This patch adds hardware assisted scrolling. The code is based upon the
following investigation: https://parisc.wiki.kernel.org/index.php/NGLE#Blitter
A simple 'time ls -la /usr/bin' test shows 1.6x speed increase over soft
copy and 2.3x increase over FBINFO_READS_FAST (prefer soft copy over
screen redraw) on Artist framebuffer.
Signed-off-by: Alex Ivanov <lausgans@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Pull fbdev fix from Tomi Valkeinen:
"Fix display regression on TI AM4xxx boards"
* tag 'fbdev-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
OMAPDSS: fix probing if rfbi device is enabled
After the commit 736e60ddc2 ("OMAPDSS:
componentize omapdss") the dss core device will wait until all the
subdevices have been successfully probed. However, we don't have a
working driver for RFBI, so if RFBI device exists, omapdss will never
get probed.
All the .dtsi files set RFBI as disabled, except am4372.dtsi. This
causes omapdss probe to not finish on AM4 devices.
This patch makes omapdss driver skip adding rfbi device as a
subcomponent, solving the issue.
This should be reverted when we have a working RFBI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Felipe Balbi <balbi@ti.com>
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Pull fbdev updates from Tomi Valkeinen:
- ssd1307fb: various fixes and improvements, SSD1305 support
- use architecture agnostic functions instead of MTRR functions in
various fbdev drivers
- TI DRA7xx SoC display support (arch/arm/ side)
- OMAPDSS componentization to fix probing order issues
- OMAPDSS scaling fixes
- msm_fb: remove obsoleted driver
* tag 'fbdev-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (77 commits)
msm: msm_fb: Remove dead code
OMAPDSS: HDMI: wait for framedone when stopping video
OMAPDSS: HDMI4: fix error handling
OMAPDSS: DISPC: scaler debug print
OMAPDSS: DISPC: do only y decimation on OMAP3
OMAPDSS: DISPC: check if scaling setup failed
OMAPDSS: DISPC: fix 64 bit issue in 5-tap
OMAPDSS: DISPC: fix row_inc for OMAP3
OMAPDSS: DISPC: add check for scaling limits
OMAPDSS: DISPC: fix check_horiz_timing_omap3 args
OMAPDSS: DISPC: fix predecimation for YUV modes
OMAPDSS: DISPC: work-around for errata i631
OMAPDSS: simplify submodule reg/unreg code
OMAPDSS: componentize omapdss
OMAPDSS: reorder uninit calls
OMAPDSS: remove uses of __init/__exit
OMAPDSS: fix dss_init_ports error handling
OMAPDSS: refactor dss probe function
OMAPDSS: move 'dss_initialized' to dss driver
fbdev: propagate result of fb_videomode_from_videomode()
...
Add a "param_lock" mutex to each module, and update params.c to use
the correct built-in or module mutex while locking kernel params.
Remove the kparam_block_sysfs_r/w() macros, replace them with direct
calls to kernel_param_[un]lock(module).
The kernel param code currently uses a single mutex to protect
modification of any and all kernel params. While this generally works,
there is one specific problem with it; a module callback function
cannot safely load another module, i.e. with request_module() or even
with indirect calls such as crypto_has_alg(). If the module to be
loaded has any of its params configured (e.g. with a /etc/modprobe.d/*
config file), then the attempt will result in a deadlock between the
first module param callback waiting for modprobe, and modprobe trying to
lock the single kernel param mutex to set the new module's param.
This fixes that by using per-module mutexes, so that each individual module
is protected against concurrent changes in its own kernel params, but is
not blocked by changes to other module params. All built-in modules
continue to use the built-in mutex, since they will always be loaded at
runtime and references (e.g. request_module(), crypto_has_alg()) to them
will never cause load-time param changing.
This also simplifies the interface used by modules to block sysfs access
to their params; while there are currently functions to block and unblock
sysfs param access which are split up by read and write and expect a single
kernel param to be passed, their actual operation is identical and applies
to all params, not just the one passed to them; they simply lock and unlock
the global param mutex. They are replaced with direct calls to
kernel_param_[un]lock(THIS_MODULE), which locks THIS_MODULE's param_lock, or
if the module is built-in, it locks the built-in mutex.
Suggested-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
At the moment when HDMI video output is stopped, we just clear the
enable bit and return. While it's unclear if this can cause any issues,
I think it's still better to wait for FRAMEDONE interrupt after clearing
the enable bit so that we're sure the HDMI IP has finished.
As we don't have any ready-made irq handling for HDMI, and this only
needs to be done when disabling the HDMI output, this patch implements a
simple loop with sleep, polling the FRAMEDONE bit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Error handling in hdmi_power_on_full() is not correct, and could leave
resources unfreed.
Fix this by arranging the error labels correctly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current driver does both x and y decimation on OMAP3 DSS. Testing
shows that x decimation rarely works, leading to underflows.
The exact reason for this is unclear, as the underflows seem to happen
even with low pixel clock rates, and I would presume that if the DSS can
manage a display with 140MHz pixel clock, it could manage x decimation
with factor 2 with a low pixel clock (~30MHz).
So it is possible that there is a problem somewhere else, in memory
management, or DSS DMA, or similar. I have not found anything that would
help this.
