Intel fixes for regressions, black screens and hangs, for 3.15.
* tag 'drm-intel-fixes-2014-05-16' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Increase WM memory latency values on SNB
drm/i915: restore backlight precision when converting from ACPI
drm/i915: Use the first mode if there is no preferred mode in the EDID
drm/i915/dp: force eDP lane count to max available lanes on BDW
drm/i915/vlv: reset VLV media force wake request register
drm/i915/SDVO: For sysfs link put directory and target in correct order
drm/i915: use lane count and link rate from VBT as minimums for eDP
drm/i915: clean up VBT eDP link param decoding
drm/i915: consider the source max DP lane count too
On SNB the BIOS provided WM memory latency values seem insufficient to
handle high resolution displays.
In this particular case the display mode was a 2560x1440@60Hz, which
makes the pixel clock 241.5 MHz. It was empirically found that a memory
latency value if 1.2 usec is enough to avoid underruns, whereas the BIOS
provided value of 0.7 usec was clearly too low. Incidentally 1.2 usec
is what the typical BIOS provided values are on IVB systems.
Increase the WM memory latency values to at least 1.2 usec on SNB.
Hopefully this won't have a significant effect on power consumption.
v2: Increase the latency values regardless of the pixel clock
Cc: Robert N <crshman@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70254
Tested-by: Robert Navarro <crshman@gmail.com>
Tested-by: Vitaly Minko <vitaly.minko@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we set backlight on behalf of ACPI opregion, we will convert the
backlight value in the 0-255 range defined in opregion to the actual
hardware level. Commit 22505b82a2 (drm/i915: avoid brightness overflow
when doing scale) is meant to fix the overflow problem when doing the
conversion, but it also caused a problem that the converted hardware
level doesn't quite represent the intended value: say user wants maximum
backlight level(255 in opregion's range), then we will calculate the
actual hardware level to be: level = freq / max * level, where freq is
the hardware's max backlight level(937 on an user's box), and max and
level are all 255. The converted value should be 937 but the above
calculation will yield 765.
To fix this issue, just use 64 bits to do the calculation to keep the
precision and avoid overflow at the same time.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=72491
Reported-by: Nico Schottelius <nico-bugzilla.kernel.org@schottelius.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This matches the algorithm used by earlier kernels when selecting the
mode for the fbcon. And only if there is no modes at all, do we fall
back to using the BIOS configuration. Seamless transition is still
preserved (from the BIOS configuration to ours) so long as the BIOS has
also chosen what we hope is the native configuration.
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78655
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[Jani: applied Chris' "Please imagine that I wrote this correctly."]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There are certain BDW high res eDP machines that regressed due to
commit 38aecea0cc
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Mar 3 11:18:10 2014 +0100
drm/i915: reverse dp link param selection, prefer fast over wide again
The commit lead to 2 lanes at 5.4 Gbps being used instead of 4 lanes at
2.7 Gbps on the affected machines. Link training succeeded for both, but
the screen remained blank with the former config. Further investigation
showed that 4 lanes at 5.4 Gbps worked also.
The root cause for the blank screen using 2 lanes remains unknown, but
apparently the driver for a certain other operating system by default
uses the max available lanes. Follow suit on Broadwell eDP, for at least
until we figure out what is going on.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76711
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When linking the i2c sysfs file into the connector's directory
pass directory and link target in the right order.
This code was introduced with:
commit 931c1c2698
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Feb 11 17:12:51 2014 +0200
drm/i915: sdvo: add i2c sysfs symlink to the connector's directory
This is the same what we do for DP connectors, so make things more
consistent.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Even if the panel claims it can support 4 lanes, there's the
possibility that the HW can't, so consider this while selecting the
max lane count.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
nouveau fixes.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/gm107/gr: bump attrib cb size quite a bit
drm/nouveau: fix another lock unbalance in nouveau_crtc_page_flip
drm/nouveau/bios: fix shadowing from PROM on big-endian systems
drm/nouveau/acpi: allow non-optimus setups to load vbios from acpi
Some more i915 fixes. There's still some DP issues we are looking into,
but wanted to get these moving.
* tag 'topc/core-stuff-2014-05-05' of git://anongit.freedesktop.org/drm-intel:
drm/i915: don't try DP_LINK_BW_5_4 on HSW ULX
drm/i915: Sanitize the enable_ppgtt module option once
drm/i915: Break encoder->crtc link separately in intel_sanitize_crtc()
- Use vddc/sclk dep table for voltage if available
- Fix UVD DPM setup
- Patch voltage tables properly for non-UVD blocks
- Fix DPM + UVD/VCE on Mullins
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
The way the tile mode array index was calculated only makes sense for
the CIK specific macrotile mode array. For SI, we need to use one of the
tile mode array indices reserved for displayable surfaces.
This happened to result in correct display most if not all of the time
because most of the SI tiling modes use the same number of banks.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
When initially looking at traces, missed the fact the binary driver was
using large pages.
Fixes page faults when launching geometry shaders.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
