Incoming requests shouldn't require a local exchange if we're
just going to reply with one or two frames and don't expect
anything further. Don't allocate exchanges for such requests
until requested by the upper-layer protocol.
The sequence is always NULL for new requests, so remove
that as an argument to request handlers.
Also change the first argument to lport->tt.seq_els_rsp_send
from the sequence pointer to the received frame pointer, to
supply the exchange IDs and destination ID info.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For incoming ELS and FCP requests, we often don't require an
exchange and sequence, however, sometimes we do. For those cases,
(primarily FCP requests for targets) add a function to set up
the exchange and sequence.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add functions to fill in an FC header given a request header.
These reduces code lines in fc_lport and fc_rport and works
without an exchange/sequence assigned.
fc_fill_reply_hdr() fills a header for a final reply frame.
fc_fill_hdr() which is similar but allows specifying the
f_ctl parameter.
Add defines for F_CTL values FC_FCTL_REQ and FC_FCTL_RESP.
These can be used for most request and response sequences.
v2 of patch adds a line to copy the frame encapsulation
info from the received frame.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To pave the way for eliminating exchanges from incoming requests,
add simple inline fc_frame_sid() and fc_frame_did() functions
which get the FC_IDs from the frame header. This can be almost
as efficient as getting them from the sequence/exchange.
Move ntohll, htonll, ntoh24 and hton24 to <scsi/fc_frame.h>
since we need them there and that's included by <scsi/libfc.h>
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The LOGO state hasn't been used in a while, except in a brief
transition to DELETE state while holding the rport mutex.
All port LOGO responses have been ignored as well as any timeout
if we don't get a response.
So this patch just removes LOGO state and simplifies the response handler.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When an exchange is received with a FIP encapsulation, we need
to know that the response must be sent via FIP and what the original
ELS opcode was. This becomes important for VN2VN mode, where we may
receive FLOGI or LOGO from several peer VN_ports, and the LS_ACC or
LS_RJT must be sent FIP-encapsulated with the correct sub-type.
Add a field to the struct fc_frame, fr_encaps, to indicate the
encapsulation values. That term is chosen to be neutral and
LLD-agnostic in case non-FCoE/FIP LLDs might find it useful.
The frame fr_encaps is transferred from the ingress frame to the
exchange by fc_exch_recv_req(), and back to the outgoing frame
by fc_seq_send().
This is taking the last byte in the skb->cb array. If needed,
we could combine the info in sof, eof, flags, and encaps
together into one field, but it'd be better to do that if
and when its needed.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The FIP proposal for VN_port to VN_port point-to-multipoint
operation requires a FLOGI be sent to each remote port.
The FLOGI is sent with the assigned S_ID and D_IDs of the
local and remote ports. This and the response get
FIP-encapsulated for Ethernet.
Add FLOGI state to the remote port state machine.
This will be skipped if not in point-to-multipoint mode.
To reduce a little duplication between PLOGI and FLOGI
response handling, added fc_rport_login_complete(), which
handles the parameters for the rdata struct.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For VN_port to VN_port mode, the transport sets the port_id and
there's no lport FLOGI. This is similar to FC loop mode.
Add a point_to_multipoint flag that indicates the local port is in
point-to-multipoint mode. This skips FLOGI and discovery.
It also skips resetting the port_id on resets other than link down.
Add function fc_lport_set_local_id() that sets the local port_id.
This is called by libfcoe on behalf of the low-level driver
to set the port_id when the link comes up.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For VN_port to VN_port mode, FIP will do discovery and needs a
way to find its state from the local port or discovery structure.
It seems that any other LLD that implements its own discovery
would also need something like this.
Replace disc->lport with disc->priv, and use container_of to
find the lport. We could use disc->priv for that, but
container_of is smaller and faster.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add pre-zeroed space after the allocation for fc_rport_priv
for use by the lower-level driver.
This is primarily for VN2VN FIP mode, but could be used in
other ways someday.
The space required is specified in lport->rport_priv_size.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To allow LLD to do lookups on rports without grabbing a mutex,
make them RCU-safe. The caller of lport->tt.rport_lookup will
have the choice of holding disc_mutex or the rcu_read_lock().
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remote ports were restarting indefinitely after getting
rejects in PRLI.
Fix by adding a counter of restarts and limiting that with
the port login retry limit as well.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch somewhat combines two fixes to remote port handing in libfc.
The first problem was that rport work could be queued on a deleted
and freed rport. This is handled by not resetting rdata->event
ton NONE if the rdata is about to be deleted.
However, that fix led to the second problem, described by
Bhanu Gollapudi, as follows:
> Here is the sequence of events. T1 is first LOGO receive thread, T2 is
> fc_rport_work() scheduled by T1 and T3 is second LOGO receive thread and
> T4 is fc_rport_work scheduled by T3.
>
> 1. (T1)Received 1st LOGO in state Ready
> 2. (T1)Delete port & enter to RESTART state.
> 3. (T1)schdule event_work, since event is RPORT_EV_NONE.
> 4. (T1)set event = RPORT_EV_LOGO
> 5. (T1)Enter RESTART state as disc_id is set.
> 6. (T2)remember to PLOGI, and set event = RPORT_EV_NONE
> 6. (T3)Received 2nd LOGO
> 7. (T3)Delete Port & enter to RESTART state.
> 8. (T3)schedule event_work, since event is RPORT_EV_NONE.
> 9. (T3)Enter RESTART state as disc_id is set.
> 9. (T3)set event = RPORT_EV_LOGO
> 10.(T2)work restart, enter PLOGI state and issues PLOGI
> 11.(T4)Since state is not RESTART anymore, restart is not set, and the
> event is not reset to RPORT_EV_NONE. (current event is RPORT_EV_LOGO).
