actual_length should also be a u32 and not a signed value. This patch
changes this field to be 'u32' to prevent any potential negative
conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roel Kluin pointed out that transfer_buffer_lengths in struct urb was
declared as an 'int'. This patch changes this field to be 'u32' to
prevent any potential negative conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To permit a userspace application to associate with WUSB devices
using numeric association, control transfers to unauthenticated WUSB
devices must be allowed.
This requires that wusbcore correctly sets the device state to
UNAUTHENTICATED, DEFAULT and ADDRESS and that control transfers can be
performed to UNAUTHENTICATED devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1206) is the first step in converting usb-storage's
subdrivers into separate modules. It makes the following large-scale
changes:
Remove a bunch of unnecessary #ifdef's from usb_usual.h.
Not truly necessary, but it does clean things up.
Move the USB device-ID table (which is duplicated between
libusual and usb-storage) into its own source file,
usual-tables.c, and arrange for this to be linked with
either libusual or usb-storage according to whether
USB_LIBUSUAL is configured.
Add to usual-tables.c a new usb_usual_ignore_device()
function to detect whether a particular device needs to be
managed by a subdriver and not by the standard handlers
in usb-storage.
Export a whole bunch of functions in usb-storage, renaming
some of them because their names don't already begin with
"usb_stor_". These functions will be needed by the new
subdriver modules.
Split usb-storage's probe routine into two functions.
The subdrivers will call the probe1 routine, then fill in
their transport and protocol settings, and then call the
probe2 routine.
Take the default cases and error checking out of
get_transport() and get_protocol(), which run during
probe1, and instead put a check for invalid transport
or protocol values into the probe2 function.
Add a new probe routine to be used for standard devices,
i.e., those that don't need a subdriver. This new routine
checks whether the device should be ignored (because it
should be handled by ub or by a subdriver), and if not,
calls the probe1 and probe2 functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NOP transceiver is used by all the usb transceiver which are mostly
autonomous and doesn't require any programming or which are built
into the usb ip itself.NOP transceiver only allocates the memory
for struct xceiv and calls otg_set_transceiver() so function call
to otg_get_transceiver() will return a valid transceiver.
NOP transceiver device should be registered by calling
usb_nop_xceiv_register() from platform files.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a flag into the usb serial layer to tell drivers
that their URBs are killed due to suspension. That is necessary to let
drivers know whether they should report an error back.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Hi Greg,
this is for 2.6.30. Patches to use this in drivers are under development.
Regards
Oliver
The functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_is_isoc_in(epd)
usb_endpoint_is_isoc_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
are moved from include/linux/usb.h to include/linux/usb/ch9.h.
include/linux/usb/ch9.h makes more sense for these functions because they
only depend on constants that are defined in this file.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call usb_gadget_vbus_connect() and ...disconnect() from a
workqueue rather than from an irq handler, allowing msleep()
calls in vbus_session. Update kerneldoc to match.
[ dbrownell@users.sourceforge.net: more kerneldoc updates ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently the Configuration and Interface strings aren't used as
often as the Vendor, Product, and Serial strings. In at least one
device (a Saitek Cyborg Gold 3D joystick), attempts to read the
Configuration string cause the device to stop responding to Control
requests.
This patch (as1226) adds a quirks flag, telling the kernel not to
read a device's Configuration or Interface strings, together with a
new quirk for the offending joystick.
Reported-by: Melchior FRANZ <melchior.franz@gmail.com>
Tested-by: Melchior FRANZ <melchior.franz@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.28 and 2.6.29, nothing earlier]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
ucc_geth: Fix oops when using fixed-link support
dm9000: locking bugfix
net: update dnet.c for bus_id removal
dnet: DNET should depend on HAS_IOMEM
dca: add missing copyright/license headers
nl80211: Check that function pointer != NULL before using it
sungem: missing net_device_ops
be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycle
be2net: replenish when posting to rx-queue is starved in out of mem conditions
bas_gigaset: correctly allocate USB interrupt transfer buffer
smsc911x: reset last known duplex and carrier on open
sh_eth: Fix mistake of the address of SH7763
sh_eth: Change handling of IRQ
netns: oops in ip[6]_frag_reasm incrementing stats
net: kfree(napi->skb) => kfree_skb
net: fix sctp breakage
ipv6: fix display of local and remote sit endpoints
net: Document /proc/sys/net/core/netdev_budget
tulip: fix crash on iface up with shirq debug
virtio_net: Make virtio_net support carrier detection
...
In two dca files copyright and license headers are missing.
This patch adds them there.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since creating a device node is normally an operation requiring special
privilege, Igor Zhbanov points out that it is surprising (to say the
least) that a client can, for example, create a device node on a
filesystem exported with root_squash.
So, make sure CAP_MKNOD is among the capabilities dropped when an nfsd
thread handles a request from a non-root user.
