We always use resched_task() with rq->curr argument.
It's not possible to reschedule any task but rq's current.
The patch introduces resched_curr(struct rq *) to
replace all of the repeating patterns. The main aim
is cleanup, but there is a little size profit too:
(before)
$ size kernel/sched/built-in.o
text data bss dec hex filename
155274 16445 7042 178761 2ba49 kernel/sched/built-in.o
$ size vmlinux
text data bss dec hex filename
7411490 1178376 991232 9581098 92322a vmlinux
(after)
$ size kernel/sched/built-in.o
text data bss dec hex filename
155130 16445 7042 178617 2b9b9 kernel/sched/built-in.o
$ size vmlinux
text data bss dec hex filename
7411362 1178376 991232 9580970 9231aa vmlinux
I was choosing between resched_curr() and resched_rq(),
and the first name looks better for me.
A little lie in Documentation/trace/ftrace.txt. I have not
actually collected the tracing again. With a hope the patch
won't make execution times much worse :)
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20140628200219.1778.18735.stgit@localhost
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 4fc828e24c ("locking/rwsem: Support optimistic spinning")
introduced a major performance regression for workloads such as
xfs_repair which mix read and write locking of the mmap_sem across
many threads. The result was xfs_repair ran 5x slower on 3.16-rc2
than on 3.15 and using 20x more system CPU time.
Perf profiles indicate in some workloads that significant time can
be spent spinning on !owner. This is because we don't set the lock
owner when readers(s) obtain the rwsem.
In this patch, we'll modify rwsem_can_spin_on_owner() such that we'll
return false if there is no lock owner. The rationale is that if we
just entered the slowpath, yet there is no lock owner, then there is
a possibility that a reader has the lock. To be conservative, we'll
avoid spinning in these situations.
This patch reduced the total run time of the xfs_repair workload from
about 4 minutes 24 seconds down to approximately 1 minute 26 seconds,
back to close to the same performance as on 3.15.
Retesting of AIM7, which were some of the workloads used to test the
original optimistic spinning code, confirmed that we still get big
performance gains with optimistic spinning, even with this additional
regression fix. Davidlohr found that while the 'custom' workload took
a performance hit of ~-14% to throughput for >300 users with this
additional patch, the overall gain with optimistic spinning is
still ~+45%. The 'disk' workload even improved by ~+15% at >1000 users.
Tested-by: Dave Chinner <dchinner@redhat.com>
Acked-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Jason Low <jason.low2@hp.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1404532172.2572.30.camel@j-VirtualBox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ring_buffer_poll_wait() should always put the poll_table to its wait_queue
even there is immediate data available. Otherwise, the following epoll and
read sequence will eventually hang forever:
1. Put some data to make the trace_pipe ring_buffer read ready first
2. epoll_ctl(efd, EPOLL_CTL_ADD, trace_pipe_fd, ee)
3. epoll_wait()
4. read(trace_pipe_fd) till EAGAIN
5. Add some more data to the trace_pipe ring_buffer
6. epoll_wait() -> this epoll_wait() will block forever
~ During the epoll_ctl(efd, EPOLL_CTL_ADD,...) call in step 2,
ring_buffer_poll_wait() returns immediately without adding poll_table,
which has poll_table->_qproc pointing to ep_poll_callback(), to its
wait_queue.
~ During the epoll_wait() call in step 3 and step 6,
ring_buffer_poll_wait() cannot add ep_poll_callback() to its wait_queue
because the poll_table->_qproc is NULL and it is how epoll works.
~ When there is new data available in step 6, ring_buffer does not know
it has to call ep_poll_callback() because it is not in its wait queue.
Hence, block forever.
Other poll implementation seems to call poll_wait() unconditionally as the very
first thing to do. For example, tcp_poll() in tcp.c.
