Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Correct the comment above the definition of TCM_MAX_COMMAND_SIZE.
A quote from Christoph:
There aren't any legacy issues, we just decided to handle >
16 byte CDBs in the slow path.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
It seems like we only care if a transport is passthrough or not. Convert
transport_type to a flags field and replace TRANSPORT_PLUGIN_* with a
flag, TRANSPORT_FLAG_PASSTHROUGH.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Aside from whether they handle BIDI ops or not, parsing of the CDB by
kernel and user SCSI passthrough modules should be identical. Move this
into a new passthrough_parse_cdb() and call it from tcm-pscsi and tcm-user.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is just one configfs subsystem in the target code, so we might as
well add two helpers to reference / unreference it from the core code
instead of passing pointers to it around.
This fixes a regression introduced for v4.1-rc1 with commit 9ac8928e6,
where configfs_depend_item() callers using se_tpg_tfo->tf_subsys would
fail, because the assignment from the original target_core_subsystem[]
is no longer happening at target_register_template() time.
(Fix target_core_exit_configfs pointer dereference - Sagi)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity in target land the last months.
The highlights include:
- Convert fabric drivers tree-wide to target_register_template() (hch
+ bart)
- iser-target hardening fixes + v1.0 improvements (sagi)
- Convert iscsi_thread_set usage to kthread.h + kill
iscsi_target_tq.c (sagi + nab)
- Add support for T10-PI WRITE_STRIP + READ_INSERT operation (mkp +
sagi + nab)
- DIF fixes for CONFIG_DEBUG_SG=y + UNMAP file emulation (akinobu +
sagi + mkp)
- Extended TCMU ABI v2 for future BIDI + DIF support (andy + ilias)
- Fix COMPARE_AND_WRITE handling for NO_ALLLOC drivers (hch + nab)
Thanks to everyone who contributed this round with new features,
bug-reports, fixes, cleanups and improvements.
Looking forward, it's currently shaping up to be a busy v4.2 as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (69 commits)
target: Put TCMU under a new config option
target: Version 2 of TCMU ABI
target: fix tcm_mod_builder.py
target/file: Fix UNMAP with DIF protection support
target/file: Fix SG table for prot_buf initialization
target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabled
target: Make core_tmr_abort_task() skip TMFs
target/sbc: Update sbc_dif_generate pr_debug output
target/sbc: Make internal DIF emulation honor ->prot_checks
target/sbc: Return INVALID_CDB_FIELD if DIF + sess_prot_type disabled
target: Ensure sess_prot_type is saved across session restart
target/rd: Don't pass incomplete scatterlist entries to sbc_dif_verify_*
target: Remove the unused flag SCF_ACK_KREF
target: Fix two sparse warnings
target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handling
target: simplify the target template registration API
target: simplify target_xcopy_init_pt_lun
target: remove the unused SCF_CMD_XCOPY_PASSTHROUGH flag
target/rd: reduce code duplication in rd_execute_rw()
tcm_loop: fixup tpgt string to integer conversion
...
The following incremental patch saves the current sess_prot_type into
se_node_acl, and will always reset sess_prot_type if a previous saved
value exists. So the PI setting for the fabric's session with backend
devices not supporting PI is persistent across session restart.
(Fix se_node_acl dereference for discovery sessions - DanCarpenter)
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The flag SCF_ACK_KREF is only set but never tested. Hence remove
this flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug for COMPARE_AND_WRITE handling with
fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC.
It adds the missing allocation for cmd->t_bidi_data_sg within
transport_generic_new_cmd() that is used by COMPARE_AND_WRITE
for the initial READ payload, even if the fabric is already
providing a pre-allocated buffer for cmd->t_data_sg.
Also, fix zero-length COMPARE_AND_WRITE handling within the
compare_and_write_callback() and target_complete_ok_work()
to queue the response, skipping the initial READ.
This fixes COMPARE_AND_WRITE emulation with loopback, vhost,
and xen-backend fabric drivers using SG_TO_MEM_NOALLOC.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of calling target_fabric_configfs_init() +
target_fabric_configfs_register() / target_fabric_configfs_deregister()
target_fabric_configfs_free() from every target driver, rewrite the API
so that we have simple register/unregister functions that operate on
a const operations vector.
