Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Update vhost-scsi to support F_ANY_LAYOUT using mm/iov_iter.c
logic, and signal VERSION_1 support (MST + Viro + nab)
- Fix iscsi/iser-target to remove problematic active_ts_set usage
(Gavin Guo)
- Update iscsi/iser-target to support multi-sequence sendtargets
(Sagi)
- Fix original PR_APTPL_BUF_LEN 8k size limitation (Martin Svec)
- Add missing WRITE_SAME end-of-device sanity check (Bart)
- Check for LBA + sectors wrap-around in sbc_parse_cdb() (nab)
- Other various minor SPC/SBC compliance fixes based upon Ronnie
Sahlberg test suite (nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (32 commits)
target: Set LBPWS10 bit in Logical Block Provisioning EVPD
target: Fail UNMAP when emulate_tpu=0
target: Fail WRITE_SAME w/ UNMAP=1 when emulate_tpws=0
target: Add sanity checks for DPO/FUA bit usage
target: Perform PROTECT sanity checks for WRITE_SAME
target: Fail I/O with PROTECT bit when protection is unsupported
target: Check for LBA + sectors wrap-around in sbc_parse_cdb
target: Add missing WRITE_SAME end-of-device sanity check
iscsi-target: Avoid IN_LOGOUT failure case for iser-target
target: Fix PR_APTPL_BUF_LEN buffer size limitation
iscsi-target: Drop problematic active_ts_list usage
iscsi/iser-target: Support multi-sequence sendtargets text response
iser-target: Remove duplicate function names
vhost/scsi: potential memory corruption
vhost/scsi: Global tcm_vhost -> vhost_scsi rename
vhost/scsi: Drop left-over scsi_tcq.h include
vhost/scsi: Set VIRTIO_F_ANY_LAYOUT + VIRTIO_F_VERSION_1 feature bits
vhost/scsi: Add ANY_LAYOUT support in vhost_scsi_handle_vq
vhost/scsi: Add ANY_LAYOUT iov -> sgl mapping prerequisites
vhost/scsi: Change vhost_scsi_map_to_sgl to accept iov ptr + len
...
This patch sets the missing LBPWS10 bit within spc_emulate_evpd_b2()
in order to signal WRITE_SAME (10) w/ UNMAP support, following the
existing LBPWS bit to signal WRITE_SAME (16) w/ UNMAP support.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check within sbc_parse_cdb() to fail a UNMAP op,
if the backend device has emulate_tpu disabled.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check within sbc_setup_write_same() to fail a
WRITE_SAME w/ UNMAP=1 op, if the backend device has emulate_tpws
disabled.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a sbc_check_dpofua() function that performs sanity
checks for DPO/FUA command bits.
It introduces checks to fail when either bit is set, but the backend
device is not advertising support for them.
It also moves the existing cmd->se_cmd_flags |= SCF_FUA assignement
into the new helper function.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a call to sbc_check_prot() within sbc_setup_write_same()
code to perform the various protection releated sanity checks, including
failing if WRPROTECT or RDPROTECT is set for a backend device that has
not advertised support for T10-PI.
Also, since WRITE_SAME + T10-PI is currently not supported by IBLOCK +
FILEIO backends, go ahead and fail if ->execute_write_same() is invoked
with a non zero cmd->prot_op.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an explicit check for WRPROTECT + RDPROTECT bit usage
within sbc_check_prot(), and fails with TCM_INVALID_CDB_FIELD if the
backend device does not have protection enabled.
Also, update sbc_check_prot() to return sense_reason_t in order to
propigate up the correct sense ASQ.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check to sbc_parse_cdb() in order to detect when
an LBA + sector vs. end-of-device calculation wraps when the LBA is
sufficently large enough (eg: 0xFFFFFFFFFFFFFFFF).
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check to sbc_setup_write_same() to verify
the incoming WRITE_SAME LBA + number of blocks does not exceed
past the end-of-device.
Also check for potential LBA wrap-around as well.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses the original PR_APTPL_BUF_LEN = 8k limitiation
for write-out of PR APTPL metadata that Martin has recently been
running into.
It changes core_scsi3_update_and_write_aptpl() to use vzalloc'ed
memory instead of kzalloc, and increases the default hardcoded
length to 256k.
It also adds logic in core_scsi3_update_and_write_aptpl() to double
the original length upon core_scsi3_update_aptpl_buf() failure, and
retries until the vzalloc'ed buffer is large enough to accommodate
the outgoing APTPL metadata.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case sendtargets response is larger than initiator MRDSL, we
send a partial sendtargets response (setting F=0, C=1, TTT!=0xffffffff),
accept a consecutive empty text message and send the rest of the payload.
In case we are done, we set F=1, C=0, TTT=0xffffffff.
We do that by storing the sendtargets response bytes done under
the session.
This patch also makes iscsit_find_cmd_from_itt public for isert.
(Re-add cmd->maxcmdsn_inc and clear in iscsit_build_text_rsp - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
No reason to allocate a buffer of size bigger than initiator
MaxRecvDataSegmentLength. Moreover, we need to respect initiator
MRDSL and not send a larger payload.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Seems strange to see in include/target/iscsi/iscsi_transport.h:
include "../../../drivers/target/iscsi/iscsi_target_core.h"
Move it to it's natural location.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of pushing each byte via stack the %*ph specifier allows to supply just
a pointer and length of the buffer. The patch converts code to use the
specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Everything else starts with ICF so the last two should as well.
Fix places they are used to match.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For PGR reservation of type Write Exclusive Access, allow all non
reservation holding I_T nexuses with active registrations to READ
from the device.
This addresses a bug where active registrations that attempted
to READ would result in an reservation conflict.
