Keycodes in 248 - 254 range were reserved for special needs (scrolling)
of atkbd driver. Now that the driver has been switched to use unsigned
short keycodes instead of unsigned char we can release this range back
into pull. We keep code 255 (ATKBD_KEY_NULL) reserved since users may
have been using it to silence keys they do not care about since atkbd
silently drops scancodes mapped to this keycode.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Update the Kconfig entry for the sh_keysc driver to
enable build on SH-Mobile ARM platforms.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add mode 6 support to the sh_keysc driver. Also update the KYOUTDR mask
value to include all 16 register bits.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use bitmaps instead of using 32-bit integers to keep track of the key
states. With this change in place the driver supports key pads with
more than 32 keys.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Update the sh_keysc driver to factor out the register access functions
sh_keysc_read(), sh_keysc_write() together with sh_keysc_level_mode().
This makes the code a bit easier to follow.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Provided that now keyboards on these devices are fully supported by
generic GPIO based matrix keypad driver, mark these hardcoded and
difficult to maintain drivers as deprecated.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now gpio-keys input driver exports 4 new attributes to userland through
sysfs:
/sys/devices/platform/gpio-keys/keys [ro]
/sys/devices/platform/gpio-keys/switches [ro]
/sys/devices/platform/gpio-keys/disabled_keys [rw]
/sys/devices/platform/gpio-keys/disables_switches [rw]
With these attributes, userland program can read which keys and
switches can be disabled and then disable/enable them as needed.
Keys and switches are exported as stringified bitmap of codes
(keycodes or switch codes). For example keys 15, 89, 100, 101,
102 are exported as: '15,89,100-102'.
Description of the attributes:
keys - bitmap of keys which can be disabled
switches - bitmap of switches which can be disabled
disabled_keys - bitmap of currently disabled keys
(bit 1 means disabled, 0 enabled)
disabled_switches - bitmap of currently disabled switches
(bit 1 means disabled, 0 enabled)
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The IMX family of Application Processors is shipped with a Keypad Port
supported by this driver.
The peripheral can control up to an 8x8 matrix key pad where all the
scanning is done via software. The hardware provides two interrupts:
one for key presses (KDI) and one for all key releases (KRI). There is
also a simple circuit for glitch reduction (said for synchronization)
made by two series of 3 D-latches clocked by the keypad-clock that
stabilize the interrupts sources. KDI and KRI are fired only if the
respective conditions are maintained for at last 4 keypad-clock cycle.
Since those circuits are poor for a correct debounce process (the
keypad-clock frequency is 32K and bounces longer than 94us are not
masked) the driver, when an interrupt arrives, samples the matrix
with a period of 10ms until the readins are stable for
IMX_KEYPAD_SCANS_FOR_STABILITY times (currently set at 3). After
getting stable result appropriate events are sent through the input
stack.
If some keys are maintained pressed, the driver continues to scan
the matrix with a longer period (60ms) to catch possible multiple
key presses without overloading the cpu. This process ends when all
keys are released.
This driver is tested to build in kernel or as a module and follow
the specification of Freescale Application processors:
i.MX25 i.MX27 i.MX31 i.MX35 i.MX51 especially tested on i.MX31.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add Mode 4 and Mode 5 support to the SH_KEYSC driver. These modes allow
slightly larger key pad matrixes.
While at it, make use of resource_size().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The ADP5587 is quite similar to the ADP5588 but features a greater I/O
voltage range and lacks the Dual Light Sensor Interface. This new part
is also supported by this driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sentelic - fix left/right horizontal scroll mapping
Input: pmouse - move Sentelic probe down the list
Input: add compat support for sysfs and /proc capabilities output
Input: i8042 - add Dritek quirk for Acer Aspire 5610.
Input: xbox - do not use GFP_KERNEL under spinlock
Input: psmouse - fix Synaptics detection when protocol is disabled
Input: bcm5974 - report ABS_MT events
Input: davinci_keyscan - add device_enable method to platform data
Input: evdev - be less aggressive about sending SIGIO notifies
Input: atkbd - fix canceling event_work in disconnect
Input: serio - fix potential deadlock when unbinding drivers
Input: gf2k - fix &&/|| confusion in gf2k_connect()
Use struct matrix_keymap_data to supply the keymap from the platform code
and matrix_keypad_build_keymap() to initialize the keymap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The id_table field of the struct i2c_driver is defined as constant
in <linux/i2c.h> so it makes sense to mark the initialization data also
constant.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
dev_err(), dev_warn() and dev_dbg() ensure consistency in driver messages.
