regmap: Provide __acquires/__releases annotations