Link: http://lkml.kernel.org/p/20140610060637.GA14045@devbig242.prn2.facebook.com
Cc: stable@vger.kernel.org # 2.6.27
Fixes: 2a2cc8f7c4 "ftrace: allow the event pipe to be polled"
Reviewed-by: Chris Mason <clm@fb.com>
Signed-off-by: Martin Lau <kafai@fb.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When the create_worker() is called from non-manager, the struct worker
is allocated from the node of the caller which may be different from the
node of pool->node.
So we add a node ID argument for the alloc_worker() to ensure the
struct worker is allocated from the preferable node.
tj: @nid renamed to @node for consistency.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Running my ftrace tests on PowerPC, it failed the test that checks
if function_graph tracer is affected by the stack tracer. It was.
Looking into this, I found that the update_function_graph_func()
must be called even if the trampoline function is not changed.
This is because archs like PowerPC do not support ftrace_ops being
passed by assembly and instead uses a helper function (what the
trampoline function points to). Since this function is not changed
even when multiple ftrace_ops are added to the code, the test that
falls out before calling update_function_graph_func() will miss that
the update must still be done.
Call update_function_graph_function() for all calls to
update_ftrace_function()
Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
cgrp_dfl_root_inhibit_ss_mask determines which subsystems are not
supported on the default hierarchy and is currently initialized
statically and just includes the debug subsystem. Now that there's
cgroup_subsys->dfl_files, we can easily tell which subsystems support
the default hierarchy or not.
Let's initialize cgrp_dfl_root_inhibit_ss_mask by testing whether
cgroup_subsys->dfl_files is NULL. After all, subsystems with NULL
->dfl_files aren't useable on the default hierarchy anyway.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
cgroup now distinguishes cftypes for the default and legacy
hierarchies more explicitly by using separate arrays and
CFTYPE_ONLY_ON_DFL and CFTYPE_INSANE should be and are used only
inside cgroup core proper. Let's make it clear that the flags are
internal by prefixing them with double underscores.
CFTYPE_INSANE is renamed to __CFTYPE_NOT_ON_DFL for consistency. The
two flags are also collected and assigned bits >= 16 so that they
aren't mixed with the published flags.
v2: Convert the extra ones in cgroup_exit_cftypes() which are added by
revision to the previous patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Until now, cftype arrays carried files for both the default and legacy
hierarchies and the files which needed to be used on only one of them
were flagged with either CFTYPE_ONLY_ON_DFL or CFTYPE_INSANE. This
gets confusing very quickly and we may end up exposing interface files
to the default hierarchy without thinking it through.
This patch makes cgroup core provide separate sets of interfaces for
cftype handling so that the cftypes for the default and legacy
hierarchies are clearly distinguished. The previous two patches
renamed the existing ones so that they clearly indicate that they're
for the legacy hierarchies. This patch adds the interface for the
default hierarchy and apply them selectively depending on the
hierarchy type.
* cftypes added through cgroup_subsys->dfl_cftypes and
cgroup_add_dfl_cftypes() only show up on the default hierarchy.
* cftypes added through cgroup_subsys->legacy_cftypes and
cgroup_add_legacy_cftypes() only show up on the legacy hierarchies.
* cgroup_subsys->dfl_cftypes and ->legacy_cftypes can point to the
same array for the cases where the interface files are identical on
both types of hierarchies.
* This makes all the existing subsystem interface files legacy-only by
default and all subsystems will have no interface file created when
enabled on the default hierarchy. Each subsystem should explicitly
review and compose the interface for the default hierarchy.
* A boot param "cgroup__DEVEL__legacy_files_on_dfl" is added which
makes subsystems which haven't decided the interface files for the
default hierarchy to present the legacy files on the default
hierarchy so that its behavior on the default hierarchy can be
tested. As the awkward name suggests, this is for development only.
* memcg's CFTYPE_INSANE on "use_hierarchy" is noop now as the whole
array isn't used on the default hierarchy. The flag is removed.
v2: Updated documentation for cgroup__DEVEL__legacy_files_on_dfl.
v3: Clear CFTYPE_ONLY_ON_DFL and CFTYPE_INSANE when cfts are removed
as suggested by Li.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Currently, cftypes added by cgroup_add_cftypes() are used for both the
unified default hierarchy and legacy ones and subsystems can mark each
file with either CFTYPE_ONLY_ON_DFL or CFTYPE_INSANE if it has to
appear only on one of them. This is quite hairy and error-prone.
