Rename v4l2_format_sdr to v4l2_sdr_format in order to keep it in
line with other formats.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add volatile boolean control to indicate if tuner frequency synthesizer
is locked to requested frequency. That means tuner is able to receive
given frequency. Control is named as "PLL lock", since frequency
synthesizers are based of phase-locked-loop. Maybe more general name
could be wise still?
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It appears that controls are ordered by ID number when enumerating.
That could lead illogical UI as controls are usually enumerated and
drawn by the application at runtime.
Change order of controls by reorganizing assigned IDs now as we can.
It is not reasonable possible after the API is released. Also, leave
some spare space between IDs too for possible future extensions.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modern silicon RF tuners has one or more adjustable filters on
signal path, in order to filter noise from desired radio channel.
Add channel bandwidth control to tell the driver which is radio
channel width we want receive. Filters could be then adjusted by
the driver or hardware, using RF frequency and channel bandwidth
as a base of filter calculations.
On automatic mode (normal mode), bandwidth is calculated from sampling
rate or tuning info got from userspace. That new control gives
possibility to set manual mode and let user have more control for
filters.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both QEMU and KVM have already accumulated a significant number of
optimizations based on the hard-coded assumption that ioapic polarity
will always use the ActiveHigh convention, where the logical and
physical states of level-triggered irq lines always match (i.e.,
active(asserted) == high == 1, inactive == low == 0). QEMU guests
are expected to follow directions given via ACPI and configure the
ioapic with polarity 0 (ActiveHigh). However, even when misbehaving
guests (e.g. OS X <= 10.9) set the ioapic polarity to 1 (ActiveLow),
QEMU will still use the ActiveHigh signaling convention when
interfacing with KVM.
This patch modifies KVM to completely ignore ioapic polarity as set by
the guest OS, enabling misbehaving guests to work alongside those which
comply with the ActiveHigh polarity specified by QEMU's ACPI tables.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gabriel L. Somlo <somlo@cmu.edu>
[Move documentation to KVM_IRQ_LINE, add ia64. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce new FALLOC_FL_ZERO_RANGE flag for fallocate. This has the same
functionality as xfs ioctl XFS_IOC_ZERO_RANGE.
It can be used to convert a range of file to zeros preferably without
issuing data IO. Blocks should be preallocated for the regions that span
holes in the file, and the entire range is preferable converted to
unwritten extents - even though file system may choose to zero out the
extent or do whatever which will result in reading zeros from the range
while the range remains allocated for the file.
This can be also used to preallocate blocks past EOF in the same way as
with fallocate. Flag FALLOC_FL_KEEP_SIZE which should cause the inode
size to remain the same.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Struct v4l2_subdev_edid and the VIDIOC_SUBDEV_G/S_EDID ioctls were
specific for subdevices, but for hardware with a simple video pipeline
you do not need/want to create subdevice nodes to just get/set the EDID.
Move the v4l2_subdev_edid struct to v4l2-common.h and rename as
v4l2_edid. Add the same ioctls to videodev2.h as well, thus allowing
this API to be used with both video nodes and v4l-subdev nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Three Flash fault are added. V4L2_FLASH_FAULT_UNDER_VOLTAGE for the case low
voltage below the min. limit. V4L2_FLASH_FAULT_INPUT_VOLTAGE for the case
falling input voltage and chip adjust flash current not occur under voltage
event. V4L2_FLASH_FAULT_LED_OVER_TEMPERATURE for the case the temperature
exceed the maximun limit
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Felipe writes:
usb: patches for v3.15
another substantial pull request with new features all over
the place.
dwc3 got a bit closer towards hibernation support with after
a few patches re-factoring code to be reused for hibernation.
Also in dwc3 two new workarounds for known silicon bugs have
been implemented, some randconfig build errors have been fixed,
and it was taught about the new generic phy layer.
MUSB on AM335x now supports isochronous transfers thanks to
George Cherian's work.
The atmel_usba driver got two crash fixes: one when no endpoint
was specified in DeviceTree data and another when stopping the UDC
in DEBUG builds.
Function FS got a much needed fix to ffs_epfile_io() which was
copying too much data to userspace in some cases.
The printer gadget got a fix for a possible deadlock and plugged
a memory leak.
Ethernet drivers now use NAPI for RX which gives improved throughput.
Other than that, the usual miscelaneous fixes, cleanups, and
the like.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Linux 3.13
Conflicts:
include/net/xfrm.h
Simple merge where v3.13 removed 'extern' from definitions and the audit
tree did s/u32/unsigned int/ to the same definitions.
The configuration for CAN FD depends on CAN_CTRLMODE_FD enabled in the driver
specific ctrlmode_supported capabilities.
The configuration can be done either with the 'fd { on | off }' option in the
'ip' tool from iproute2 or by setting the CAN netdevice MTU to CAN_MTU (16) or
to CANFD_MTU (72).
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As CAN FD offers a second bitrate for the data section of the CAN frame the
infrastructure for storing and configuring this second bitrate is introduced.
Improved the readability of the if-statement by inserting some newlines.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to allow a future ioctl parameter, such as a creation flag,
we change the UBI_IOCVOLCRBLK so it accepts a struct ubi_blkcreate_req.
For the time being the structure is not in use, but fully reserved.
This ABI change is still possible and harmless, because the ioctl has just
been introduced and there's no userspace program which uses it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Adds a new property for hash set types, where if a set is created
with the 'forceadd' option and the set becomes full the next addition
to the set may succeed and evict a random entry from the set.
To keep overhead low eviction is done very simply. It checks to see
which bucket the new entry would be added. If the bucket's pos value
is non-zero (meaning there's at least one entry in the bucket) it
replaces the first entry in the bucket. If pos is zero, then it continues
down the normal add process.
This property is useful if you have a set for 'ban' lists where it may
not matter if you release some entries from the set early.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
commit 2dfb973c0dcc6d2211 (add markmask for hash:ip,mark data type)
inserted IPSET_ATTR_MARKMASK in-between other enum values, i.e.
changing values of all further attributes. This causes 'ipset list'
segfault on existing kernels since ipset no longer finds
IPSET_ATTR_MEMSIZE (it has a different value on kernel side).
Jozsef points out it should be moved below IPSET_ATTR_MARK which
works since there is some extra reserved space after that value.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Introduce packet mark mask for hash:ip,mark data type. This allows to
set mark bit filter for the ip set.
Change-Id: Id8dd9ca7e64477c4f7b022a1d9c1a5b187f1c96e
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Introduce packet mark support with new ip,mark hash set. This includes
userspace and kernelspace code, hash:ip,mark set tests and man page
updates.
The intended use of ip,mark set is similar to the ip:port type, but for
protocols which don't use a predictable port number. Instead of port
number it matches a firewall mark determined by a layer 7 filtering
program like opendpi.
As well as allowing or blocking traffic it will also be used for
accounting packets and bytes sent for each protocol.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
