There are several places where the USB core needs to disable USB 3.0
Link PM:
- usb_bind_interface
- usb_unbind_interface
- usb_driver_claim_interface
- usb_port_suspend/usb_port_resume
- usb_reset_and_verify_device
- usb_set_interface
- usb_reset_configuration
- usb_set_configuration
Use the new LPM disable/enable functions to temporarily disable LPM
around these critical sections.
We need to protect the critical section around binding and unbinding USB
interface drivers. USB drivers may want to disable hub-initiated USB
3.0 LPM, which will change the value of the U1/U2 timeouts that the xHCI
driver will install. We need to disable LPM completely until the driver
is bound to the interface, and the driver has a chance to enable
whatever alternate interface setting it needs in its probe routine.
Then re-enable USB3 LPM, and recalculate the U1/U2 timeout values.
We also need to disable LPM in usb_driver_claim_interface,
because drivers like usbfs can bind to an interface through that
function. Note, there is no way currently for userspace drivers to
disable hub-initiated USB 3.0 LPM. Revisit this later.
When a driver is unbound, the U1/U2 timeouts may change because we are
unbinding the last driver that needed hub-initiated USB 3.0 LPM to be
disabled.
USB LPM must be disabled when a USB device is going to be suspended.
The USB 3.0 spec does not define a state transition from U1 or U2 into
U3, so we need to bring the device into U0 by disabling LPM before we
can place it into U3. Therefore, call usb_unlocked_disable_lpm() in
usb_port_suspend(), and call usb_unlocked_enable_lpm() in
usb_port_resume(). If the port suspend fails, make sure to re-enable
LPM by calling usb_unlocked_enable_lpm(), since usb_port_resume() will
not be called on a failed port suspend.
USB 3.0 devices lose their USB 3.0 LPM settings (including whether USB
device-initiated LPM is enabled) across device suspend. Therefore,
disable LPM before the device will be reset in
usb_reset_and_verify_device(), and re-enable LPM after the reset is
complete and the configuration/alt settings are re-installed.
The calculated U1/U2 timeout values are heavily dependent on what USB
device endpoints are currently enabled. When any of the enabled
endpoints on the device might change, due to a new configuration, or new
alternate interface setting, we need to first disable USB 3.0 LPM, add
or delete endpoints from the xHCI schedule, install the new interfaces
and alt settings, and then re-enable LPM. Do this in usb_set_interface,
usb_reset_configuration, and usb_set_configuration.
Basically, there is a call to disable and then enable LPM in all
functions that lock the bandwidth_mutex. One exception is
usb_disable_device, because the device is disconnecting or otherwise
going away, and we should not care about whether USB 3.0 LPM is enabled.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Keep the usb-serial support for dynamic IDs in sync with the usb
support. This enables readout of dynamic device IDs for
usb-serial drivers. Common code is exported from the usb core
system and reused by the usb-serial bus driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This enables the current list of dynamic IDs to be read out through
either new_id or remove_id.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This option has been deprecated for many years now, and no userspace
tools use it anymore, so it should be safe to finally remove it.
Reported-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1532) fixes a mistake in the USB suspend code. When the
system is going to sleep, we should ignore errors in powering down USB
devices, because they don't really matter. The devices will go to low
power anyway when the entire USB bus gets suspended (except for
SuperSpeed devices; maybe they will need special treatment later).
However we should not ignore errors in suspending root hubs,
especially if the error indicates that the suspend raced with a wakeup
request. Doing so might leave the bus powered on while the system was
supposed to be asleep, or it might cause the suspend of the root hub's
parent controller device to fail, or it might cause a wakeup request
to be ignored.
The patch fixes the problem by ignoring errors only when the device in
question is not a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chen Peter <B29397@freescale.com>
CC: <stable@vger.kernel.org>
Tested-by: Chen Peter <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB merge for 3.4-rc1 from Greg KH:
"Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and
other various minor things.
There are some patches touching arch code, but they have all been
acked by the various arch maintainers."
* tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (302 commits)
net: qmi_wwan: add support for ZTE MF820D
USB: option: add ZTE MF820D
usb: gadget: f_fs: Remove lock is held before freeing checks
USB: option: make interface blacklist work again
usb/ub: deprecate & schedule for removal the "Low Performance USB Block" driver
USB: ohci-pxa27x: add clk_prepare/clk_unprepare calls
USB: use generic platform driver on ath79
USB: EHCI: Add a generic platform device driver
USB: OHCI: Add a generic platform device driver
USB: ftdi_sio: new PID: LUMEL PD12
USB: ftdi_sio: add support for FT-X series devices
USB: serial: mos7840: Fixed MCS7820 device attach problem
usb: Don't make USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.
usb gadget: fix a section mismatch when compiling g_ffs with CONFIG_USB_FUNCTIONFS_ETH
USB: ohci-nxp: Remove i2c_write(), use smbus
USB: ohci-nxp: Support for LPC32xx
USB: ohci-nxp: Rename symbols from pnx4008 to nxp
USB: OHCI-HCD: Rename ohci-pnx4008 to ohci-nxp
usb: gadget: Kconfig: fix typo for 'different'
usb: dwc3: pci: fix another failure path in dwc3_pci_probe()
...
This patch (as1514) cleans up some places where new_id and remove_id
sysfs attributes are created and deleted. Handling both attributes in
a single routine rather than a pair of routines makes the code
smaller. It also prevents certain kinds of errors, like one we
currently have in the USB subsystem: The removeid attribute is often
created even when newid isn't (because the driver's no_dynamid_id flag
is set).
In the case of the PCMCIA subsystem, the newid attribute is created
but never explicitly deleted. The patch adds a deletion routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As part of the removal of get_driver()/put_driver(), this patch
(as1511) changes all the places that add dynamic IDs for drivers.
Since these additions are done by writing to the drivers' sysfs
attribute files, and the attributes are removed when the drivers are
unregistered, there is no reason to take an extra reference to the
drivers.
The one exception is the pci-stub driver, which calls pci_add_dynid()
as part of its registration. But again, there's no reason to take an
extra reference here, because the driver can't be unloaded while it is
being registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This eliminates the last instance of a function's behavior
controlled by a parameter as Linus hates such things.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a driver does not support the suspend/resume callbacks
it will be forcibly disconnected. There is no reason to check
for support of the callbacks after that.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When adding the ID of a composite device dynamically to a driver, all
hitherto unbound interfaces are bound to this driver regardless of their
class, which may not be intended.
The patch adds the option to tell the targeted interface class to a driver
via the "new_id" attribute, in addition to the device ID.
Also, it appends the ABI documentation accordingly.
Example:
$ echo "1234 2a2a ff" >/sys/bus/usb-serial/drivers/option1/new_id
will bind only vendor-specific interfaces to the 3G driver.
Signed-off-by: Josua Dietze <digidietze@draisberghof.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit
f71648d73c (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. A companion
patch changes the PM core's behavior, but we also need to change the
USB core. In particular, this patch (as1493) updates the device's
last_busy time when an autosuspend fails, so that the PM core will
retry the autosuspend in the future when the delay time expires
again.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Use the lightweight version of the header that has just THIS_MODULE
and EXPORT_SYMBOL variants.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.
If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A return value of -EINPROGRESS from pm_runtime_get indicates that
the device is already resuming due to a previous call. Internally,
usb_autopm_get_interface_async doesn't treat this as an error and
increments the usage count, but passes the error status along
to the caller. The logical assumption of the caller is that
any negative return value reflects the device not resuming
and the pm_usage_cnt not being incremented. Since the usage count
is being incremented and the device is resuming, return success (0)
instead.
