Impact: remove false positive warning
After a cpu was taken down during cpu hotplug (read: disabled for interrupts)
it still might have pending softirqs. However take_cpu_down makes sure
that the idle task will run next instead of ksoftirqd on the taken down cpu.
The idle task will call tick_nohz_stop_sched_tick which might warn about
pending softirqs just before the cpu kills itself completely.
However the pending softirqs on the dead cpu aren't a problem because they
will be moved to an online cpu during CPU_DEAD handling.
So make sure we warn only for online cpus.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix time warp bug
Alex Shi, along with Yanmin Zhang have been noticing occasional time
inconsistencies recently. Through their great diagnosis, they found that
the xtime_nsec value used in update_wall_time was occasionally going
negative. After looking through the code for awhile, I realized we have
the possibility for an underflow when three conditions are met in
update_wall_time():
1) We have accumulated a second's worth of nanoseconds, so we
incremented xtime.tv_sec and appropriately decrement xtime_nsec.
(This doesn't cause xtime_nsec to go negative, but it can cause it
to be small).
2) The remaining offset value is large, but just slightly less then
cycle_interval.
3) clocksource_adjust() is speeding up the clock, causing a
corrective amount (compensating for the increase in the multiplier
being multiplied against the unaccumulated offset value) to be
subtracted from xtime_nsec.
This can cause xtime_nsec to underflow.
Unfortunately, since we notify the NTP subsystem via second_overflow()
whenever we accumulate a full second, and this effects the error
accumulation that has already occured, we cannot simply revert the
accumulated second from xtime nor move the second accumulation to after
the clocksource_adjust call without a change in behavior.
This leaves us with (at least) two options:
1) Simply return from clocksource_adjust() without making a change if we
notice the adjustment would cause xtime_nsec to go negative.
This would work, but I'm concerned that if a large adjustment was needed
(due to the error being large), it may be possible to get stuck with an
ever increasing error that becomes too large to correct (since it may
always force xtime_nsec negative). This may just be paranoia on my part.
2) Catch xtime_nsec if it is negative, then add back the amount its
negative to both xtime_nsec and the error.
This second method is consistent with how we've handled earlier rounding
issues, and also has the benefit that the error being added is always in
the oposite direction also always equal or smaller then the correction
being applied. So the risk of a corner case where things get out of
control is lessened.
This patch fixes bug 11970, as tested by Yanmin Zhang
http://bugzilla.kernel.org/show_bug.cgi?id=11970
Reported-by: alex.shi@intel.com
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Acked-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Tested-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, move all hrtimer processing into hardirq context
This is an attempt at removing some of the hrtimer complexity by
reducing the number of callback modes to 1.
This means that all hrtimer callback functions will be ran from HARD-irq
context.
I went through all the 30 odd hrtimer callback functions in the kernel
and saw only one that I'm not quite sure of, which is the one in
net/can/bcm.c - hence I'm CC-ing the folks responsible for that code.
Furthermore, the hrtimer core now calls callbacks directly with IRQs
disabled in case you try to enqueue an expired timer. If this timer is a
periodic timer (which should use hrtimer_forward() to advance its time)
then it might be possible to end up in an inf. recursive loop due to the
fact that hrtimer_forward() doesn't round up to the next timer
granularity, and therefore keeps on calling the callback - obviously
this needs a fix.
Aside from that, this seems to compile and actually boot on my dual core
test box - although I'm sure there are some bugs in, me not hitting any
makes me certain :-)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: (future) size reduction for large NR_CPUS.
Dynamically allocating cpumasks (when CONFIG_CPUMASK_OFFSTACK) saves
space for small nr_cpu_ids but big CONFIG_NR_CPUS. cpumask_var_t
is just a struct cpumask for !CONFIG_CPUMASK_OFFSTACK.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: nohz powersavings and wakeup regression
commit fb02fbc14d (NOHZ: restart tick
device from irq_enter()) causes a serious wakeup regression.
While the patch is correct it does not take into account that spurious
wakeups happen on x86. A fix for this issue is available, but we just
revert to the .27 behaviour and let long running softirqs screw
themself.