This patch also fixes a memory leak in several target drivers. Several
target drivers namely called target_fabric_configfs_deregister()
without calling target_fabric_configfs_free().
A large part of this patch is based on earlier changes from
Bart Van Assche <bart.vanassche@sandisk.com>.
(v2: Add a new TF_CIT_SETUP_DRV macro so that the core configfs code
can declare attributes as either core only or for drivers)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates iscsi/iser-target to add a new fabric_prot_type
TPG attribute for iser-target, used for controlling LLD level
protection into LIO when the backend device does not support T10-PI.
This is required for ib_isert to enable WRITE_STRIP + READ_INSERT
hardware offloads.
It's disabled by default and controls which se_sesion->sess_prot_type
are set at iscsi_target_locate_portal() session registration time.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new target_core_fabric_ops callback for allowing fabric
drivers to expose a TPG attribute for signaling when a T10-PI protected
fabric wants to function with an un-protected device without T10-PI.
This specifically is to allow LIO to perform WRITE_STRIP + READ_INSERT
operations when functioning with non T10-PI enabled devices, seperate
from any available hw offloads the fabric supports.
This is done using a new se_sess->sess_prot_type that is set at fabric
session creation time based upon the TPG attribute. It currently cannot
be changed for individual sessions after initial creation.
Also, update existing target_core_sbc.c code to honor sess_prot_type when
setting up cmd->prot_op + cmd->prot_type assignments.
(Add unlikely and !! boolean conversion in sbc_check_prot - Sagi)
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that iscsi_conn allocates new [rx,tx] threads using kthread.h
primitives on the fly, and kthread_stop() is called directly during
connection shutdown, it's time to go ahead and drop iscsi_target_tq.c
legacy code.
The use of multiple struct completion in iscsi_activate_thread_set()
has been proven to cause issues during repeated iser login/logout.
Tested-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts iscsi-target code to use modern kthread.h API
callers for creating RX/TX threads for each new iscsi_conn descriptor,
and releasing associated RX/TX threads during connection shutdown.
This is done using iscsit_start_kthreads() -> kthread_run() to start
new kthreads from within iscsi_post_login_handler(), and invoking
kthread_stop() from existing iscsit_close_connection() code.
Also, convert iscsit_logout_post_handler_closesession() code to use
cmpxchg when determing when iscsit_cause_connection_reinstatement()
needs to sleep waiting for completion.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Tested-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A check that rejects a CDB with FUA bit set if no write cache is
emulated was added by the following commit:
fde9f50 target: Add sanity checks for DPO/FUA bit usage
The condition is as follows:
if (!dev->dev_attrib.emulate_fua_write ||
!dev->dev_attrib.emulate_write_cache)
However, this check is wrong if the backend device supports WCE but
"emulate_write_cache" is disabled.
This patch uses se_dev_check_wce() (previously named
spc_check_dev_wce) to invoke transport->get_write_cache() if the
device has a write cache or check the "emulate_write_cache" attribute
otherwise.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new helper function that can be used by fabric driver
TPG attributes for dumping the list of active sessions with a dynamically
generated se_node_acl. (generate_node_acl=1).
It prints one se_node_acl->initiatorname per line, up to PAGE_SIZE which
is due to the current limitiation of single page attribute output within
sysfs and configfs code.
Note that if a session is referencing a explicit NodeACL, the InitiatorName
will not appear within dynamic_sessions output.
