Correct the comments in this driver. Set the CRTSCTS flag means
automatic flow control is enabled.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some vendors require special handling of the rx data from the USB
bulk endpoints. For that case provide an internal callback that
can overwrite it with a custom receive function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth controllers from Broadcom use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of having the driver generate the HCI Hardware Error event
manually, just call hci_reset_dev() to trigger the upper stack reset.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When constructing the event payload for the HCI_Hardware_Error event
message, use the HCI_EV_HARDWARE_ERROR define.
In addition rename the variables from hard_err to hw_err to clearly
indicate that this is about the hardware error and not a hard error.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
H5 Specification says:
If a SYNC message is received while in the Active State, it is
assumed that the peer device has reset. The local device should
therefore perform a full reset of the upper stack, and start Link
Establishment again at the Uninitialized State. Upon entering the
Active State, the first packet sent shall have its SEQ and ACK
numbers set to zero.
This patch resets the HCI H5 driver data/state to unitialized and
reports an HCI hardware error event to notify the upper stack that
HCI synchronization has been lost. H5 will be re-synchronized and
upper stack should generate an HCI Reset command.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pull vfs updates from Al Viro:
"The big thing in this pile is Eric's unmount-on-rmdir series; we
finally have everything we need for that. The final piece of prereqs
is delayed mntput() - now filesystem shutdown always happens on
shallow stack.
Other than that, we have several new primitives for iov_iter (Matt
Wilcox, culled from his XIP-related series) pushing the conversion to
->read_iter()/ ->write_iter() a bit more, a bunch of fs/dcache.c
cleanups and fixes (including the external name refcounting, which
gives consistent behaviour of d_move() wrt procfs symlinks for long
and short names alike) and assorted cleanups and fixes all over the
place.
This is just the first pile; there's a lot of stuff from various
people that ought to go in this window. Starting with
unionmount/overlayfs mess... ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (60 commits)
fs/file_table.c: Update alloc_file() comment
vfs: Deduplicate code shared by xattr system calls operating on paths
reiserfs: remove pointless forward declaration of struct nameidata
don't need that forward declaration of struct nameidata in dcache.h anymore
take dname_external() into fs/dcache.c
let path_init() failures treated the same way as subsequent link_path_walk()
fix misuses of f_count() in ppp and netlink
ncpfs: use list_for_each_entry() for d_subdirs walk
vfs: move getname() from callers to do_mount()
gfs2_atomic_open(): skip lookups on hashed dentry
[infiniband] remove pointless assignments
gadgetfs: saner API for gadgetfs_create_file()
f_fs: saner API for ffs_sb_create_file()
jfs: don't hash direct inode
[s390] remove pointless assignment of ->f_op in vmlogrdr ->open()
ecryptfs: ->f_op is never NULL
android: ->f_op is never NULL
nouveau: __iomem misannotations
missing annotation in fs/file.c
fs: namespace: suppress 'may be used uninitialized' warnings
...
Register offsets are different for SD8897 and newer chip SD8887.
We can not have common btmrvl_sdio_card_reg map for them.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When receiving USB interrupt, bulk or isochronous packet, they normally
come in fragments. So far the driver just handed each fragment off to
the hci_recv_fragment function of the Bluetooth core. That function is
however so specific that is does not belong in the core. This patch
implements the same reassembly logic in the driver.
In addition this fixes a long standing bug where multiple complete
packets are received within a single USB packet.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The actual packet reassembly should be done inside the driver. To allow
this to happen cleanly in future patches, split the fragment reception
into its own functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btusb driver has been around for a while now and it is time to
bring its coding style in sync with what has been done for the
Bluetooth subsystem and other drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The complete TX URB handling is done via a switch statement in the
btusb_send_frame function. To allow for more clear separation between
control, bulk and isoc URBs, split them into allocation and submission.
Previously the inc_tx function has been used for tracking in-flight
URB for HCI commands and ACL data packets. Convert that into a common
function that either submits the URB or queues it when needed.
This provides the flexibility to allow vendor specific hdev->send_frame
callbacks without having to duplicate the whole URB handling logic.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
All hdev->send() calls are these days done through a work queue. For the
btusb driver this means the btusb_send_frame() function. Because of this
we can safely use GFP_KERNEL for all memory allocations in this code
path.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Suspend could fail for some platforms because
btusb_suspend==> btusb_stop_traffic ==> usb_kill_anchored_urbs.
When btusb_bulk_complete returns before system suspend and resubmits
an URB, the system cannot enter suspend state.
Signed-off-by: Champion Chen <champion_chen@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
bt3c_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedefs for nsh_t and
dtl1_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case for dtl1_info_t
and a similar patch finds the nsh_t case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
btuart_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
bluecard_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In this expression: seq = (seq - 1) % 8
seq (u8) is implicitly converted to an int in the arithmetic operation.
So if seq value is 0, operation is ((0 - 1) % 8) => (-1 % 8) => -1.
The new seq value is 0xff which is an invalid ACK value, we expect 0x07.
It leads to frequent dropped ACK and retransmission.
Fix this by using '&' binary operator instead of '%'.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
btmrvl_add_card() function calls kthread_run that might return error
(e.g. if current thread is killed). If one tries to use the error
value as a pointer then invalid memory access oops happens.
Check kthread_run() return value, if it is an error then release resources
correctly.
TEST=boot computer with BT modules enabled. I see the error message that
BT device initialization failed. Now kernel does not crash. Hint: to enable
BT run 'rmmod btmrvl_sdio; modprobe btmrvl_sdio'
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
