The USB PHY member of the HCD structure is renamed to 'usb_phy' and
modifications are done in all drivers accessing it.
This is in preparation to adding the generic PHY support.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
[Sergei: added missing 'drivers/usb/misc/lvstest.c' file, resolved rejects,
updated changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.
All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have only needed to enable otg initialization when both of
below conditions are satisfied:
- The controller is otg capable
- The gadget function is enabled
If the controller is otg capable, but is host-only configuration, we do
not need to access register otgsc and do any otg operations (eg, create
otg workqueue).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For OTG and Embedded hosts, they may need TPL (Targeted Peripheral List)
for usb certification and other vender specific requirements, the
platform can tell chipidea core driver if it supports tpl through DT
or platform data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB updates from Greg KH:
"Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while"
* tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (211 commits)
USB: devio: fix issue with log flooding
uas: Log a warning when we cannot use uas because the hcd lacks streams
uas: Only complain about missing sg if all other checks succeed
xhci: Add missing checks for xhci_alloc_command failure
xhci: Rename Asrock P67 pci product-id to EJ168
xhci: Blacklist using streams on the Etron EJ168 controller
uas: Limit qdepth to 32 when connected over usb-2
uwb/whci: use correct structure type name in sizeof
usb-core bInterval quirk
USB: serial: ftdi_sio: Add support for new Xsens devices
USB: serial: ftdi_sio: Annotate the current Xsens PID assignments
usb: chipidea: debug: fix sparse non static symbol warnings
usb: ci_hdrc_imx doc: fsl,usbphy is required
usb: ci_hdrc_imx: Return -EINVAL for missing USB PHY
usb: core: allow zero packet flag for interrupt urbs
usb: lvstest: Fix sparse warnings generated by kbuild test bot
USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down
phy: miphy365x: Represent each PHY channel as a DT subnode
phy: miphy365x: Provide support for the MiPHY356x Generic PHY
phy: miphy365x: Add Device Tree bindings for the MiPHY365x
...
Fixes the following sparse warnings:
drivers/usb/chipidea/debug.c:211:5: warning:
symbol 'ci_otg_show' was not declared. Should it be static?
drivers/usb/chipidea/debug.c:334:5: warning:
symbol 'ci_registers_show' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-ENODEV is interpreted by the generic driver probing function as a
non-matching driver. This leads to a missing probe failure message.
Also a missing USB PHY is more of an invalid configuration of the usb
driver because it is necessary.
This patch returns -EINVAL if devm_usb_get_phy_by_phandle() returned -ENODEV.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 2 methods for ZLP (zero-length packet) generation:
1) In software
2) Automatic generation by device controller
1) is implemented in UDC driver and it attaches ZLP to IN packet if
descriptor->size < wLength
2) can be enabled/disabled by setting ZLT bit in the QH
When gadget ffs is connected to ubuntu host, the host sends
get descriptor request and wLength in setup packet is 255 while the
size of descriptor which will be sent by gadget in IN packet is
64 byte. So the composite driver sets req->zero = 1.
In UDC driver following code will be executed then
if (hwreq->req.zero && hwreq->req.length
&& (hwreq->req.length % hwep->ep.maxpacket == 0))
add_td_to_list(hwep, hwreq, 0);
Case-A:
So in case of ubuntu host, UDC driver will attach a ZLP to the IN packet.
ubuntu host will request 255 byte in IN request, gadget will send 64 byte
with ZLP and host will come to know that there is no more data.
But hold on, by default ZLT=0 for endpoint 0 so hardware also tries to
automatically generate the ZLP which blocks enumeration for ~6 seconds due
to endpoint 0 STALL, NAKs are sent to host for any requests (OUT/PING)
Case-B:
In case when gadget ffs is connected to Apple device, Apple device sends
setup packet with wLength=64. So descriptor->size = 64 and wLength=64
therefore req->zero = 0 and UDC driver will not attach any ZLP to the
IN packet. Apple device requests 64 bytes, gets 64 bytes and doesn't
further request for IN data. But ZLT=0 by default for endpoint 0 so
hardware tries to automatically generate the ZLP which blocks enumeration
for ~6 seconds due to endpoint 0 STALL, NAKs are sent to host for any
requests (OUT/PING)
According to USB2.0 specs:
8.5.3.2 Variable-length Data Stage
A control pipe may have a variable-length data phase in which the
host requests more data than is contained in the specified data
structure. When all of the data structure is returned to the host,
the function should indicate that the Data stage is ended by
returning a packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of wMaxPacketSize
for the pipe, the function will return a zero-length packet to indicate
the end of the Data stage.
