* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (142 commits)
USB: fix race in autosuspend reschedule
atmel_usba_udc: Keep track of the device status
USB: Nikon D40X unusual_devs entry
USB: serial core should respect driver requirements
USB: documentation for USB power management
USB: skip autosuspended devices during system resume
USB: mutual exclusion for EHCI init and port resets
USB: allow usbstorage to have LUNS greater than 2Tb
USB: Adding support for SHARP WS011SH to ipaq.c
USB: add atmel_usba_udc driver
USB: ohci SSB bus glue
USB: ehci build fixes on au1xxx, ppc-soc
USB: add runtime frame_no quirk for big-endian OHCI
USB: funsoft: Fix termios
USB: visor: termios bits
USB: unusual_devs entry for Nikon DSC D2Xs
USB: re-remove <linux/usb_sl811.h>
USB: move <linux/usb_gadget.h> to <linux/usb/gadget.h>
USB: Export URB statistics for powertop
USB: serial gadget: Disable endpoints on unload
...
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Don't take semaphore in cpufreq_quick_get()
[CPUFREQ] Support different families in fid/did to frequency conversion
[CPUFREQ] cpufreq_stats: misc cpuinit section annotations
[CPUFREQ] implement !CONFIG_CPU_FREQ stub for cpufreq_unregister_notifier()
[CPUFREQ] mark hotplug notifier callback as __cpuinit
[CPUFREQ] Only check for transition latency on problematic governors (kconfig fix)
[CPUFREQ] allow ondemand and conservative cpufreq governors to be used as default
[CPUFREQ] move policy's governor initialisation out of low-level drivers into cpufreq core
[CPUFREQ] Longhaul - Add support for PM133 northbridge
[CPUFREQ] x86: use num_online_nodes to get physical cpus numbers for
Remove <linux/usb_sl811.h> ... somehow this was recreated when
the Blackfin arch was merged, instead of using <linux/usb/sl811.h>
which is the correct header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When compiling the Blackfin kernel, checksyscalls.pl will report lots of missing syscalls warnings.
This patch will add some missing syscalls which make sense on Blackfin arch
After appling this patch, toolchain should be rebuilt. Then recompiling the kernel with the new
toolchain.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Remove cruft - CONFIG_DEBUG_SERIAL_EARLY_INIT didn't work that well, and
DEBUG_KERNEL_START was just implmented poorly. Will replace with a new
checkin.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Fix a problem reported in the forums - libstdc++ can call writev with an
iovec containing { NULL, 0 }, which works fine on i686-linux, but fails on
Blackfin. Fixed by allowing size 0 transfers to/from userspace regardless
of the address.
Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Now that we have moved head.S into the init section, the load
address is not safe to point to as a workaround for ANOMALY 05000281
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
show_mem can not be marked as init, since it is called during
OOM condition from /mm/oom_kill.c:out_of_memory() and
/mm/page_alloc.c:__alloc_pages()
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- flush/inv the correct range
- dmacopy test failed when policy is write_back - invalidate before dma
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3367
It's the cache invalidate what is causing the issue.
There is no invalidate only instruction it's always: FLUSHINV
So when we "invalidate" after the DMA we might (do) overwrite freshly
dma'ed data by dirty Cache WB content.
Fixed by moving the "invalidate" at the beginning of dma_memcpy.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Comply with revised Anomaly Workarounds for BF533 05000311 and BF561 05000323
accoring to BF533 anomaly sheet Rev. A 09/04/07
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Print out debug info, as early as possible - even before the
kernel initializes the interrupt vectors. Now we can print out debug
messages almost anytime during the boot process.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Also ensure that the traps_c code doesn't cause a double fault, by
sending a signal to a faulting kernel before the memory subsystem
is fully initialized, by printing out the error message before sending
the signal.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Today when a double fault happens (exception during an exception
handling event), we go into an endless loop, with nothing comming out
the UART. With this patch, we actually see that we have commited a
double fault event
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
This allows debugging of problems which happen eary in the kernel
boot process (after bootargs are parsed, but before serial subsystem
is fully initialized)
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
