Pull module_platform_driver replacement from Paul Gortmaker:
"Replace module_platform_driver with builtin_platform driver in non
modules.
We see an increasing number of non-modular drivers using
modular_driver() type register functions. There are several downsides
to letting this continue unchecked:
- The code can appear modular to a reader of the code, and they won't
know if the code really is modular without checking the Makefile
and Kconfig to see if compilation is governed by a bool or
tristate.
- Coders of drivers may be tempted to code up an __exit function that
is never used, just in order to satisfy the required three args of
the modular registration function.
- Non-modular code ends up including the <module.h> which increases
CPP overhead that they don't need.
- It hinders us from performing better separation of the module init
code and the generic init code.
So here we introduce similar macros for builtin drivers. Then we
convert builtin drivers (controlled by a bool Kconfig) by making the
following type of mapping:
module_platform_driver() ---> builtin_platform_driver()
module_platform_driver_probe() ---> builtin_platform_driver_probe().
The set of drivers that are converted here are just the ones that
showed up as relying on an implicit include of <module.h> during a
pending header cleanup. So we convert them here vs adding an include
of <module.h> to non-modular code to avoid compile fails. Additonal
conversions can be done asynchronously at any time.
Once again, an unused module_exit function that is removed here
appears in the diffstat as an outlier wrt all the other changes"
* tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver
drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver
drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver
drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver
drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver
drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver
platform_device: better support builtin boilerplate avoidance
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Caused by commit 843735b788 ("power: axp288_charger: axp288 charger
driver") from the battery tree interacting with commit 046050f6e6
("extcon: Update the prototype of extcon_register_notifier() with enum
extcon") from the extcon tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull USB updates from Greg KH:
"Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (175 commits)
usb: dwc3: Use ASCII space in Kconfig
usb: chipidea: add work-around for Marvell HSIC PHY startup
usb: chipidea: allow multiple instances to use default ci_default_pdata
dt-bindings: Consolidate ChipIdea USB ci13xxx bindings
phy: add Marvell HSIC 28nm PHY
phy: Add Marvell USB 2.0 OTG 28nm PHY
dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings
USB: ssb: use devm_kzalloc
USB: ssb: fix error handling in ssb_hcd_create_pdev()
usb: isp1760: check for null return from kzalloc
cdc-acm: Add support of ATOL FPrint fiscal printers
usb: chipidea: usbmisc_imx: Remove unneeded semicolon
USB: usbtmc: add device quirk for Rigol DS6104
USB: serial: mos7840: Use setup_timer
phy: twl4030-usb: add ABI documentation
phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
phy: twl4030-usb: make runtime pm more reliable.
drivers:usb:fsl: Fix compilation error for fsl ehci drv
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
...
Pull power supply and reset updates from Sebastian Reichel:
- new charger drivers: BQ24257, BQ25890, AXP288, RT9455
- MAX17042 battery: add health & temperature support
- BQ2415x charger: add ACPI support
- misc fixes and cleanups
* tag 'for-4.2' of git://git.infradead.org/battery-2.6: (32 commits)
power_supply: Correct kerneldoc copy paste errors
wm831x_power: Fix off-by-one at free_irq()
power_supply: rt9455_charger: Fix error reported by static analysis tool
power_supply: bq24257: use flags argument of devm_gpiod_get
power_supply: bq25890: use flags argument of devm_gpiod_get
sbs-battery: add option to always register battery
power: Add devm_power_supply_get_by_phandle() helper function
power_supply: max17042: Add OF support for setting thresholds
power_supply: sysfs: Bring back write to writeable properties
power_supply: rt9455_charger: Check if CONFIG_USB_PHY is enabled
power: reset: gpio-restart: increase priority slightly
power_supply: bq25890: make chip_id int
power_supply: Add support for Richtek RT9455 battery charger
Documentation: devicetree: Add Richtek RT9455 bindings
of: Add vendor prefix for Richtek Technology Corporation
power_supply: 88pm860x_charger: Do not call free_irq() twice
power: bq24190_charger: Change first_time flag reset condition
power: axp288_charger: axp288 charger driver
power: max17042_battery: add HEALTH and TEMP_* properties support
power_supply: Add support for TI BQ25890 charger chip
...
This file depends on Kconfig options all of which are a bool, so
we use the appropriate registration function, which avoids us
relying on an implicit inclusion of <module.h> which we are
doing currently.
While this currently works, we really don't want to be including
the module.h header in non-modular code, which we'd be forced
to do, pending some upcoming code relocation from init.h into
module.h. So we fix it now by using the non-modular equivalent.
Cc: Sebastian Reichel <sre@kernel.org>
Acked-By: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
An error handling in wm831x_power_probe() mistakenly frees a failed-to-
request irq as well as other irqs. I added missing decrement of the loop
counter.
Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The result of container_of macro cannot be NULL, so there is no need to
check whether info is NULL.