In Case-A mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint 0 OR if software
ZLP generation is not disabled but we set ZLT=1 for endpoint 0 then
enumeration doesn't block for 6 seconds.
In Case-B mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint then enumeration
still blocks due to ZLP automatically generated by hardware and host not needing
it. But if we keep software ZLP generation enabled but we set ZLT=1 for
endpoint 0 then enumeration doesn't block for 6 seconds.
So the proper solution for this issue seems to disable automatic ZLP generation
by hardware (i.e by setting ZLT=1 for endpoint 0) and let software (UDC driver)
handle the ZLP generation based on req->zero field.
Cc: stable@vger.kernel.org
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to delete un-finished td from current request's td list
at ep_dequeue API, otherwise, this non-user td will be remained
at td list before this request is freed. So if we do ep_queue->
ep_dequeue->ep_queue sequence, when the complete interrupt for
the second ep_queue comes, we search td list for this request,
the first td (added by the first ep_queue) will be handled, and
its status is still active, so we will consider the this transfer
still not be completed, but in fact, it has completed. It causes
the peripheral side considers it never receives current data for
this transfer.
We met this problem when do "Error Recovery Test - Device Configured"
test item for USBCV2 MSC test, the host has never received ACK for
the IN token for CSW due to peripheral considers it does not get this
CBW, the USBCV test log like belows:
--------------------------------------------------------------------------
INFO
Issuing BOT MSC Reset, reset should always succeed
INFO
Retrieving status on CBW endpoint
INFO
CBW endpoint status = 0x0
INFO
Retrieving status on CSW endpoint
INFO
CSW endpoint status = 0x0
INFO
Issuing required command (Test Unit Ready) to verify device has recovered
INFO
Issuing CBW (attempt #1):
INFO
|----- CBW LUN = 0x0
INFO
|----- CBW Flags = 0x0
INFO
|----- CBW Data Transfer Length = 0x0
INFO
|----- CBW CDB Length = 0x6
INFO
|----- CBW CDB-00 = 0x0
INFO
|----- CBW CDB-01 = 0x0
INFO
|----- CBW CDB-02 = 0x0
INFO
|----- CBW CDB-03 = 0x0
INFO
|----- CBW CDB-04 = 0x0
INFO
|----- CBW CDB-05 = 0x0
INFO
Issuing CSW : try 1
INFO
CSW Bulk Request timed out!
ERROR
Failed CSW phase : should have been success or stall
FAIL
(5.3.4) The CSW status value must be 0x00, 0x01, or 0x02.
ERROR
BOTCommonMSCRequest failed: error=80004000
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 62bb84e (usb: gadget: ci13xxx: convert to platform device)
start address of the capability registers is not passed correctly to
udc_probe(). Fix this.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The field PLLDIVVALUE of register PHY_CTRL_1 selects the reference clock source
for the PHY:
00 = sysclock uses 19.2 MHz
01 = sysclock uses 24 MHz
10 = sysclock uses 26 MHz
11 = sysclock uses 27 MHz
The reset value for this field is 10 according to the reference manual, and
even though this reset value works for mx53, it does not work for mx51.
So instead of relying on the reset value for the PLLDIVVALUE field, explicitly
set it to 01 so that a 24MHz clock can be selected for the PHY and allowing both
mx51 and mx53 to have USB OTG port functional.
Succesfully tested 'g_ether' on a imx51-babbage and on a imx53-qsb boards.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The otg queue work include operations: one is disable interrupt,
another one is call kernel queue work API. Many codes do this
operation, using one inline function to instead of them.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds sys input to control and show OTG fsm inputs by application,
user can do host and preipheral role switch by change these inputs.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds OTG fsm timers initialization, which use controller's 1ms
interrupt as timeout counter, also adds some local timers which are not
in otg_fsm_timer list.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
