If the new connection update parameter are accepted, the LE master
host sends the LE Connection Update Command to its controller informing
the new requested parameters.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Use proper timer instead of hci command flow control to timeout
failed hci commands. Otherwise stack ends up sending commands
when flow control is used to block new commands.
2010-09-01 18:29:41.592132 < HCI Command: Remote Name Request (0x01|0x0019) plen 10
bdaddr 00:16:CF:E1:C7:D7 mode 2 clkoffset 0x0000
2010-09-01 18:29:41.592681 > HCI Event: Command Status (0x0f) plen 4
Remote Name Request (0x01|0x0019) status 0x00 ncmd 0
2010-09-01 18:29:51.022033 < HCI Command: Remote Name Request Cancel (0x01|0x001a) plen 6
bdaddr 00:16:CF:E1:C7:D7
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Implements L2CAP Connection Parameter Update Response defined in
the Bluetooth Core Specification, Volume 3, Part A, section 4.21.
Address the LE Connection Parameter Procedure initiated by the slave.
Connection Interval Minimum and Maximum have the same range: 6 to
3200. Time = N * 1.25ms. Minimum shall be less or equal to Maximum.
The Slave Latency field shall have a value in the range of 0 to
((connSupervisionTimeout / connIntervalMax) - 1). Latency field shall
be less than 500. connSupervisionTimeout = Timeout Multiplier * 10 ms.
Multiplier field shall have a value in the range of 10 to 3200.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch splits the L2CAP command handling function in order to
have a clear separation between the commands related to BR/EDR and
LE. Commands and responses in the LE signaling channel are not being
handled yet, command reject is sent to all received requests. Bluetooth
Core Specification, Volume 3, Part A, section 4 defines the signaling
packets formats and allowed commands/responses over the LE signaling
channel.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add basic LE connection support to L2CAP. LE
connection can be created by specifying cid
in struct sockaddr_l2
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth chips may have separate buffers for LE traffic.
This patch add support to use LE buffers provided by the chip.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth V4.0 adds support for Low Energy (LE) connections.
Specification introduces new set of hci commands to control LE
connection. This patch adds logic to create, cancel and disconnect
LE connections.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
l2cap_load() was added to trigger l2cap.ko module loading from the RFCOMM
and BNEP modules. Now that L2CAP module is gone, we don't need it anymore.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Actually doesn't make sense have these modules built separately.
The L2CAP layer is needed by almost all Bluetooth protocols and profiles.
There isn't any real use case without having L2CAP loaded.
SCO is only essential for Audio transfers, but it is so small that we can
have it loaded always in bluetooth.ko without problems.
If you really doesn't want it you can disable SCO in the kernel config.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It causes the move of the declaration of 3 functions to l2cap.h:
l2cap_get_ident(), l2cap_send_cmd(), l2cap_build_conf_req()
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