Signed-off-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that fabric_max_sectors is no longer used to enforce the maximum
I/O size, go ahead and drop it's left-over usage in target-core and
associated backend drivers.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops the arbitrary maximum I/O size limit in sbc_parse_cdb(),
which currently for fabric_max_sectors is hardcoded to 8192 (4 MB for 512
byte sector devices), and for hw_max_sectors is a backend driver dependent
value.
This limit is problematic because Linux initiators have only recently
started to honor block limits MAXIMUM TRANSFER LENGTH, and other non-Linux
based initiators (eg: MSFT Fibre Channel) can also generate I/Os larger
than 4 MB in size.
Currently when this happens, the following message will appear on the
target resulting in I/Os being returned with non recoverable status:
SCSI OP 28h with too big sectors 16384 exceeds fabric_max_sectors: 8192
Instead, drop both [fabric,hw]_max_sector checks in sbc_parse_cdb(),
and convert the existing hw_max_sectors into a purely informational
attribute used to represent the granuality that backend driver and/or
subsystem code is splitting I/Os upon.
Also, update FILEIO with an explicit FD_MAX_BYTES check in fd_execute_rw()
to deal with the one special iovec limitiation case.
v2 changes:
- Drop hw_max_sectors check in sbc_parse_cdb()
Reported-by: Lance Gropper <lance.gropper@qosserver.com>
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org # 3.4
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI update from James Bottomley:
"This is a much shorter set of patches that were on the go but didn't
make it in to the early pull request for the merge window. It's
really a set of bug fixes plus some final cleanup work on the new tag
queue API"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
storvsc: ring buffer failures may result in I/O freeze
ipr: set scsi_level correctly for disk arrays
ipr: add support for async scanning to speed up boot
scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
scsi_debug: take sdebug_host_list_lock when changing capacity
scsi_debug: improve driver description in Kconfig
scsi_debug: fix compare and write errors
qla2xxx: fix race in handling rport deletion during recovery causes panic
scsi: blacklist RSOC for Microsoft iSCSI target devices
scsi: fix random memory corruption with scsi-mq + T10 PI
Revert "[SCSI] mpt3sas: Remove phys on topology change"
Revert "[SCSI] mpt2sas: Remove phys on topology change."
esas2r: Correct typos of "validate" in a comment
fc: FCP_PTA_SIMPLE is 0
ibmvfc: remove unused tag variable
scsi: remove MSG_*_TAG defines
scsi: remove scsi_set_tag_type
scsi: remove scsi_get_tag_type
scsi: never drop to untagged mode during queue ramp down
scsi: remove ->change_queue_type method
Pull SCSI target fixes from Nicholas Bellinger:
"The highlights this merge window include:
- Allow target fabric drivers to function as built-in. (Roland)
- Fix tcm_loop multi-TPG endpoint nexus bug. (Hannes)
- Move per device config_item_type into se_subsystem_api, allowing
configfs attributes to be defined at module_init time. (Jerome +
nab)
- Convert existing IBLOCK/FILEIO/RAMDISK/PSCSI/TCMU drivers to use
external configfs attributes. (nab)
- A number of iser-target fixes related to active session + network
portal shutdown stability during extended stress testing. (Sagi +
Slava)
- Dynamic allocation of T10-PI contexts for iser-target, fixing a
potentially bogus iscsi_np->tpg_np pointer reference in >= v3.14
code. (Sagi)
- iser-target performance + scalability improvements. (Sagi)
- Fixes for SPC-4 Persistent Reservation AllRegistrants spec
compliance. (Ilias + James + nab)
- Avoid potential short kern_sendmsg() in iscsi-target for now until
Al's conversion to use msghdr iteration is merged post -rc1.
(Viro)
Also, Sagi has requested a number of iser-target patches (9) that
address stability issues he's encountered during extended stress
testing be considered for v3.10.y + v3.14.y code. Given the amount of
LOC involved, it will certainly require extra backporting effort.
Apologies in advance to Greg-KH & Co on this. Sagi and I will be
working post-merge to ensure they each get applied correctly"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (53 commits)
target: Allow AllRegistrants to re-RESERVE existing reservation
uapi/linux/target_core_user.h: fix headers_install.sh badness
iscsi-target: Fail connection on short sendmsg writes
iscsi-target: nullify session in failed login sequence
target: Avoid dropping AllRegistrants reservation during unregister
target: Fix R_HOLDER bit usage for AllRegistrants
iscsi-target: Drop left-over bogus iscsi_np->tpg_np
iser-target: Fix wc->wr_id cast warning
iser-target: Remove code duplication
iser-target: Adjust log levels and prettify some prints
iser-target: Use debug_level parameter to control logging level
iser-target: Fix logout sequence
iser-target: Don't wait for session commands from completion context
iser-target: Reduce CQ lock contention by batch polling
iser-target: Introduce isert_poll_budget
iser-target: Remove an atomic operation from the IO path
iser-target: Remove redundant call to isert_conn_terminate
iser-target: Use single CQ for TX and RX
iser-target: Centralize completion elements to a context
iser-target: Cast wr_id with uintptr_t instead of unsinged long
...
This patch changes core_scsi3_pro_release() logic to allow an
existing AllRegistrants type reservation to be re-reserved by
any registered I_T nexus.
This addresses a issue where AllRegistrants type RESERVE was
receiving RESERVATION_CONFLICT status if dev_pr_res_holder did
not match the same I_T nexus, instead of just returning GOOD
status following spc4r34 Section 5.9.9:
"If the device server receives a PERSISTENT RESERVE OUT command
with RESERVE service action where the TYPE field and the SCOPE
field contain the same values as the existing type and scope
from a persistent reservation holder, it shall not make any
change to the existing persistent reservation and shall complete
the command with GOOD status."
Reported-by: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
