Pull clk driver fix from Mike Turquette:
"Single fix for a clock driver merged in 3.14-rc1. Without this fix
the CPU frequency cannot be scaled"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: shmobile: rcar-gen2: Use kick bit to allow Z clock frequency change
The Z clock frequency change is effective only after setting the kick
bit located in the FRQCRB register.
Without that, the CA15 CPUs clock rate will never change.
Fix that by checking if the kick bit is cleared and enable it to make
the clock rate change effective. The bit is cleared automatically upon
completion.
Signed-off-by: Benoit Cousson <bcousson+renesas@baylibre.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The Nomadik debugfs screws up multiplatform boots if debugfs
is enabled on the multiplatform image, since it's a simple
initcall that is unconditionally executed and reads from certain
memory locations.
Fix this by checking that the driver has been properly
initialized, so a base offset to the Nomadik SRC controller
exists, before proceeding to register debugfs files.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Fixes stray access to undefined registers, use of wrong clock parents &
running clocks at wrong rates. All of these issues cause regressions in
the form of boards that are unable to boot or crash and die horrible
deaths.
Tegra124 does not have gr2d and gr3d clocks. They have been replaced by the
vic03 and gpu clocks respectively.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
mvebu clock fixes for v3.14
- kirkwood, dove, armada-xp, armada-370
- force clock init order broken by sorting DT ocp nodes by address
- fixes boot failures on affected platforms
The qspi clock divisor is incorrectly set to twice the value it should
have, possibly because it has been computed based on PLL1 as the clock
parent instead of PLL1 / 2 (the datasheets specifies the qspi nominal
frequencies, not the divisor values). Fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
When requesting a rate less than the minimum clock rate for a divider,
use the maximum divider value instead of bailing out with an error.
This matches the behavior of the generic clock divider.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
When pll_x is the parent of cclk_lp, PLLX_DIV2_BYPASS_LP determines
whether cclk_lp output is divided by 2. Set TEGRA_DIVIDER_2 so that
the clk_super driver is aware of this.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
The sdmmc clocks on Tegra114 and Tegra124 are 3-bit wide muxes with
6 parents. Add support for tegra_clk_sdmmc*_8 and switch Tegra114
and Tegra124 to use these clocks instead.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
The host1x clock on Tegra124 is a 3-bit wide mux with 6 parents.
Change thte id to tegra_clk_host1x_8 so that the correct clock gets
registered.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Set correct pll_d2_out0 divider and correct the p div values for pll_d2.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
PLLD was using the same mnp table as PLLP. Fix it to use its own
table which is different from PLLP's.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
This table had settings for 216MHz, but PLLP is (and is supposed to be)
configured at 408MHz. If that table is used and PLLP_BASE_OVRRIDE is
not set, the kernel will panic in clk_pll_recalc_rate().
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
The clk_init_data struct is allocated in the stack. All members of
this struct should be initialized before using otherwise it will
lead to unpredictable situation as it can contain garbage.
Ultimately the clk->flag field contains garbage. In my case it leads
that flag CLK_IGNORE_UNUSED is set for most of clocks. As result a
bunch of unused clocks cannot be disabled.
So initialize flags in this structure too.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Init order of CLK_OF_DECLARE'd drivers depends on compile order.
Unfortunately, clk_of_init does not allow drivers to return errors,
e.g. -EPROBE_DEFER if parent clocks have not been registered, yet.
To avoid init order woes for MVEBU clock drivers, we take care of
proper init order ourselves. This patch joins core-clk and gating-clk
init to maintain proper init order.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Init order of CLK_OF_DECLARE'd drivers depends on compile order.
Unfortunately, clk_of_init does not allow drivers to return errors,
e.g. -EPROBE_DEFER if parent clocks have not been registered, yet.
To avoid init order woes for MVEBU clock drivers, we take care of
proper init order ourselves. This patch joins core-clk and gating-clk
init to maintain proper init order.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Init order of CLK_OF_DECLARE'd drivers depends on compile order.
Unfortunately, clk_of_init does not allow drivers to return errors,
e.g. -EPROBE_DEFER if parent clocks have not been registered, yet.
To avoid init order woes for MVEBU clock drivers, we take care of
proper init order ourselves. This patch joins core-clk and gating-clk
init to maintain proper init order.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
