Check truncate_if_32bit() on final write to nip.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No code changes, just documenting what's happening a little better.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Uprobes uses emulate_step in sstep.c, but we haven't explicitly specified
the dependency. On pseries HAVE_HW_BREAKPOINT protects us, but 44x has no
such luxury.
Consolidate other users that depend on sstep and create a new config option.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: linuxppc-dev@ozlabs.org
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Finally remove the two level TOC and build with -mcmodel=medium.
Unfortunately we can't build modules with -mcmodel=medium due to
the tricks the kernel module loader plays with percpu data:
# -mcmodel=medium breaks modules because it uses 32bit offsets from
# the TOC pointer to create pointers where possible. Pointers into the
# percpu data area are created by this method.
#
# The kernel module loader relocates the percpu data section from the
# original location (starting with 0xd...) to somewhere in the base
# kernel percpu data space (starting with 0xc...). We need a full
# 64bit relocation for this to work, hence -mcmodel=large.
On older kernels we fall back to the two level TOC (-mminimal-toc)
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We don't do the real store operation for kprobing 'stwu Rx,(y)R1'
since this may corrupt the exception frame, now we will do this
operation safely in exception return code after migrate current
exception frame below the kprobed function stack.
So we only update gpr[1] here and trigger a thread flag to mask
this.
Note we should make sure if we trigger kernel stack over flow.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
patch_instruction() can be called very early on ppc32, when the kernel
isn't yet running at it's linked address. That can cause the !
is_kernel_addr() test in __put_user() to trip and call might_sleep()
which is very bad at that point during boot.
Use a lower level function instead for now, at least until we get to
rework ppc32 boot process to do the code patching later, like ppc64
does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The enhanced prefetch hint patches corrupt the condition register
that was used to check if we are in interrupt. Fix this by using cr1.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
"powerpc: Use enhanced touch instructions in POWER7
copy_to_user/copy_from_user" was applied twice. Remove one.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This allows the linker to know that calls to them do not need to switch
TOC and stop errors like the following when linking large configurations:
powerpc64-linux-ld: drivers/built-in.o: In function `.gpiochip_is_requested':
(.text+0x4): sibling call optimization to `_savegpr0_29' does not allow automatic multiple TOCs; recompile with -mminimal-toc or -fno-optimize-sibling-calls, or make `_savegpr0_29' extern
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These macros are using integers where they could be using logical
names since they take registers.
We are going to enforce this soon, so fix these up now.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mtocrf define is just a wrapper around the real instructions so we can
just use real register names here (ie. lower case).
Also remove braces in macro so this is possible.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge the defines of STACKFRAMESIZE, STK_REG, STK_PARAM from different
places.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anything that uses a constructed instruction (ie. from ppc-opcode.h),
need to use the new R0 macro, as %r0 is not going to work.
Also convert usages of macros where we are just determining an offset
(usually for a load/store), like:
std r14,STK_REG(r14)(r1)
Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since
it's just calculating an offset.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I blame Mikey for this. He elevated my slightly dubious testcase:
to benchmark status. And naturally we need to be number 1 at creating
zeros. So lets improve __clear_user some more.
As Paul suggests we can use dcbz for large lengths. This patch gets
the destination cacheline aligned then uses dcbz on whole cachelines.
Before:
10485760000 bytes (10 GB) copied, 0.414744 s, 25.3 GB/s
After:
10485760000 bytes (10 GB) copied, 0.268597 s, 39.0 GB/s
39 GB/s, a new record.
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Olof Johansson <olof@lixom.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement a POWER7 optimised memcpy using VMX and enhanced prefetch
instructions.
This is a copy of the POWER7 optimised copy_to_user/copy_from_user
loop. Detailed implementation and performance details can be found in
commit a66086b819 (powerpc: POWER7 optimised
copy_to_user/copy_from_user using VMX).
I noticed memcpy issues when profiling a RAID6 workload:
.memcpy
.async_memcpy
.async_copy_data
.__raid_run_ops
.handle_stripe
.raid5d
.md_thread
I created a simplified testcase by building a RAID6 array with 4 1GB
ramdisks (booting with brd.rd_size=1048576):
# mdadm -CR -e 1.2 /dev/md0 --level=6 -n4 /dev/ram[0-3]
I then timed how long it took to write to the entire array:
# dd if=/dev/zero of=/dev/md0 bs=1M
Before: 892 MB/s
After: 999 MB/s
A 12% improvement.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Version 2.06 of the POWER ISA introduced enhanced touch instructions,
allowing us to specify a number of attributes including the length of
a stream.
