This is an initial patch to do support for objects which needs physical
contiguous main ram, cursors and overlay registers on older chipsets.
These objects are bound on cursor bin, like pinning, and we copy
the data to/from the backing store object into the real one on attach/detach.
notes:
possible over the top in attach/detach operations.
no overlay support yet.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The detected fixed panel mode really is preferred, so mark it as such and
add it to the LVDS connector mode list.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
When mode setting is first initialized, the driver will call into
drm_helper_initial_config() to set up an initial output and framebuffer
configuration. This routine is responsible for probing the available
connectors, encoders, and crtcs, looking for modes and putting together
something reasonable (where reasonable is defined as "allows kernel
messages to be visible on as many displays as possible").
However, the code was a bit too aggressive in setting default modes when
none were found on a given connector. Even if some connectors had modes,
any connectors found lacking modes would have the default 800x600 mode added
to their mode list, which in some cases could cause problems later down the
line. In my case, the LVDS was perfectly available, but the initial config
code added 800x600 modes to both of the detected but unavailable HDMI
connectors (which are on my non-existent docking station). This ended up
preventing later code from setting a mode on my LVDS, which is bad.
This patch fixes that behavior by making the initial config code walk
through the connectors first, counting the available modes, before it decides
to add any default modes to a possibly connected output. It also fixes the
logic in drm_target_preferred() that was causing zeroed out modes to be set
as the preferred mode for a given connector, even if no modes were available.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
If we are running DRI1 userspace, we really need to set the sarea up properly.
thanks to Richard for finding/testing this.
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the absence of kernel mode setting, many drivers disable IRQs across VT
switch. The core DRM vblank code is missing a check for this case however;
even after IRQ disable, the vblank code will still have the vblank_enabled
flag set, so unless we track the fact that they're disabled at IRQ uninstall
time, when we VT switch back in we won't actually re-enable them, which means
any apps waiting on vblank before the switch will hang.
This patch does that and also adds a sanity check to the wait condition to
look for the irq_enabled flag in general, as well as adding a wakeup to the
IRQ uninstall path.
Fixes fdo bug #18879 with compiz hangs at VT switch.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In some cases userland may be confused and try to wait on vblank events from
pipes that aren't actually enabled. We shouldn't allow this, so return
-EINVAL if the pipe isn't on.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This is ported directly from the userland 2D driver code. The HDMI audio bits
aren't hooked up yet.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We also didn't track the cursor bo before and would leak a reference
when the cursor image was change.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This avoids a BUG_ON in the enter_vt path due to objects being in the GTT
when we shouldn't have ever let them be (as we're not supposed to touch the
device during that time).
This was triggered by a change in the 2D driver to use the GTT mapping of
objects after pinning them to improve software fallback performance.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Several subsystem open handlers dereference the fops_get() return value
without checking it for nullness. This opens a race condition between the
open handler and module unloading.
A module can be marked as being unloaded (MODULE_STATE_GOING) before its
exit function is called and gets the chance to unregister the driver.
During that window open handlers can still be called, and fops_get() will
fail in try_module_get() and return a NULL pointer.
This change checks the fops_get() return value and returns -ENODEV if NULL.
Reported-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
devname needs to be allocated before the irq is installed, so the
irq routines get the correct name in /proc.
Also check the return value from the AGP init function, and
fixup the exit points.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The error path for object list being null is in the second goto target.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This showed up in logs where people had a hung chip, so pinning was blocked
on the chip unpinning other buffers, and the X Server took its scheduler
signal during that time.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This removes the requirement for user space to pin a buffer before
setting a mode that is backed by the pixels from that buffer.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Fix this sparse warning:
drivers/gpu/drm/i915/intel_fb.c:417:5: warning: symbol 'intelfb_panic' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