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify driver accordingly. Furthermore this is one caller less that
stops us making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify driver accordingly. Furthermore this is one caller less that
stops us making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Commit a22b41a31e ("sbs-battery: Probe should try talking to the
device") introduced a step in probing the SBS battery, that tries to
talk to the device before actually registering it, saying:
this driver doesn't actually try talking to the device at probe
time, so if it's incorrectly configured in the device tree or
platform data (or if the battery has been removed from the system),
then probe will succeed and every access will sit there and time
out. The end result is a possibly laggy system that thinks it has a
battery but can never read status, which isn't very useful.
Which is of course reasonable. However, it is also very well possible
for a device to boot up on wall-power and be connected to a battery
later on. This is a scenario that the driver supported before said patch
was applied, and even easily achieved by booting up with the battery
attached and removing it later on. sbs-battery's 'present' sysfs file
can be used to determine if the device is available or not.
So with automated device detection lacking for now, in some cases it is
possible that one wants to register a battery, even if none are attached
at the moment. To facilitate this, add a module parameter that can be
used to configure forced loading module loading time. If set, the battery
will always be registered without checking the sanity of the connection.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds a resource-managed version of the
power_supply_get_by_phandle() function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The commit edd4ab0559 ("power: max17042_battery: add HEALTH and TEMP_*
properties support") added support for setting voltage and temperature
thresholds with platform data. For DeviceTree default of 0 was always
used.
This caused reporting battery health always as over voltage or
over heated.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: edd4ab0559 ("power: max17042_battery: add HEALTH and TEMP_* properties support")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The fix for NULL pointer exception related to calling uevent for not
finished probe caused to set all writeable properties as non-writeable.
This was caused by checking if property is writeable before the initial
increase of power supply usage counter and in the same time using
wrapper over property_is_writeable(). The wrapper returns ENODEV if the
usage counter is still 0.
The call trace looked like:
device probe:
power_supply_register()
use_cnt = 0;
device_add()
create sysfs entries
power_supply_attr_is_visible()
power_supply_property_is_writeable()
if (use_cnt == 0) return -ENODEV;
use_cnt++;
Replace the usage of wrapper with direct call to property_is_writeable()
from driver. This should be safe call during device probe because
implementations of this callback just return 0/1 for different
properties and they do not access any of the driver's internal data.
Fixes: 8e59c7f234 ("power_supply: Fix NULL pointer dereference during bq27x00_battery probe")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If CONFIG_USB_PHY is not enabled, struct notifier_block is not defined and
compilation fails. Therefore, the functions that process USB event
notifications are defined only if CONFIG_USB_PHY is enabled.
There is no need to define these functions if CONFIG_USB_PHY is not
enabled, since no USB notifications are received in this case.
Also, since rt9455_set_boost_voltage_before_boost_mode() function is
called only if USB_EVENT_ID notification is received, this function should
also be defined only if CONFIG_USB_PHY is enabled.
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
gpio-restart uses a priority of 128 and currently most soc-level restart
mechanisms use the same - with some exceptions even using 192.
But while the soc-level restarts are provided by the soc itself,
gpio-restarts will most of the time be board-specfic and be used
when some special board condition makes the soc-level restart
only a second choice.
The problem at hand manifested itself on the rk3288-veyron devices.
While the soc-level restart can sucessfully restart all other rockchip
boards I have, the veyron devices use an external restart mechanism that
seems to not only reset the soc but also some external needed components.
With both restart handlers having priority 128 in my tests the soc-specific
variant took precedent in all cases. While it could restart the soc
sucessfully in all cases, firmware then got an issue when talking to an
external component, resulting in the device being put into recovery mode.
So, give the board-specific restart handler a slight push and move it
to priority 129 to make it more important than the generic soc-specific
restart-handler.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Smatch static checker correctly detected an impossible condition because
chip_id was declared as u8, instead of int:
drivers/power/bq25890_charger.c:843 bq25890_probe()
warn: impossible condition '(bq->chip_id < 0) => (0-255 < 0)'
Also, while at it, fix the return value too.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Felipe writes:
usb: patches for v4.2 merge window
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
My static checker detected double free_irq() in pm860x_charger_remove().
Unloading this module always causes a warning. This patch removes the
first redundant free_irq() call.
Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The initial register reset of BQ24190 generates a charger status change
whose propagation via power_supply_changed is prevented using a flag.
This flag gets never reset so all following events are ignored as well
leading for example to userspace not detecting charger connects/disconnects.
Therefor change the reset condition of first_time flag, so only the
propagation of the first charger status change is prevented.
Signed-off-by: Thomas Elste <thomas.elste@imms.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
twl4030_charger currently finds the associated phy
using usb_get_phy() which will return the first USB2 phy.
If your platform has multiple such phys (as mine does),
this is not reliable (and reliably fails on the GTA04).
Change to use devm_usb_get_phy_by_node(), having found the
node by looking for an appropriately named sibling in
device-tree.
This makes usb-charging dependent on correct device-tree
configuration.
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds new power supply charger driver support
for X-Power AXP288 PMIC integrated charger.
This driver interfaces with the axp20x mfd driver as a cell
and listens to extcon cable events for setting up charging.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