So, to fix the downscaling scaling, this patch removes x decimation for
OMAP3. This will limit some of the more demanding downscaling scenarios,
but one could argue that using DSS to downscale such a large amount is
insane in the first place, as the produced image is rather bad quality.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DISPC's scaling code seems to presume that decimation always
succeeds, and so we always do find a suitable downscaling setup.
However, this is not the case, and the algorithm can fail.
When that happens, the code just proceeds with wrong results, causing
issues later.
Add the necessary checks to bail out if the scaling algorithm failed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DISPC driver uses 64 bit arithmetic to calculate the required clock
rate for scaling. The code does not seem to work correctly, and instead
calculates with 32 bit numbers, giving wrong result.
Fix the code by typecasting values to u64 first, so that the
calculations do happen in 64 bits.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
pixel_inc and row_inc work differently on OMAP2/3 and OMAP4+ DSS. On
OMAP2/3 DSS, the pixel_inc is _not_ added by the HW at the end of the
line, after the last pixel, whereas on OMAP4+ it is.
The driver currently works for OMAP4+, but does not handle OMAP2/3
correctly, which leads to tilted image when row_inc is used.
This patch adds a flag to DISPC driver so that the pixel_inc is added
when required.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP3/AM43xx some scaling factors cause underflows/synclosts. After
studying this, I found that sometimes the driver uses three-tap scaling
with downscaling factor smaller than x0.5. This causes issues, as x0.5
is the limit for three-tap scaling.
The driver has FEAT_PARAM_DOWNSCALE parameter, but that seems to be for
five-tap scaling, which allows scaling down to x0.25.
This patch adds checks for both horizontal and vertical scaling. For
horizontal the HW always uses 5 taps, so the limit is x0.25.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
After calculating the required decimation for scaling, the dispc driver
checks once more if the resulting configuration is valid by calling
check_horiz_timing_omap3().
Earlier calls to this function have correctly used in_width and
in_height as parameters, but the last call uses width and height. This
causes the driver to possibly reject scaling that would work.
This patch fixes the parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC needs even input buffer width for YUV modes. The DISPC driver
doesn't check this at the moment (although omapdrm does), but worse,
when DISPC driver does x predecimation the result may be uneven. This
causes sometimes sync losts, underflows, or just visual errors.
This patch makes DISPC driver return an error if the user gives uneven
input width for a YUV buffer. It also makes the input width even in case
of predecimation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Errata i631 description:
"When in YUV4:2:0 format in 1D burst, the DISPC DMA skips lines when
fetching Chroma sampling."
Workaround:
"If YUV4:2:0-1D burst is required: Set
DISPC_VIDp_ATTRIBUTES[22]DOUBLESTRIDE to 0x0 and
DISPC_VIDp_ATTRIBUTES[13:12]ROTATION to 0x1 or 0x3"
The description is somewhat confusing, but testing has shown that DSS
fetches extra rows from memory when using NV12 format in 1D mode. If the
memory after the framebuffer is inaccessible, this leads to OCP errors.
The driver always uses DOUBLESTRIDE=0 when using 1D mode, so we only
need to handle the ROTATION part.
The issue exist on all OMAP4 and OMAP5 based DSS IPs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that we are using components in omapdss, there's no need for
separate handling of dss and dispc driver init. Thus we can move the dss
and dispc init and unit func pointers to the lists we use for the other
dss submodules.
We can now also handle errors returned by the registration functions
properly: if registering a driver fails, we can stop processing and
return the error.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omapdss kernel module contains drivers for multiple devices, one for
each DSS submodule. The probing we have at the moment is a mess, and
doesn't give us proper deferred probing nor ensure that all the devices
are probed before omapfb/omapdrm start using omapdss.
This patch solves the mess by using the component system for DSS
submodules.
The changes to all DSS submodules (dispc, dpi, dsi, hdmi4/5, rfbi, sdi,
venc) are the same: probe & remove functions are changed to bind &
unbind, and new probe & remove functions are added which call
component_add/del.
The dss_core driver (dss.c) acts as a component master. Adding and
matching the components is simple: all dss device's child devices are
added as components.
However, we do have some dependencies between the drivers. The order in
which they should be probed is reflected by the list in core.c
(dss_output_drv_reg_funcs). The drivers are registered in that order,
which causes the components to be added in that order, which makes the
components to be bound in that order. This feels a bit fragile, and we
probably should improve the code to manage binds in random order.
However, for now, this works fine.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We have a list of function pointers to dss submodule uninit functions.
It makes sense to do the uninit in the reverse order to init, but that
is not currently the case.
This patch reorders the uninit calls to be the reverse of init order.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The following patches will add component handling to omapdss, improving
the handling of deferred probing. However, at the moment we're using
quite a lot of __inits and __exits in the driver, which prevent normal
dynamic probing and removal.
This patch removes most of the uses of __init and __exit, so that we can
register drivers after module init, and so that we can unregister
drivers even if the module is built-in.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The return value of dss_init_ports() is not handled at all, causing
crashes later if the call failed.
This patch adds the error handling, and we also move the call to a
slightly earlier place to make bailing out easier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
