This implements a SHOULD from RFC 4340, 7.5.4:
"To protect against denial-of-service attacks, DCCP implementations SHOULD
impose a rate limit on DCCP-Syncs sent in response to sequence-invalid packets,
such as not more than eight DCCP-Syncs per second."
The rate-limit is maintained on a per-socket basis. This is a more stringent
policy than enforcing the rate-limit on a per-source-address basis and
protects against attacks with forged source addresses.
Moreover, the mechanism is deliberately kept simple. In contrast to
xrlim_allow(), bursts of Sync packets in reply to sequence-invalid packets
are not supported. This foils such attacks where the receipt of a Sync
triggers further sequence-invalid packets. (I have tested this mechanism against
xrlim_allow algorithm for Syncs, permitting bursts just increases the problems.)
In order to keep flexibility, the timeout parameter can be set via sysctl; and
the whole mechanism can even be disabled (which is however not recommended).
The algorithm in this patch has been improved with regard to wrapping issues
thanks to a suggestion by Arnaldo.
Commiter note: Rate limited the step 6 DCCP_WARN too, as it says we're
sending a sync.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This fixes the code to correspond to RFC 4340, 7.5.4, which states the
exception that a Sync received in state REQUEST generates a Reset (not
a SyncAck).
To achieve this, only a small change is required. Since
dccp_rcv_request_sent_state_process() already uses the correct Reset Code
number 4 ("Packet Error"), we only need to shift the if-statement a few
lines further down.
(To test this case: replace DCCP_PKT_RESPONSE with DCCP_PKT_SYNC
in dccp_make_response.)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This updates sequence number checking with regard to RFC 4340, 7.5.4.
Missing in the code was an exception for sequence-invalid Reset packets,
which get a Sync acknowledging GSR, instead of (as usual) P.seqno.
This can lead to an oscillating ping-pong flood of Reset packets.
In fact, it has been observed on the wire as follows:
1. client establishes connection to server;
2. before server can write to client, client crashes without notifying
the server (NB: now no longer possible due to ABORT function);
3. server sends DCCP-Data packet (has no ackno);
4. client generates Reset "No Connection", seqno=0, increments seqno;
5. server replies with Sync, using ackno = P.seqno;
6. client generates Reset "No Connection" with seqno = ackno + 1;
7. goto (5).
The difference is that now in (5) the server uses GSR. This causes the
Reset sent by the client in (6) to become sequence-valid, so that in (7)
the vicious circle is broken; the Reset is then enqueued and causes the
socket to enter TIMEWAIT state.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is in part required by the next patch; it
* replaces 6 instances of `DCCP_SKB_CB(skb)->dccpd_seq' with `seqno';
* replaces 7 instances of `DCCP_SKB_CB(skb)->dccpd_ack_seq' with `ackno';
* replaces 1 use of dccp_inc_seqno() by unfolding `ADD48' macro in place.
No changes in algorithm, all changes are text replacement/substitution.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The third parameter of dccp_sample_rtt now becomes useless and is removed.
Also combined the subtraction of the timestamp echo and the elapsed time.
This is safe, since (a) presence of timestamp echo is tested first and (b)
elapsed time is either present and non-zero or it is not set and equals 0
due to the memset in dccp_parse_options.
To avoid measuring option-processing time, the timestamp for measuring the
initial Request/Response RTT sample is taken directly when the function is
called (the Linux implementation always adds a timestamp on the Request,
so there is no loss in doing this).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recurring problem, in particular in the CCID code, is that RTT samples
from packets with timestamp echo and elapsed time options need to be taken.
This service is provided via a new function dccp_sample_rtt in this patch.
Furthermore, to protect against `insane' RTT samples, the sampled value
is bounded between 100 microseconds and 4 seconds - for which u32 is sufficient.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes two ambiguities in employing the new definition of before48,
following the analysis on http://www.mail-archive.com/dccp@vger.kernel.org/msg01295.html
(1) Updating GSR when P.seqno >= S.SWL
With the old definition we did not update when P.seqno and S.SWL are 2^47 apart. To
ensure the same behaviour as with the old definition, this is replaced with the
equivalent condition dccp_delta_seqno(S.SWL, P.seqno) >= 0
(2) Sending SYNC when P.seqno >= S.OSR
Here it is debatable whether the new definition causes an ambiguity: the case is
similar to (1); and to have consistency with the case (1), we use the equivalent
condition dccp_delta_seqno(S.OSR, P.seqno) >= 0
Detailed Justification
This reverts an earlier patch which disabled bidirectional mode, meaning that
a listening (passive) socket was not allowed to write to the other (active)
end of the connection.
