syscall_nr is presently defined as unsigned in the SH-5 pt_regs,
while the syscall restarting code wants it to be signed. Fix this
up, and bring it in line with the other SH parts.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: sh7785lcr: Map whole PCI address space.
sh: Fix up DSP context save/restore.
sh: Fix up number of on-chip DMA channels on SH7091.
sh: update defconfigs.
sh: Kill off broken direct-mapped cache mode.
sh: Wire up ARCH_HAS_DEFAULT_IDLE for cpuidle.
sh: Add a command line option for disabling I/O trapping.
sh: Select ARCH_HIBERNATION_POSSIBLE.
sh: migor: Fix up CEU use flags.
input: migor_ts: add wakeup support
rtc: rtc-sh: use set_irq_wake()
input: sh_keysc: use enable/disable_irq_wake()
sh: intc: set_irq_wake() support
sh: intc: install enable, disable and shutdown callbacks
clocksource: sh_cmt: use remove_irq() and remove clockevent workaround
sh: ap325 and Migo-R use new sh_mobile_ceu_info flags
sh: Fix up -Wformat-security whining.
sh: ap325rxa: Add ov772x support, again.
sh: Sanitize asm/mmu.h for assembly use.
sh: Tidy up sh7786 pinmux table.
...
There were a number of issues with the DSP context save/restore code,
mostly left-over relics from when it was introduced on SH3-DSP with
little follow-up testing, resulting in things like task_pt_dspregs()
referencing incorrect state on the stack.
This follows the MIPS convention of tracking the DSP state in the
thread_struct and handling the state save/restore in switch_to() and
finish_arch_switch() respectively. The regset interface is also updated,
which allows us to finally be rid of task_pt_dspregs() and the special
cased task_pt_regs().
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
cpuidle wants ARCH_HAS_DEFAULT_IDLE defined in order to use the
default idle loop. So, make it accessible and enable it for all
sh machines.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the ifndef __ASSEMBLY__ preprocessor to allow the
defines in the file to be used also in assembly code.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Everyone defines it, and only one person uses it
(arch/mips/sgi-ip27/ip27-nmi.c). So just open code it there.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-mips@linux-mips.org
Rework the hd64461 demuxer code to fix the HD64461 level-triggered
interrupts handling, using handle_level_irq() as needed.
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the ARM change from Aaro Koskinen:
When unmapping N pages (e.g. shared memory) the amount of TLB
flushes done can be (N*PAGE_SIZE/ZAP_BLOCK_SIZE)*N although it
should be N at maximum. With PREEMPT kernel ZAP_BLOCK_SIZE is 8
pages, so there is a noticeable performance penalty when
unmapping a large VMA and the system is spending its time in
flush_tlb_range().
The problem is that tlb_end_vma() is always flushing the full VMA
range. The subrange that needs to be flushed can be calculated by
tlb_remove_tlb_entry(). This approach was suggested by Hugh
Dickins, and is also used by other arches.
The speed increase is roughly 3x for 8M mappings and for larger
mappings even more.
Bits and peices are taken from the ARM patch as well as the existing
arch/um implementation that is quite similar.
The end result is a significant reduction in both partial and full TLB
flushes initiated through flush_tlb_range().
At the same time, the nommu implementation was broken, had a superfluous
cache flush, and subsequently would have triggered a BUG_ON() if a
code-path had triggered it. Tidy this up for correctness and provide a
nopped-out implementation there.
More background on the initial discussion can be found at:
http://marc.info/?t=123609820900002&r=1&w=2http://marc.info/?t=123660375800003&r=1&w=2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for extended ASIDs (up to 16-bits) on newer SH-X3 cores
that implement the PTAEX register and respective functionality. Presently
only the 65nm SH7786 (90nm only supports legacy 8-bit ASIDs).
The main change is in how the PTE is written out when loading the entry
in to the TLB, as well as in how the TLB entry is selectively flushed.
While SH-X2 extended mode splits out the memory-mapped U and I-TLB data
arrays for extra bits, extended ASID mode splits out the address arrays.
While we don't use the memory-mapped data array access, the address
array accesses are necessary for selective TLB flushes, so these are
implemented newly and replace the generic SH-4 implementation.
With this, TLB flushes in switch_mm() are almost non-existent on newer
parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.
To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds DMA support for newer SH-4A CPUs, particularly SH7763/64/80/85.
This also enables multi IRQ support for platforms that have multiple
vectors bound to the same IRQ source.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.
To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.
The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.
Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH-3 does not support 'pref'-based prefetching, only SH-2A and SH-4A
parts do. Remove SH-3 from the list.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