Disable it for now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit fb02fbc14d (NOHZ: restart tick
device from irq_enter())
solves the problem of stale jiffies when long running softirqs happen
in a long idle sleep period, but it has a major thinko in it:
When the interrupt which came in _is_ the timer interrupt which should
expire ts->sched_timer then we cancel and rearm the timer _before_ it
gets expired in hrtimer_interrupt() to the next period. That means the
call back function is not called. This game can go on for ever :(
Prevent this by making sure to only rearm the timer when the expiry
time is more than one tick_period away. Otherwise keep it running as
it is either already expired or will expiry at the right point to
update jiffies.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Venkatesch Pallipadi <venkatesh.pallipadi@intel.com>
The base address of a (per cpu) clock base is a useful debug info.
Add it and bump the version number of timer_lists.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The per cpu clock events device output of timer_list lacks an
association of the device to the cpu which is annoying when looking at
the output of /proc/timer_list from a 128 way system.
Add the CPU number info and mark the broadcast device in the device
list printout.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current timer_list output prints the address of the on stack copy
of the active hrtimer instead of the hrtimer itself.
Print the address of the real timer instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We did not restart the tick device from irq_enter() to avoid double
reprogramming and extra events in the return immediate to idle case.
But long lasting softirqs can lead to a situation where jiffies become
stale:
idle()
tick stopped (reprogrammed to next pending timer)
halt()
interrupt
jiffies updated from irq_enter()
interrupt handler
softirq function 1 runs 20ms
softirq function 2 arms a 10ms timer with a stale jiffies value
jiffies updated from irq_exit()
timer wheel has now an already expired timer
(the one added in function 2)
timer fires and timer softirq runs
This was discovered when debugging a timer problem which happend only
when the ath5k driver is active. The debugging proved that there is a
softirq function running for more than 20ms, which is a bug by itself.
To solve this we restart the tick timer right from irq_enter(), but do
not go through the other functions which are necessary to return from
idle when need_resched() is set.
Reported-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Elias Oltmanns <eo@nebensachen.de>
We have two separate nohz function calls in irq_enter() for no good
reason. Just call a single NOHZ function from irq_enter() and call
the bits in the tick code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
export get_cpu_idle_time_us() for it to be used in ondemand governor.
Last update time can be current time when the CPU is currently non-idle,
accounting for the busy time since last idle.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Impact: jiffies increment too fast.
Hugh Dickins noted that with NOHZ=n and HIGHRES=n jiffies get
incremented too fast. The reason is a wrong check in the broadcast
enter/exit code, which keeps the local apic timer in periodic mode
when the switch happens.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: per CPU hrtimers can be migrated from a dead CPU
The hrtimer code has no knowledge about per CPU timers, but we need to
prevent the migration of such timers and warn when such a timer is
active at migration time.
Explicitely mark the timers as per CPU and use a more understandable
mode descriptor for the interrupts safe unlocked callback mode, which
is used by hrtimer_sleeper and the scheduler code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change PPM_SCALE_INV_SHIFT so that it doesn't throw away any input bits
(19 is the amount of the factor 2 in PPM_SCALE), the output frequency
can then be calculated back to its input value, as the inverse divide
produce a slightly larger value, which is then correctly rounded by the
final shift.
Reported-by: Martin Ziegler <ziegler@uni-freiburg.de>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Due to a rounding problem during a clock update it's possible for readers
to observe the clock jumping back by 1nsec. The following simplified
example demonstrates the problem:
cycle xtime
0 0
1000 999999.6
2000 1999999.2
3000 2999998.8
...
1500 = 1499999.4
= 0.0 + 1499999.4
= 999999.6 + 499999.8
When reading the clock only the full nanosecond part is used, while
timekeeping internally keeps nanosecond fractions. If the clock is now
updated at cycle 1500 here, a nanosecond is missing due to the truncation.
The simple fix is to round up the xtime value during the update, this also
changes the distance to the reference time, but the adjustment will
automatically take care that it stays under control.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is a change that makes the 11-minute RTC update be run in the process
context. This is so that update_persistent_clock() can sleep, which may
be required for certain types of RTC hardware -- most notably I2C devices.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