Signed-off-by: James Wylder <james.wylder@motorola.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1482) adds a macro for testing whether or not a
pm_message value represents an autosuspend or autoresume (i.e., a
runtime PM) event. Encapsulating this notion seems preferable to
open-coding the test all over the place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
MAINTAINERS: add myself as maintainer of USB/IP
usb: r8a66597-hcd: fix cannot detect low/full speed device
USB: ehci-ath79: fix a NULL pointer dereference
USB: Add new FT232H chip to drivers/usb/serial/ftdi_sio.c
usb/isp1760: Fix bug preventing the unlinking of control urbs
USB: Fix up URB error codes to reflect implementation.
xhci: Always set urb->status to zero for isoc endpoints.
xhci: Add reset on resume quirk for asrock p67 host
xHCI 1.0: Incompatible Device Error
USB: don't let errors prevent system sleep
USB: don't let the hub driver prevent system sleep
USB: change maintainership of ohci-hcd and ehci-hcd
xHCI 1.0: Force Stopped Event(FSE)
xhci: Don't warn about zeroed bMaxBurst descriptor field.
USB: Free bandwidth when usb_disable_device is called.
xhci: Reject double add of active endpoints.
USB: TI 3410/5052 USB Serial Driver: Fix mem leak when firmware is too big.
usb: musb: gadget: clear TXPKTRDY flag when set FLUSHFIFO
usb: musb: host: compare status for negative error values
This patch (as1473) renames the "in_suspend" field in struct
dev_pm_info to "is_prepared", in preparation for an upcoming change.
The new name is more descriptive of what the field really means.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
This patch (as1464) implements the recommended policy that most errors
during suspend or hibernation should not prevent the system from going
to sleep. In particular, failure to suspend a USB driver or a USB
device should not prevent the sleep from succeeding:
Failure to suspend a device won't matter, because the device will
automatically go into suspend mode when the USB bus stops carrying
packets. (This might be less true for USB-3.0 devices, but let's not
worry about them now.)
Failure of a driver to suspend might lead to trouble later on when the
system wakes up, but it isn't sufficient reason to prevent the system
from going to sleep.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB defines usb_device_type pointing to usb_device_pm_ops that
provides system-wide PM callbacks only and usb_bus_type pointing to
usb_bus_pm_ops that provides runtime PM callbacks only. However,
the USB runtime PM callbacks may be defined in usb_device_pm_ops
which makes it possible to drop usb_bus_pm_ops and will allow us
to consolidate the handling of subsystems by the PM core code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
The PM core reacts badly when the return code from usb_runtime_suspend()
is not 0, -EAGAIN, or -EBUSY. The PM core regards this as a fatal error,
and refuses to run anymore PM helper functions. In particular,
usbfs_open() and other usbfs functions will fail because the PM core will
return an error code when usb_autoresume_device() is called. This causes
libusb and/or lsusb to either hang or segfault.
If a USB device cannot suspend for some reason (e.g. a hub doesn't report
it has remote wakeup capabilities), we still want lsusb and other
userspace programs to work. So return -EBUSY, which will fill people's
log files with failed tries, but will ensure userspace still works.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
spi / PM: Support dev_pm_ops
PM: Prototype the pm_generic_ operations
PM / Runtime: Generic resume shouldn't set RPM_ACTIVE unconditionally
PM: Use dev_name() in core device suspend and resume routines
PM: Permit registration of parentless devices during system suspend
PM: Replace the device power.status field with a bit field
PM: Remove redundant checks from core device resume routines
PM: Use a different list of devices for each stage of device suspend
PM: Avoid compiler warning in pm_noirq_op()
PM: Use pm_wakeup_pending() in __device_suspend()
PM / Wakeup: Replace pm_check_wakeup_events() with pm_wakeup_pending()
PM: Prevent dpm_prepare() from returning errors unnecessarily
PM: Fix references to basic-pm-debugging.txt in drivers-testing.txt
PM / Runtime: Add synchronous runtime interface for interrupt handlers (v3)
PM / Hibernate: When failed, in_suspend should be reset
PM / Hibernate: hibernation_ops->leave should be checked too
Freezer: Fix a race during freezing of TASK_STOPPED tasks
PM: Use proper ccflag flag in kernel/power/Makefile
PM / Runtime: Fix comments to match runtime callback code