Also, we may end up exposing interface files to the default hierarchy
without thinking it through.
cgroup_subsys will grow two separate cftype addition functions and
apply each only on the hierarchies of the matching type. This will
allow organizing cftypes in a lot clearer way and encourage subsystems
to scrutinize the interface which is being exposed in the new default
hierarchy.
In preparation, this patch adds cgroup_add_legacy_cftypes() which
currently is a simple wrapper around cgroup_add_cftypes() and replaces
all cgroup_add_cftypes() usages with it.
While at it, this patch drops a completely spurious return from
__hugetlb_cgroup_file_init().
This patch doesn't introduce any functional differences.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Currently, cgroup_subsys->base_cftypes is used for both the unified
default hierarchy and legacy ones and subsystems can mark each file
with either CFTYPE_ONLY_ON_DFL or CFTYPE_INSANE if it has to appear
only on one of them. This is quite hairy and error-prone. Also, we
may end up exposing interface files to the default hierarchy without
thinking it through.
cgroup_subsys will grow two separate cftype arrays and apply each only
on the hierarchies of the matching type. This will allow organizing
cftypes in a lot clearer way and encourage subsystems to scrutinize
the interface which is being exposed in the new default hierarchy.
In preparation, this patch renames cgroup_subsys->base_cftypes to
cgroup_subsys->legacy_cftypes. This patch is pure rename.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Currently cgroup_base_files[] contains the cgroup core interface files
for both legacy and default hierarchies with each file tagged with
CFTYPE_INSANE and CFTYPE_ONLY_ON_DFL. This is difficult to read.
Let's separate it out to two separate tables, cgroup_dfl_base_files[]
and cgroup_legacy_base_files[], and use the appropriate one in
cgroup_mkdir() depending on the hierarchy type. This makes tagging
each file unnecessary.
This patch doesn't introduce any behavior changes.
v2: cgroup_dfl_base_files[] was missing the termination entry
triggering WARN in cgroup_init_cftypes() for 0day kernel testing
robot. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Jet Chen <jet.chen@intel.com>
Currently trace option stacktrace is not applicable for
trace_printk with constant string argument, the reason is
in __trace_puts/__trace_bputs ftrace_trace_stack is missing.
In contrast, when using trace_printk with non constant string
argument(will call into __trace_printk/__trace_bprintk), then
trace option stacktrace is workable, this inconstant result
will confuses users a lot.
Link: http://lkml.kernel.org/p/51E7A7C9.9040401@huawei.com
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The commit [247bc037: PM / Sleep: Mitigate race between the freezer
and request_firmware()] introduced the finer state control, but it
also leads to a new bug; for example, a bug report regarding the
firmware loading of intel BT device at suspend/resume:
https://bugzilla.novell.com/show_bug.cgi?id=873790
The root cause seems to be a small window between the process resume
and the clear of usermodehelper lock. The request_firmware() function
checks the UMH lock and gives up when it's in UMH_DISABLE state. This
is for avoiding the invalid f/w loading during suspend/resume phase.
The problem is, however, that usermodehelper_enable() is called at the
end of thaw_processes(). Thus, a thawed process in between can kick
off the f/w loader code path (in this case, via btusb_setup_intel())
even before the call of usermodehelper_enable(). Then
usermodehelper_read_trylock() returns an error and request_firmware()
spews WARN_ON() in the end.
This oneliner patch fixes the issue just by setting to UMH_FREEZING
state again before restarting tasks, so that the call of
request_firmware() will be blocked until the end of this function
instead of returning an error.
Fixes: 247bc03742 (PM / Sleep: Mitigate race between the freezer and request_firmware())
Link: https://bugzilla.novell.com/show_bug.cgi?id=873790
Cc: 3.4+ <stable@vger.kernel.org> # 3.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
