Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
genirq requires that the IRQ requests that do not provided a handler to
use the IRQF_ONESHOT flag. This is to prevent situations in which the irq line
is reenabled while the interrupt is still asserted. While this situation may
not happen in edge type interrupts, genirq still requires to use IRQF_ONESHOT.
Also, remove the IRQF_DISABLED as the flag is now a NOOP and has been
deprecated.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The VENC interfaces uses it's venc_set_timing() function to take in a new set
of timings. If the panel is disabled, it does not disable and re-enable the
interface. Currently, the manager timings are applied in venc_power_on(), these
are not called by set_timings if the panel is disabled. When checking overlay
and manager data, the DSS driver uses the last applied manager timings, and not
the timings held by omap_dss_device struct. Hence, there is a need to apply the
new manager timings even if the panel is disabled.
Apply the manager timings if the VENC panel is disabled.
This is similar to the commit below which fixed the same issue for HDMI/DPI
interfaces:
fcc3661990
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS2 driver uses the timings in manager's private data to check the validity of
overlay and manager infos written by the user. For VENC interface, we divide the
Y resolution by half when writing to the DISPC_DIGIT_SIZE register as the
content is interlaced. However, the height of the manager/display with respect
to the content shown through VENC still remains the same.
The VENC driver divides the y_res parameter in omap_video_timings by half, and
then applies the configuration. This leads to manager's private data storing
the wrong Y resolution. Hence, overlay related checks fail.
Ensure that manager's private data stores the original timings, and the Y
resolution is halved only when we write to the DISPC register. This is a hack,
the proper solution would be to pass some sort of interlace parameter which
makes the call whether we should divide y_res or not.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
TILER is a block in OMAP4's DMM which lets DSS fetch frames in a rotated manner.
Physical memory can be mapped to a portion of OMAP's system address space called
TILER address space. The TILER address space is split into 8 views. Each view
represents a rotated or mirrored form of the mapped physical memory. When a
DISPC overlay's base address is programmed to one of these views, the TILER
fetches the pixels according to the orientation of the view. A view is further
split into 4 containers, each container holds elements of a particular size.
Rotation can be achieved at the granularity of elements in the container. For
more information on TILER, refer to the Memory Subsytem section in OMAP4 TRM.
Rotation type TILER has been added which is used to exploit the capabilities of
these 8 views for performing various rotations.
When fetching from addresses mapped to TILER space, the DISPC DMA can fetch
pixels in either 1D or 2D bursts. The fetch depends on which TILER container we
are accessing. Accessing 8, 16 and 32 bit sized containers requires 2D bursts,
and page mode sized containers require 1D bursts.
The DSS2 user is expected to provide the Tiler address of the view that it is
interested in. This is passed to the paddr and p_uv_addr parameters in
omap_overlay_info. It is also expected to provide the stride value based on the
view's orientation and container type, this should be passed to the screen_width
parameter of omap_overlay_info. In calc_tiler_rotation_offset screen_width is
used to calculate the required row_inc for DISPC. x_predecim and y_predecim are
also used to calculate row_inc and pix_inc thereby adding predecimation support
for TILER.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many
places in code expect the execution to stop, and this causes compiler
warnings about uninitialized variables and returning from a non-void
function without a return value.
This patch fixes the warnings by initializing the variables and
returning properly after BUG() lines. However, the behaviour is still
undefined after the BUG, but this is the choice the user makes when
using CONFIG_BUG=n.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many
places in code expect the execution to stop, and this causes compiler
warnings about uninitialized variables and returning from a non-void
function without a return value.
This patch fixes the warnings by initializing the variables and
returning properly after BUG() lines. However, the behaviour is still
undefined after the BUG, but this is the choice the user makes when
using CONFIG_BUG=n.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many
places in code expect the execution to stop, and this causes compiler
warnings about uninitialized variables and returning from a non-void
function without a return value.
This patch fixes the warnings by initializing the variables and
returning properly after BUG() lines. However, the behaviour is still
undefined after the BUG, but this is the choice the user makes when
using CONFIG_BUG=n.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 05dd0f5308 ("OMAPDSS: DISPC: Update
Accumulator configuration for chroma plane") adds
dispc_ovl_set_accu_uv() function that sets the accu, but the function
only handles YUV and NV12 modes, and BUGs otherwise.
The patch also adds a call to the function, but unfortunately the place
of call was such that the mode could be other than YUV or NV12, thus
crashing the driver.
This patchs moves the call to a slightly later spot, at which point only
YUV and NV12 modes are handled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Chandrabhanu Mahapatra <cmahapatra@ti.com>
There is a problem related to DSS FIFO thresholds and power management
on OMAP3. It seems that when the full PM hits in, we get underflows. The
core reason is unknown, but after experiments it looks like only
particular FIFO thresholds work correctly.
This bug is related to an earlier patch, which added special FIFO
threshold configuration for OMAP3, because DSI command mode output
didn't work with the normal threshold configuration.
However, as the above work-around worked fine for other output types
also, we currently always configure thresholds in this special way on
OMAP3. In theory there should be negligible difference with this special
way and the standard way. The first paragraph explains what happens in
practice.
This patch changes the driver to use the special threshold configuration
only when the output is a manual update display on OMAP3. This does
include RFBI displays also, and although it hasn't been tested (no
boards using RFBI) I suspect the similar behaviour is present there
also, as the DISPC side should work similarly for DSI command mode and
RFBI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Joe Woodward <jw@terrafix.co.uk>
DSI supports interleaving of command mode packets during the HSA, HFP, HBP and
BLLP blanking intervals in a video mode stream. This is useful as a user may
want to read or change the configuration of a panel without stopping the video
stream.