Reported-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Update vhost-scsi to support F_ANY_LAYOUT using mm/iov_iter.c
logic, and signal VERSION_1 support (MST + Viro + nab)
- Fix iscsi/iser-target to remove problematic active_ts_set usage
(Gavin Guo)
- Update iscsi/iser-target to support multi-sequence sendtargets
(Sagi)
- Fix original PR_APTPL_BUF_LEN 8k size limitation (Martin Svec)
- Add missing WRITE_SAME end-of-device sanity check (Bart)
- Check for LBA + sectors wrap-around in sbc_parse_cdb() (nab)
- Other various minor SPC/SBC compliance fixes based upon Ronnie
Sahlberg test suite (nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (32 commits)
target: Set LBPWS10 bit in Logical Block Provisioning EVPD
target: Fail UNMAP when emulate_tpu=0
target: Fail WRITE_SAME w/ UNMAP=1 when emulate_tpws=0
target: Add sanity checks for DPO/FUA bit usage
target: Perform PROTECT sanity checks for WRITE_SAME
target: Fail I/O with PROTECT bit when protection is unsupported
target: Check for LBA + sectors wrap-around in sbc_parse_cdb
target: Add missing WRITE_SAME end-of-device sanity check
iscsi-target: Avoid IN_LOGOUT failure case for iser-target
target: Fix PR_APTPL_BUF_LEN buffer size limitation
iscsi-target: Drop problematic active_ts_list usage
iscsi/iser-target: Support multi-sequence sendtargets text response
iser-target: Remove duplicate function names
vhost/scsi: potential memory corruption
vhost/scsi: Global tcm_vhost -> vhost_scsi rename
vhost/scsi: Drop left-over scsi_tcq.h include
vhost/scsi: Set VIRTIO_F_ANY_LAYOUT + VIRTIO_F_VERSION_1 feature bits
vhost/scsi: Add ANY_LAYOUT support in vhost_scsi_handle_vq
vhost/scsi: Add ANY_LAYOUT iov -> sgl mapping prerequisites
vhost/scsi: Change vhost_scsi_map_to_sgl to accept iov ptr + len
...
This patch addresses the original PR_APTPL_BUF_LEN = 8k limitiation
for write-out of PR APTPL metadata that Martin has recently been
running into.
It changes core_scsi3_update_and_write_aptpl() to use vzalloc'ed
memory instead of kzalloc, and increases the default hardcoded
length to 256k.
It also adds logic in core_scsi3_update_and_write_aptpl() to double
the original length upon core_scsi3_update_aptpl_buf() failure, and
retries until the vzalloc'ed buffer is large enough to accommodate
the outgoing APTPL metadata.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case sendtargets response is larger than initiator MRDSL, we
send a partial sendtargets response (setting F=0, C=1, TTT!=0xffffffff),
accept a consecutive empty text message and send the rest of the payload.
In case we are done, we set F=1, C=0, TTT=0xffffffff.
We do that by storing the sendtargets response bytes done under
the session.
This patch also makes iscsit_find_cmd_from_itt public for isert.
(Re-add cmd->maxcmdsn_inc and clear in iscsit_build_text_rsp - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Seems strange to see in include/target/iscsi/iscsi_transport.h:
include "../../../drivers/target/iscsi/iscsi_target_core.h"
Move it to it's natural location.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that fabric_max_sectors is no longer used to enforce the maximum
I/O size, go ahead and drop it's left-over usage in target-core and
associated backend drivers.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI update from James Bottomley:
"This is a much shorter set of patches that were on the go but didn't
make it in to the early pull request for the merge window. It's
really a set of bug fixes plus some final cleanup work on the new tag
queue API"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
storvsc: ring buffer failures may result in I/O freeze
ipr: set scsi_level correctly for disk arrays
ipr: add support for async scanning to speed up boot
scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
scsi_debug: take sdebug_host_list_lock when changing capacity
scsi_debug: improve driver description in Kconfig
scsi_debug: fix compare and write errors
qla2xxx: fix race in handling rport deletion during recovery causes panic
scsi: blacklist RSOC for Microsoft iSCSI target devices
scsi: fix random memory corruption with scsi-mq + T10 PI
Revert "[SCSI] mpt3sas: Remove phys on topology change"
Revert "[SCSI] mpt2sas: Remove phys on topology change."
esas2r: Correct typos of "validate" in a comment
fc: FCP_PTA_SIMPLE is 0
ibmvfc: remove unused tag variable
scsi: remove MSG_*_TAG defines
scsi: remove scsi_set_tag_type
scsi: remove scsi_get_tag_type
scsi: never drop to untagged mode during queue ramp down
scsi: remove ->change_queue_type method