This patch adds a software stream for both loads and stores in the
POWER7 copy_tofrom_user loop. Since the setup is quite complicated
and we have to use an eieio to ensure correct ordering of the "GO"
command we only do this for copies above 4kB.
To quantify any performance improvements we need a working set
bigger than the caches so we operate on a 1GB file:
# dd if=/dev/zero of=/tmp/foo bs=1M count=1024
And we compare how fast we can read the file:
# dd if=/tmp/foo of=/dev/null bs=1M
before: 7.7 GB/s
after: 9.6 GB/s
A 25% improvement.
The worst case for this patch will be a completely L1 cache contained
copy of just over 4kB. We can test this with the copy_to_user
testcase we used to tune copy_tofrom_user originally:
http://ozlabs.org/~anton/junkcode/copy_to_user.c
# time ./copy_to_user2 -l 4224 -i 10000000
before: 6.807 s
after: 6.946 s
A 2% slowdown, which seems reasonable considering our data is unlikely
to be completely L1 contained.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement a POWER7 optimised copy_page using VMX and enhanced
prefetch instructions. We use enhanced prefetch hints to prefetch
both the load and store side. We copy a cacheline at a time and
fall back to regular loads and stores if we are unable to use VMX
(eg we are in an interrupt).
The following microbenchmark was used to assess the impact of
the patch:
http://ozlabs.org/~anton/junkcode/page_fault_file.c
We test MAP_PRIVATE page faults across a 1GB file, 100 times:
# time ./page_fault_file -p -l 1G -i 100
Before: 22.25s
After: 18.89s
17% faster
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Subsequent patches will add more VMX library functions and it makes
sense to keep all the c-code helper functions in the one file.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Version 2.06 of the POWER ISA introduced enhanced touch instructions,
allowing us to specify a number of attributes including the length of
a stream.
This patch adds a software stream for both loads and stores in the
POWER7 copy_tofrom_user loop. Since the setup is quite complicated
and we have to use an eieio to ensure correct ordering of the "GO"
command we only do this for copies above 4kB.
To quantify any performance improvements we need a working set
bigger than the caches so we operate on a 1GB file:
# dd if=/dev/zero of=/tmp/foo bs=1M count=1024
And we compare how fast we can read the file:
# dd if=/tmp/foo of=/dev/null bs=1M
before: 7.7 GB/s
after: 9.6 GB/s
A 25% improvement.
The worst case for this patch will be a completely L1 cache contained
copy of just over 4kB. We can test this with the copy_to_user
testcase we used to tune copy_tofrom_user originally:
http://ozlabs.org/~anton/junkcode/copy_to_user.c
# time ./copy_to_user2 -l 4224 -i 10000000
before: 6.807 s
after: 6.946 s
A 2% slowdown, which seems reasonable considering our data is unlikely
to be completely L1 contained.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I noticed __clear_user high up in a profile of one of my RAID stress
tests. The testcase was doing a dd from /dev/zero which ends up
calling __clear_user.
__clear_user is basically a loop with a single 4 byte store which
is horribly slow. We can do much better by aligning the desination
and doing 32 bytes of 8 byte stores in a loop.
The following testcase was used to verify the patch:
http://ozlabs.org/~anton/junkcode/stress_clear_user.c
To show the improvement in performance I ran a dd from /dev/zero
to /dev/null on a POWER7 box:
Before:
# dd if=/dev/zero of=/dev/null bs=1M count=10000
10485760000 bytes (10 GB) copied, 3.72379 s, 2.8 GB/s
After:
# time dd if=/dev/zero of=/dev/null bs=1M count=10000
10485760000 bytes (10 GB) copied, 0.728318 s, 14.4 GB/s
Over 5x faster.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For ftrace to use the patch_instruction code, it needs to check for
faults on write. Ftrace updates code all over the kernel, and we need to
know if code is updated or not due to protections that are placed on
some portions of the kernel. If ftrace does not detect a fault, it will
error later on, and it will be much more difficult to find the problem.
By changing patch_instruction() to detect faults, then ftrace will be
able to make use of it too.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is much the same as for SPARC except that we can do the find_zero()
function more efficiently using the count-leading-zeroes instructions.
Tested on 32-bit and 64-bit PowerPC.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove CONFIG_POWER4_ONLY, the option is badly named and only does two
things:
- It wraps the MMU segment table code. With feature fixups there is
little downside to compiling this in.
- It uses the newer mtocrf instruction in various assembly functions.
Instead of making this a compile option just do it at runtime via
a feature fixup.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