This mode had been disabled when there were problems with CCID3, but it
imposes a constraint on socket programming and thus hinders deployment.
A change is included to ignore RX feedback received by the TX CCID3 module.
Many thanks to Andre Noll for pointing out this issue.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug caused by a previous patch, which causes DCCP servers in
LISTEN state to not receive packets.
This patch changes the logic so that
* servers in either LISTEN or OPEN state get the RX half connection packets
* clients in OPEN state get the TX half connection packets
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That accumulated over the last months hackaton, shame on me for not
using git-apply whitespace helping hand, will do that from now on.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This is an optimisation to reduce CPU load. The received feedback is now
only directed to the active CCID component, without requiring processing
also by the inactive one.
As a consequence, a similar test in ccid3.c is now redundant and is
also removed.
Justification:
Currently DCCP works as a unidirectional service, i.e. a listening server
is not at the same time a connecting client.
As far as I can see, several modifications are necessary until that
becomes possible.
At the present time, received feedback is both fed to the rx/tx CCID
modules. In unidirectional service, only one of these is active at any
one time.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This reaps the benefit of the earlier patch, which changed the type of
CCID 3 states to use enums, in that many conditions are now simplified
and the number of possible (unexpected) values is greatly reduced.
In a few instances, this also allowed to simplify pre-conditions; where
care has been taken to retain logical equivalence.
[DCCP]: Introduce a consistent BUG/WARN message scheme
This refines the existing set of DCCP messages so that
* BUG(), BUG_ON(), WARN_ON() have meaningful DCCP-specific counterparts
* DCCP_CRIT (for severe warnings) is not rate-limited
* DCCP_WARN() is introduced as rate-limited wrapper
Using these allows a faster and cleaner transition to their original
counterparts once the code has matured into a full DCCP implementation.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Sorts out the comments for processing steps 2,3 in section 8.5 of RFC 4340.
All comments have been updated against this document, and the reference to step
2 has been made consistent throughout the files.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Updates the references to spec documents throughout the code, taking into
account that
* the DCCP, CCID 2, and CCID 3 drafts all became RFCs in March this year
* RFC 1063 was obsoleted by RFC 1191
* draft-ietf-tcpimpl-pmtud-0x.txt was published as an Informational
RFC, RFC 2923 on 2000-09-22.
All references verified.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will later be included in struct dccp_request_sock so that we can
have per connection feature negotiation state while in the 3way
handshake, when we clone the DCCP_ROLE_LISTEN socket (in
dccp_create_openreq_child) we'll just copy this state from
dreq_minisock to dccps_minisock.
Also the feature negotiation and option parsing code will mostly touch
dccps_minisock, which will simplify some stuff.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming it to dccp_send_reset and moving it from the ipv4 specific
code to the core dccp code.
This fixes some bugs in IPV6 where timers would send v4 resets, etc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. No need for ->ccid_init nor ->ccid_exit, this is what module_{init,exit}
does and anynways neither ccid2 nor ccid3 were using it.
2. Rename struct ccid to struct ccid_operations and introduce struct ccid
with a pointer to ccid_operations and rigth after it the rx or tx
private state.
3. Remove the pointer to the state of the half connections from struct
dccp_sock, now its derived thru ccid_priv() from the ccid pointer.
Now we also can implement the setsockopt for changing the CCID easily as
no ccid init routines can affect struct dccp_sock in any way that prevents
other CCIDs from working if a CCID switch operation is asked by apps.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CCID should be notified of packet reception only when a packet is
valid. Therefore, the ACK vector needs to be processed before
notifying the CCID. Also, the CCID might need information provided by
the ACK vector.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ACK vectors are used, each packet with an ACK should contain an ACK
vector. The only exception currently is response packets. It
probably is not a good idea to store ACK vector state before the
connection is completed (to help protect from syn floods).
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