Reported-by: Igor Zhbanov <izh1979@gmail.com>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
This patch skips the delivery of conntrack events if the packet
was drop due to a race condition in the conntrack insertion.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* master.kernel.org:/home/rmk/linux-2.6-arm: (23 commits)
[ARM] Fix virtual to physical translation macro corner cases
[ARM] update mach-types
[ARM] 5421/1: ftrace: fix crash due to tracing of __naked functions
MX1 fix include
[ARM] 5419/1: ep93xx: fix build warnings about struct i2c_board_info
[ARM] 5418/1: restore lr before leaving mcount
ARM: OMAP: board-omap3beagle: set i2c-3 to 100kHz
ARM: OMAP: Allow I2C bus driver to be compiled as a module
ARM: OMAP: sched_clock() corrected
ARM: OMAP: Fix compile error if pm.h is included
[ARM] orion5x: pass dram mbus data to xor driver
[ARM] S3C64XX: Fix s3c64xx_setrate_clksrc
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/irq.c
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/s3c6400-clock.c
[ARM] S3C64XX: Fix USB host clock mux list
[ARM] S3C64XX: Fix name of USB host clock.
[ARM] S3C64XX: Rename IRQ_UHOST to IRQ_USBH
[ARM] S3C64XX: Do gpiolib configuration earlier
[ARM] S3C64XX: Staticise s3c64xx_init_irq_eint()
[ARM] SMDK6410: Declare iodesc table static
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (31 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k4.
[SCSI] qla2xxx: Correct overwrite of pre-assigned init-control-block structure size.
[SCSI] qla2xxx: Correct truncation in return-code status checking.
[SCSI] qla2xxx: Correct vport delete bug.
[SCSI] qla2xxx: Use correct value for max vport in LOOP topology.
[SCSI] qla2xxx: Correct address range checking for option-rom updates.
[SCSI] fcoe: Change fcoe receive thread nice value from 19 (lowest priority) to -20
[SCSI] fcoe: fix handling of pending queue, prevent out of order frames (v3)
[SCSI] fcoe: Out of order tx frames was causing several check condition SCSI status
[SCSI] fcoe: fix kfree(skb)
[SCSI] fcoe: ETH_P_8021Q is already in if_ether and fcoe is not using it anyway
[SCSI] libfc: do not change the fh_rx_id of a recevied frame
[SCSI] fcoe: Correct fcoe_transports initialization vs. registration
[SCSI] fcoe: Use setup_timer() and mod_timer()
[SCSI] libfc, fcoe: Remove unnecessary cast by removing inline wrapper
[SCSI] libfc, fcoe: Cleanup function formatting and minor typos
[SCSI] libfc, fcoe: Fix kerneldoc comments
[SCSI] libfc: Cleanup libfc_function_template comments
[SCSI] libfc: check for err when recv and state is incorrect
[SCSI] libfc: rename rp to rdata in fc_disc_new_target()
...
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Fix the fix to Bugzilla #11061, when IPv6 isn't defined...
SUNRPC: xprt_connect() don't abort the task if the transport isn't bound
SUNRPC: Fix an Oops due to socket not set up yet...
Bug 11061, NFS mounts dropped
NFS: Handle -ESTALE error in access()
NLM: Fix GRANT callback address comparison when IPv6 is enabled
NLM: Shrink the IPv4-only version of nlm_cmp_addr()
NFSv3: Fix posix ACL code
NFS: Fix misparsing of nfsv4 fs_locations attribute (take 2)
SUNRPC: Tighten up the task locking rules in __rpc_execute()
dma_map_sg could return a value different to 'nents' argument of
dma_map_sg so the ide stack needs to save it for the later usage
(e.g. for_each_sg).
The ide stack also needs to save the original sg_nents value for
pci_unmap_sg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
[bart: backport to Linus' tree]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
cpumask: mm_cpumask for accessing the struct mm_struct's cpu_vm_mask.
cpumask: tsk_cpumask for accessing the struct task_struct's cpus_allowed.
This allows us to change the representation (to a dangling bitmap or
cpumask_var_t) without breaking all the callers: they can use
mm_cpumask() now and won't see a difference as the changes roll into
linux-next.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This allows us to change the representation (to a dangling bitmap or
cpumask_var_t) without breaking all the callers: they can use
tsk_cpumask() now and won't see a difference as the changes roll into
linux-next.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Comparing the layouts of struct detail_pixel_timing with
x.org's struct detailed_timings and how those are handled,
it appears that the hsync_positive and vsync_positive
fields are backwards.
This patch fixes https://bugs.freedesktop.org/show_bug.cgi?id=20019
for me. It was tested on 2 monitors, LG FLATRON L225WS 22" and
a YAKUMO 17" for which more details are unknown.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
