Atmel 840B digitizer presents a stylus interface which reports twice
the X coordinate and then twice the Y coordinate. In its current
implementation, hid-input assign the first X to X, then the second to Y,
then the first Y to Z, then the second one to RX.
This is wrong, and X should always be mapped to X, no matter what.
A solution consists in forcing X, Y, Z, RX, RY, RZ to be mapped to their
correct user space counter part.
Reported-by: Éric Brunet <Eric.Brunet@lps.ens.fr>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On Feb 17, 2014, two new usages are approved to HID usage Table 18 -
Digitizer Page:
5A Secondary Barrel Switch MC 16.4
5B Transducer Serial Number SV 16.3.1
This patch adds relevant definitions to hid/input. It also removes
outdated comments in hid.h.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
SET_REPORT and GET_REPORT are mandatory in the HID specification.
Make the corresponding API in hid-core mandatory too, which removes the
need to test against it in some various places.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_output_raw_report() is not a ll_driver callback and should not be used.
To keep the same code path than before, we are forced to play with the
different hid_hw_* calls: if the usb or i2c device does not support
direct output reports, then we will rely on the SET_REPORT HID call.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a helper to access hdev->hid_output_raw_report().
To convert the drivers, use the following snippets:
for i in drivers/hid/*.c
do
sed -i.bak "s/[^ \t]*->hid_output_raw_report(/hid_output_raw_report(/g" $i
done
Then manually fix for checkpatch.pl
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
dev->hid_get_raw_report(X) and hid_hw_raw_request(X, HID_REQ_GET_REPORT)
are strictly equivalent. Switch the hid subsystem to the hid_hw notation
and remove the field .hid_get_raw_report in struct hid_device.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All the different transport drivers use now the generic event handling
in hid-input. We can remove the handler definitively now.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add mapping for "AL Next Task/Application", "AL Previous Task/Application"
and "AL File Browser" buttons, as found on the Microsoft Office keyboard.
Note that there already is a mapping for "AL Local Machine Browser" to
KEY_FILE. Unless we ever encounter a device with both that should not be
a problem.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When using hid_output_report(), the buffer should be allocated by hid_alloc_report_buf(),
not a custom malloc.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
we used to set the parent of the input device as the parent of
the hid bus. This was introduced when we created hid as a real bus, and
to keep backward compatibility. Now, it's time to proper set the parent
so that sysfs has an idea of which input device is attached to
which hid device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Revert some changes done in 7746383868.
Revert all changes done in hidinput_calc_abs_res as it mistakingly used
"Unit" item exponent nibbles to affect resolution value. This wasn't
breaking resolution calculation of relevant axes of any existing
devices, though, as they have only one dimension to their units and thus
1 in the corresponding nible.
Revert to reading "Unit Exponent" item value as a signed integer in
hid_parser_global to fix reading specification-complying values. This
fixes resolution calculation of devices complying to the HID standard,
including Huion, KYE, Waltop and UC-Logic graphics tablets which have
their report descriptors fixed by the drivers.
Explanations follow.
There are two "unit exponents" in HID specification and it is important
not to mix them. One is the global "Unit Exponent" item and another is
nibble values in the global "Unit" item. See 6.2.2.7 Global Items.
The "Unit Exponent" value is just a signed integer and is used to scale
the integer resolution unit values, so fractions can be expressed.
The nibbles of "Unit" value are used to select the unit system (nibble
0), and presence of a particular basic unit type in the unit formula and
its *exponent* (or power, nibbles 1-6). And yes, the latter is in two
complement and zero means absence of the unit type.
Taking the representation example of (integer) joules from the
specification:
[mass(grams)][length(centimeters)^2][time(seconds)^-2] * 10^-7
the "Unit Exponent" would be -7 (or 0xF9, if stored as a byte) and the
"Unit" value would be 0xE121, signifying:
Nibble Part Value Meaning
----- ---- ----- -------
0 System 1 SI Linear
1 Length 2 Centimeters^2
2 Mass 1 Grams
3 Time -2 Seconds^-2
To give the resolution in e.g. hundredth of joules the "Unit Exponent"
item value should have been -9.
See also the examples of "Unit" values for some common units in the same
chapter.
However, there is a common misunderstanding about the "Unit Exponent"
value encoding, where it is assumed to be stored the same as nibbles in
"Unit" item. This is most likely due to the specification being a bit
vague and overloading the term "unit exponent". This also was and still
is proliferated by the official "HID Descriptor Tool", which makes this
mistake and stores "Unit Exponent" as such. This format is also
mentioned in books such as "USB Complete" and in Microsoft's hardware
design guides.
As a result many devices currently on the market use this encoding and
so the driver should support them.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When dealing with usage_index, be sure to properly use unsigned instead of
int to avoid overflows.
When working on report fields, always validate that their report_counts are
in bounds.
Without this, a HID device could report a malicious feature report that
could trick the driver into a heap overflow:
[ 634.885003] usb 1-1: New USB device found, idVendor=0596, idProduct=0500
...
[ 676.469629] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten
CVE-2013-2897
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hidinput_input_event() callback converts input events written from
userspace into HID reports and sends them to the device. We currently
implement this in every HID transport driver, even though most of them do
the same.
This provides a generic hidinput_input_event() implementation which is
mostly copied from usbhid. It uses a delayed worker to allow multiple LED
events to be collected into a single output event.
We use the custom ->request() transport driver callback to allow drivers
to adjust the outgoing report and handle the request asynchronously. If no
custom ->request() callback is available, we fall back to the generic raw
output report handler (which is synchronous).
Drivers can still provide custom hidinput_input_event() handlers (see
logitech-dj) if the generic implementation doesn't fit their needs.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Extend the comment explaining the condition for discarding
out-of-range values to clarify the cases in which devices don't
provide any logical min/max.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 6da7066906 introduced in 3.3
"HID: ignore absolute values which don't fit between logical min and max"
prevents some Posiflex touch screen to work because they do not provide
logical min and max for their buttons.
Thus, logical min and max are at 0, discarding the buttons events, and
preventing the device to report appropriate X Y.
Adding a check on "min < max" solves the problem.
Reported-by: Jan Kandziora <jjj@gmx.de>
Tested-by: Jan Kandziora <jjj@gmx.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
power_supply core has the bad habit of calling our battery callbacks
from within power_supply_register(). Furthermore, if the callbacks
fail with an unhandled error code, it will skip any uevent that it
might currently process.
So if HID-core registers battery devices, an "add" uevent is generated
and the battery callbacks are called. These will gracefully fail due
to timeouts as they might still hold locks on event processing. One
could argue that this should be fixed in power_supply core, but the
least we can do is to signal ENODATA so power_supply core will just
skip the property and continue with the uevent.
This fixes a bug where "add" and "remove" uevents are skipped for
battery devices. upower is unable to track these devices and currently
needs to ignore them.
This patch also overwrites any other error code. I cannot see any reason
why we should forward protocol- or I/O-errors to the power_supply core.
We handle these errors in hid_ll_driver later, anyway, so just skip
them. power_supply core cannot do anything useful with them, anyway,
and we avoid skipping important uevents and confusing user-space.
Thanks a lot to Daniel Nicoletti for pushing and investigating
on this.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Reported-by: Daniel Nicoletti <dantti12@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no need to register an input device containing no events.
This allows drivers using the quirk MULTI_INPUT to register one input
per report effectively used.
For backward compatibility, we need to add a quirk to request
this behavior.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
