This switches the driver to using managed resources to simplify error
handling and to do away with remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We can annonate the suspend/resume functions with '__maybe_unused' and get
rid of the ifdef, which makes the code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When a kernel has CONFIG_PM=y and CONFIG_PM_SLEEP=n the following warnings are
seen:
drivers/input/touchscreen/mcs5000_ts.c:252:12: warning: 'mcs5000_ts_suspend' defined but not used [-Wunused-function]
static int mcs5000_ts_suspend(struct device *dev)
^
drivers/input/touchscreen/mcs5000_ts.c:262:12: warning: 'mcs5000_ts_resume' defined but not used [-Wunused-function]
static int mcs5000_ts_resume(struct device *dev)
Protect the suspend/resume functions with CONFIG_PM_SLEEP in order to fix these
build warnings.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Input device must be released(input_free_device) when ads7846_probe_dt
fails. This fixes the same by releasing resources on failure.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By writing zero to both the active and idle cycle times the maXTouch device
is put into a deep sleep mode when it consumes minimal power. It is
unnecessary to change the configuration of any other objects (for example
to disable T9 touchscreen).
It is counterproductive to reset the chip on resume, it will result in a
long delay. However it is necessary to issue a calibrate command after the
chip has spent any time in deep sleep.
This patch also deals with the situation where the power configuration is
zero on probe, which would mean that the device never wakes up to execute
commands.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Provide device tree support and binding information. Also provide support
for a new chip "pixcir_tangoc".
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some variants of the Pixcir touch controller support up to 5 simultaneous
fingers and hardware tracking IDs. Prepare the driver for that.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wire up open/close so we do not try to send events until someone uses them;
this also allows us to remove micro_ts_remove() and rely fully on managed
resources.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds a driver for the touchscreen connected to the Atmel
microcontroller on the iPAQ h3xxx series.
Based on a driver from handhelds.org 2.6.21 kernel, written by Alessandro
GARDICH, with the bulk of the code for the new input architecture rewritten
by Dmitry Atamonow, and the final polish by Linus Walleij.
Signed-off-by: Alessandro GARDICH <gremlin@gremlin.it>
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
maXTouch chips allow the reading of multiple messages in a single I2C
transaction, which reduces bus overhead and improves performance/latency. The
number of messages available to be read is given by the value in the T44
object which is located directly before the T5 object.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The T5 object may have various sizes depending on the objects used on the
particular maXTouch chip and firmware version, therefore it can't be
hardcoded in the driver. Allocate a buffer on probe instead.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MXT device may be in bootloader mode on probe, due to:
1) APP CRC failure, either:
a) flash corruption
b) bad power or other intermittent problem while checking CRC
2) If the device has been reset 10 or more times without accessing comms
3) Warm probe, device was in bootloader mode already
This code attempts to recover from 1(b) and 3.
There is an additional complexity: we have to try two possible bootloader
addresses because the mapping is not one-to-one and we don't know the exact
model yet.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Later chips (for example mXT1664S) different mappings for bootloader
addresses. This means that we must look at the family ID to determine
which address to use.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the bootloader on the touchscreen controller fails to initialise the
firmware image, it stays in bootloader mode and reports a failure. It is
possible to reflash a working firmware image from this state.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By validating the checksum, we can identify if the configuration is
corrupt. In addition, this patch writes the configuration in a short
series of block writes rather than as many individual values.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The existing implementation which encodes the configuration as a binary
blob in platform data is unsatisfactory since it requires a kernel
recompile for the configuration to be changed, and it doesn't deal well
with firmware changes that move values around on the chip.
Atmel define an ASCII format for the configuration which can be exported
from their tools. This patch implements a parser for that format which
loads the configuration via the firmware loader and sends it to the MXT
chip.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Touchpads are pointers, so make sure to pass the correct values to
input_mt_report_pointer_emulation(). Without this, tap-to-click doesn't
work.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