Also switch to using bool where appropriate and fix some formatting issues.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a function pointer in the platform data of the DaVinci Keyscan driver
called device_enable, in order to perform board specific actions when
the device is initialized, like setup the PINMUX configuration.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to first unregister input device and only then cancel event work
since events can arrive (and cause event work to get scheduled again)
until input_unregister_device() returns.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
sysfs_remove_group() waits for sysfs attributes to be removed, therefore
we do not need to worry about driver-specific attributes being accessed
after driver has been detached from the device. In fact, attempts to take
serio->drv_mutex in attribute methods may lead to the following deadlock:
sysfs_read_file()
fill_read_buffer()
sysfs_get_active_two()
psmouse_attr_show_helper()
serio_pin_driver()
serio_disconnect_driver()
mutex_lock(&serio->drv_mutex);
<--------> mutex_lock(&serio_drv_mutex);
psmouse_disconnect()
sysfs_remove_group(... psmouse_attr_group);
....
sysfs_deactivate();
wait_for_completion();
Fix this by removing calls to serio_[un]pin_driver() and functions themselves
and using driver-private mutexes to serialize access to attribute's set()
methods that may change device state.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: iforce - wait for command completion when closing the device
Input: twl4030-pwrbutton - switch to using threaded IRQ
Input: twl4030_keypad - switch to using threaded IRQ
Input: lifebook - add CONFIG_DMI dependency
Input: wistron - fix test for CONFIG_PM
Input: psmouse - fix compile warning in hgpk module
Input: matrix-keypad - handle cases when GPIOs can't be wakeup sources
Input: iforce - fix oops on device disconnect
Input: ff-memless - add notion of direction to for rumble effects
Input: ff-memless - another fix for signed to unsigned overflow
Input: ff-memless - start playing FF effects immediately
Input: serio - do not mark kseriod freezable anymore
Input: speed up suspend/shutdown for PS/2 mice and keyboards
On certain boards not all GPIOs may be used as wakeup sources, in which
case some of enable_irq_wake() calls will fail. On resume calling
disable_irq_wake() will warn about unbalanced IRQ wake disable.
Solve this by checking whether enable_irq_wake() succeeded or not and
no not call disable_irq_wake() for these GPIOs/IRQs that have not been
enabled.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of doing full-blown reset while suspending or shutting down
the box use lighter form of reset that should take less time.
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (22 commits)
Input: ALPS - add interleaved protocol support (Dell E6x00 series)
Input: keyboard - don't override beep with a bell
Input: altera_ps2 - fix test of unsigned in altera_ps2_probe()
Input: add mc13783 touchscreen driver
Input: ep93xx_keypad - update driver to new core support
Input: wacom - separate pen from express keys on Graphire
Input: wacom - add defines for data packet report IDs
Input: wacom - add support for new LCD tablets
Input: wacom - add defines for packet lengths of various devices
Input: wacom - ensure the device is initialized properly upon resume
Input: at32psif - do not sleep in atomic context
Input: i8042 - add Gigabyte M1022M to the noloop list
Input: i8042 - allow installing platform filters for incoming data
Input: i8042 - fix locking in interrupt routine
Input: ALPS - do not set REL_X/REL_Y capabilities on the touchpad
Input: document use of input_event() function
Input: sa1111ps2 - annotate probe() and remove() methods
Input: ambakmi - annotate probe() and remove() methods
Input: gscps2 - fix probe() and remove() annotations
Input: altera_ps2 - add annotations to probe and remove methods
...
This driver was merged before the ep93xx core support was added
for the keypad clock and acquiring/releasing the necessary gpio's.
Now that the proper support is in the ep93xx core this driver
needs to be updated to work correctly.
Summary of changes:
1) Remove some unused members from the platform data.
2) Remove the custom KEY macro and use the ones available in
<linux/input/matrix_keypad.h>
3) Remove the keypad_{readl/writel} macros and just use
__raw_{readl/writel} directly.
4) Update the clk_set_rate() call to work with the core support.
5) Cleanup the probe routine and remove some unneeded messages.
6) Use the ep93xx core functions to acquire and release the gpio's.
7) Fix the clk_get() call to get the keypad clock.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