On OMAP DSI, we can queue HS or LP command mode packets in the TX FIFO, and
the DSI HW takes care of interleaving this data during the one of the blanking
intervals. The DSI HW needs to be programmed with the maximum amount of data
that can be interleaved in a particular blanking period. A blanking period
cannot be used to send command mode data for it's complete duration, there is
some amount of time required for the DSI data and clock lanes to transition
to the desired LP or HS state.
Based on the state of the lanes at the beginning and end of the blanking period,
we have different scenarios, with each scenario having a different value of time
required to transition to HS or LP. Refer to the section 'Interleaving Mode' in
OMAP TRM for more info on the scenarios and the equations to calculate the time
required for HS or LP transitions.
We use the scenarios which takes the maximum time for HS or LP transition, this
gives us the minimum amount of time that can be used to interleave command mode
data. The amount of data that can be sent during this minimum time is calculated
for command mode packets both in LP and HS. These are written to the registers
DSI_VM_TIMING4 to DSI_VM_TIMING6.
The calculations don't take into account the time required of transmitting BTA
when doing a DSI read, or verifying if a DSI write went through correctly. Until
these latencies aren't considered, the behaviour of DSI is unpredictable when
a BTA is interleaved during a blanking period. Enhancement of these calculations
is a TODO item.
The calculations are derived from DSI parameter calculation tools written by
Sebastien Fagard <s-fagard@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC has two accumulator registers DISPC_VIDp_ACCU_0 and DISPC_VIDp_ACCU_1 each
with horizontal and vertical bit fields. The bit fields can take values in the
range of -1024 to 1023. Based on bit field values DISPC decides on which one out
of 8 phases the filtering starts. DISPC_VIDp_ACCU_0 is used for progressive
output and for interlaced output both DISPC_VIDp_ACCU_0 and DISPC_VIDp_ACCU_1
are used.
The current accumulator values in DISPC scaling logic for chroma plane takes
default values for all color modes and rotation types. So, the horizontal and
vertical up and downsampling accumulator bit field values have been updated for
better performance.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implement the DSS device driver audio support interface in the HDMI
panel driver and generic driver. The implementation relies on the
IP-specific functions that are defined at DSS probe time.
A mixed locking strategy is used. The panel's mutex is used when
the state of the panel is queried as required by the audio functions.
The audio state is protected using a spinlock as users of DSS HDMI
audio functionality might start/stop audio while holding a spinlock.
The mutex and the spinlock are held and released as needed by each
individual function to protect the panel state and the audio state.
Although the panel's audio_start functions does not check whether
the panel is active, the audio _ENABLED state can be reached only
from audio_enable, which does check the state of the panel. Also,
if the panel is ever disabled, the audio state will transition
to _DISABLED. Transitions are always protected by the audio lock.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
As the hdmi_lock mutex is inside the hdmi struct, rename to simply
"lock". This is only a change in the name. There are not changes
in functionality.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
As of today, the only know user of the DSS HDMI audio support is
ASoC. Hence, it makes sense to remap the speaker order to match
the ALSA speaker order. In the future, a dynamic mapping mechanism
may be implemented.
Remapping is needed as the HDMI speaker order is FL/FR/LFE/C/RL/RR/
RLC-FLC/RRC-FLC while the ALSA order is FL/FR/RL/RR/C/LFE/SL/SR.
Refer to CEA-861 Section 6.6.2 for further details.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
The generic HDMI driver does not need to know about the specific
settings of a given IP. Hence, it just passes the audio configuration
and the IP library parses such configuration and sets the IP
accordingly. This patch introduces an IP-specific audio configuration
function.
Also, this patch implements the audio config function for OMAP4. The
DMA, format and core config functions are no longer exposed to the
generic HDMI driver as they are IP-specific.
The audio configuration function caters for 16-bit through 24-bit
audio samples with sample rates from 32kHz and up to 192kHz as well
as up to 8 audio channels.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Add support for more sample rates when calculating N and CTS. This
covers all the audio sample rates that an HDMI source is allowed
to transmit according to the HDMI 1.4a specification.
Also, reorganize the logic for the calculation when using deep color.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
The N and CTS parameters are relevant to all HDMI implementations and
not specific to a given IP. Hence, the calculation is relocated
into the generic HDMI driver.
Also, deep color is not queried but it is still considered in the
calculation of N. This is to be changed when deep color functionality is
implemented in the driver.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Utilize a snd_aes_iec958 struct to write the parameters of the IEC-60958
channel status word into the HDMI IP registers. Hence, the user of the
driver has full control of what parameters are written in the word.
Also, some of the parameters of the I2S structure have been removed
as they are actually IEC-60958 parameters.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Instead of having OMAPDSS HDMI audio functionality depending on the
ASoC HDMI audio driver, use a new config option so that
potential users, including ASoC, may select if needed.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Decouple the enable/disable operation of the HDMI audio wrapper from
audio start/stop. Otherwise, an audio FIFO underflow may occur. The
audio wrapper enablement must be done after configuration and
before audio playback is started.
Signed-off-by: Axel Castaneda Gonzalez <x0055901@ti.com>
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
According to the most up-to-date documentation from Texas Instruments,
the configuration of High Bitrate Audio is not possible. Also, it is
not possible to set polarity of the I2S Word Select signal. This patch
removes the invalid settings.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Instead of having its own definitions for CEA-861 and IEC-60958, the HDMI
driver should use those provided by ALSA. This patch removes the definitions
that are already provided by ALSA.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Remove the ASoC OMAP HDMI audio codec. The goal of removing the codec
is to, in subsequent patches, give way to the implementation of the HDMI
audio support using the DSS device driver audio interface. This
approach will expose the HDMI audio functionality to any interested entity.
In a separate patch, ASoC will use this new approach to expose HDMI audio
to ALSA.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
