Added a new API function snd_ctl_activate_id() for activate / inactivate
the control element dynamically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently will ignore prefixes when creating DAPM controls. Since currently
all control creation goes through snd_soc_cnew() we can fix this by factoring
the prefixing into that function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
When multi component systems use DAIless amplifiers which require clocking
configuration it is at best hard to use the current clocking API as this
requires a DAI even though the device may not even have one. Address this
by adding set_sysclk() and set_pll() operations and APIs for CODECs.
In order to avoid issues with devices which could be used either with or
without DAIs make the DAI variants call through to their CODEC counterparts
if there is no DAI specific operation. Converting over entirely would create
problems for multi-DAI devices which offer per-DAI clocking setup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow a slight simplification of CODEC drivers by allowing DAPM routes and
widgets to be provided in a table. They will be instantiated at the end of
CODEC probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This is run after the DAPM widgets and routes are added, allowing setup
of things like jacks using the routes. The main card probe() is run before
anything else so can't be used for this purpose.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
These will be added after all devices are registered and allow most DAI
init functions in machine drivers to be replaced by simple data.
Regular controls are not supported as the registration function still
works in terms of CODECs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This means that rather than adding the board specific DAPM widgets to a
random CODEC DAPM context they can be added to the card itself which is
a bit cleaner. Previously there only was one DAPM context and it was
tied to the single supported CODEC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM9081 IRQ output can be either active high or active low and can
support either CMOS or open drain modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 has a different microphone bias architecture to WM8994 so needs
different configuration to WM8994. Support this in platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow direct routing of the WM8958 microphone detection signal to a GPIO
to be used, saving the need to demux the interrupt.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some systems wish to use jacks as wake sources. Provide a wake flag in the
GPIO configuration which causes the driver to enable the IRQ as a wake
source.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide driver data for cards within the card structure. To simplify the
implementation of the PM operations we don't use the struct device driver
data as this is used by the core to retrieve the card in callbacks from
the device model and PM core.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow hookup of cards registered directly with the core to the PM
operations by exporting the device power management operations to
modules, also exporting the default PM operations since it is
expected that most cards will end up using exactly the same setup.
Note that the callbacks require that the driver data for the card be
the snd_soc_card.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In order to support cards instantiated without using soc-audio remove
the use of the platform device in the card probe() and remove() ops.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The platform device for the card is tied closely to the soc-audio
implementation which we're currently trying to remove in favour of
allowing cards to have their own devices. Begin removing it by
replacing it with the card in the suspend and resume callbacks we
give to cards, also taking the opportunity to remove the legacy
suspend types which are currently hard coded anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Current format selection of FSI-codecs depended on platform information for FSI,
and chip default settings for codecs. It is not understandable/formal method.
This patch modify FSI and FSI-codecs to use snd_soc_dai_set_fmt.
But FSI can use I2S/PCM and SPDIF format today.
It can be selected to I2S/PCM by snd_soc_dai_set_fmt, but can not select SPDIF.
So, this patch change FSI platform information to have DAI/SPDIF mode.
If platform selects DAI mode (default),
FSI-codecs can select I2S/PCM by snd_soc_dai_set_fmt,
and if it is SPDIF mode, FSI become SPDIF format.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have zero users for PGA controls and the core support for them was
removed a while ago so no point in cut'n'pasting them into new macros,
even if it's too much hassle to update the existing ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