> 12. Now, PLOGI succeeds and fc_rport_enter_ready() will not schedule
> event_work, and hence the rport will never be created, eventually losing
> the target after dev_loss_tmo.
So, the problem here is that we were tracking the desire for
the rport be restarted by state RESTART, which was otherwise
equivalent to DELETE. A contributing factor is that we dropped
the lock between steps 6 and 10 in thread T2, which allows the
state to change, and we didn't completely re-evaluate then.
This is hopefully corrected by the following minor redesign:
Simplify the rport restart logic by making the decision to
restart after deleting the transport rport. That decision
is based on a new STARTED flag that indicates fc_rport_login()
has been called and fc_rport_logoff() has not been called
since then. This replaces the need for the RESTART state.
Only restart if the rdata is still in DELETED state
and only if it still has the STARTED flag set.
Also now, since we clear the event code much later in the
work thread, allow for the possibility that the rport may
have become READY again via incoming PLOGI, and if so,
queue another event to handle that.
In the problem scenario, the second LOGO received will
cause the LOGO event to occur again.
Reported-by: Bhanu Gollapudi <bprakash@broadcom.com>
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch creates a port_id member in struct fc_lport.
This allows libfc to just deal with fc_lport instances
instead of calling into the fc_host to get the port_id.
This change helps in only using symbols necessary for
operation from the libfc structures. libfc still needs
to change the fc_host_port_id() if the port_id changes
so the presentation layer (scsi_transport_fc) can provide
the user with the correct value, but libfc shouldn't
rely on the presentation layer for operational values.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
hton24(p + 3, value) would fail to compile because
p + 3[0] is not a valid expression.
Went ahead and converted hton24 and ntoh24 to inline
functions, which is better because the parameters
are evalutated only once.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the kernel is configured for preemption, using smp_processor_id()
when preemption is enabled causes a warning backtrace and is wrong
since we could move off of that CPU as soon as we get the ID,
and we would be referencing the wrong CPU, and possibly an invalid one
if it could be hotswapped out.
Remove the fc_lport_get_stats() function and explicitly use per_cpu_ptr()
to get the statistics. Where preemption has been disabled by holding
a _bh lock continue to use smp_processor_id(), but otherwise use
get_cpu()/put_cpu().
In fcoe_recv_frame() also changed the cases where we return in the
middle to do a goto to the code which bumps ErrorFrames and does
a put_cpu(). Two of these cases didn't bump ErrorFrames before, but
doing so is harmless because they "can't happen", due to prior length
checks.
Also rearranged code in fcoe_recv_frame() to have only one call to
fc_exch_recv(). It's just as efficient and saves a call to put_cpu().
In fc_fcp.c, adjusted a FIXME comment for code which doesn't need fixing.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add a member function pointer as get_lesb to libfc_function_template so LLD
can fill the LESB based on its own statistics. For fcoe, it fills the LESB
as a fcoe_fc_els_lesb struct according to FC-BB-5.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FC-BB-5 Rev2.0, Clause 7.10 extends the FC-LS-3 LESB for FC-BB_E. We are
already tracking Link Failure Count so add the rest in this patch.
For VLinkFailureCount and MissDiscAdvCount, they are part of the per-cpu
fcoe_dev_stats. For SymbolErrorCount, ErroredBlockCount, and FCSErrorCount,
they are defined in IEEE 802.3-2008 and are per LLD. They are expected to
come from LLD.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Customers and certification tests have pointed out that we don't
show up on the switch management software as an initiator.
On some MDS switches 'show fcns database' command shows libfc
initiators as 'fcp' not 'fcp:init' like other initiators.
On others switches, I think the switch gets the features by doing a PRLI,
but it may be only certain models or under certain configurations.
Fix this by registering our FC4 features with the RFF_ID CT request
after local port login and after the RFT_ID.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is to notify the LLD when an FC_ID is assigned to the local port.
The fnic driver needs to push the assigned FC_ID to firmware.
It currently does this by intercepting the FLOGI responses, and
in order to make that code more common with FIP and NPIV, it
makes more sense to wait until the local port has completely
handled the FLOGI or FDISC response. Also, when we fix
point-to-point FC_ID assignment, we'll need this callback as well.
Add a call to the libfc template, which is called whenever
the local port FC_ID is being assigned. It defaults to
fc_lport_set_fid(), supplied by libfc.
As additional benefit of this function, the LLD may determine
the MAC address that caused the change by looking at the received frame.
We also print the assigned port ID as long as it isn't 0.
Setting port ID to 0 happens often in reset while retrying FLOGI,
and would be uninteresting. This replaces the previous message
which didn't identify the host adapter instance.
patch v2 note: changed one word in a comment. "intercepted" -> "provided".
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch makes a variety of cleanup changes to all libfc files.
This patch adds kernel-doc headers to all functions lacking them
and attempts to better format existing headers. It also add kernel-doc
headers to structures.
This patch ensures that the current naming conventions for local ports,
remote ports and remote port private data is upheld in the following
manner.
struct instance (i.e. variable name)
--------------------------------------------------
fc_lport lport
fc_rport rport
fc_rport_libfc_priv rpriv
fc_rport_priv rdata
I also renamed dns_rp and ptp_rp to dns_rdata and ptp_rdata
respectively.
I used emacs 'indent-region' and 'tabify' on all libfc files
to correct spacing alignments.
I feel sorry for anyone attempting to review this patch.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is the Open-FCoE implementation of the FC
passthrough support via bsg interface.
Passthrough support is added to both N_Ports and
VN_Ports.
Signed-off-by: Steve Ma <steve.ma@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
