commit c21eebb503
"wl12xx: add RX filters ACX commands" breaks the build
when CONFIG_PM isn't defined:
ERROR: "wl1271_rx_filter_get_fields_size"
[drivers/net/wireless/ti/wlcore/wlcore.ko] undefined!
ERROR: "wl1271_rx_filter_flatten_fields"
[drivers/net/wireless/ti/wlcore/wlcore.ko] undefined!
code in drivers/net/wireless/ti/wlcore/acx.c is using these
functions unconditionally while they are #ifdefed CONFIG_PM.
Fix it by ifdefing all relevant RX filters code with CONFIG_PM.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR933x, the internal regulator settings need to be applied before the
PLL init to avoid stability issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"> Can you provide more information about the issues with high power devices?
Tx being flakey and Rx not working at all."
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tx_setup_buffer() can fail if there is no ath_buf left, or if mapping DMA
failed. In this case it frees the skb passed to it.
If ath_tx_setup_buffer is called from ath_tx_form_aggr, the skb is still
linked into the tid buffer list and must be dequeued before being released.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has been found that active Rx can interfere with stopping tx DMA, which
could result in at least parts of those "Failed to stop Tx DMA!" messages.
Stopping rx before tx should prevent that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware is more than 300KB big and you should not use kmalloc for
such big allocations. This allocation with kmalloc failed on my mips
based device (BCM47186).
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver disables interrupt just after requesting it and enables it
later, after interface is up. However currently there is a time window
between request_irq() and disable_irq() where if interrupt arrives, the
driver oopses because it's not yet ready to process it. This can be
reproduced by inserting the module, associating and removing the module
multiple times.
Eliminate this race by setting IRQF_NOAUTOEN flag before request_irq().
Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a station fails in
iwl_restore_stations, the driver treats it
like a successful station add and sends a
link quality command, when it it shouldn't.
This patch fixes one of the potential
sources for kernel warnings like this one:
WARNING: at drivers/net/wireless/iwlwifi/iwl-agn-sta.c:905 iwl_send_lq_cmd+0x130/0x217 [iwlwifi]()
Hardware name: 3323A2G
Modules linked in: ...
Pid: 17359, comm: kworker/u:2 Tainted: G O 3.3.0-wl+ #1
Call Trace:
[<ffffffff81039620>] warn_slowpath_common+0x7e/0x96
[<ffffffff8103964d>] warn_slowpath_null+0x15/0x17
[<ffffffffa02a9f0b>] iwl_send_lq_cmd+0x130/0x217 [iwlwifi]
[<ffffffffa02aa1fb>] iwl_restore_stations+0x209/0x289 [iwlwifi]
[<ffffffffa02b07c2>] iwlagn_commit_rxon+0x602/0x7bd [iwlwifi]
[<ffffffffa02b111f>] iwlagn_bss_info_changed+0x247/0x31a [iwlwifi]
[<ffffffffa0861437>] ieee80211_bss_info_change_notify+0x1a5/0x1ba [mac80211]
[<ffffffffa088afad>] ieee80211_destroy_auth_data+0x4b/0x70 [mac80211]
[<ffffffffa088df26>] ieee80211_sta_work+0xb5/0x954 [mac80211]
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ucode16 option is still very much work in
progress, so there's no need to ask any users
about it. Remove the option and code for now,
we'll put it back when it's actually working.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shadow registers in the device are meant to
allow the driver to update certain device
registers without needing to wake up all
components of the device. However, using
this feature in the device causes
communication between the driver and the
device to become unreliable, resulting in
host command timeouts.
Disable this feature by default till a fix is
available for the bug.
Cc: stable@vger.kernel.org #2.6.38+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The logic that allows to have a short TFD queue was completely wrong.
We do maintain 256 Transmit Frame Descriptors, but they point to
recycled buffers. We used to attach and de-attach different TFDs for
the same buffer and it worked since they pointed to the same buffer.
Also zero the number of BDs after unmapping a TFD. This seems not
necessary since we don't reclaim the same TFD twice, but I like
housekeeping.
This patch solves this warning:
[ 6427.079855] WARNING: at lib/dma-debug.c:866 check_unmap+0x727/0x7a0()
[ 6427.079859] Hardware name: Latitude E6410
[ 6427.079865] iwlwifi 0000:02:00.0: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x00000000296d393c] [size=8 bytes]
[ 6427.079870] Modules linked in: ...
[ 6427.079950] Pid: 6613, comm: ifconfig Tainted: G O 3.3.3 #5
[ 6427.079954] Call Trace:
[ 6427.079963] [<c10337a2>] warn_slowpath_common+0x72/0xa0
[ 6427.079982] [<c1033873>] warn_slowpath_fmt+0x33/0x40
[ 6427.079988] [<c12dcb77>] check_unmap+0x727/0x7a0
[ 6427.079995] [<c12dcdaa>] debug_dma_unmap_page+0x5a/0x80
[ 6427.080024] [<fe2312ac>] iwlagn_unmap_tfd+0x12c/0x180 [iwlwifi]
[ 6427.080048] [<fe231349>] iwlagn_txq_free_tfd+0x49/0xb0 [iwlwifi]
[ 6427.080071] [<fe228e37>] iwl_tx_queue_unmap+0x67/0x90 [iwlwifi]
[ 6427.080095] [<fe22d221>] iwl_trans_pcie_stop_device+0x341/0x7b0 [iwlwifi]
[ 6427.080113] [<fe204b0e>] iwl_down+0x17e/0x260 [iwlwifi]
[ 6427.080132] [<fe20efec>] iwlagn_mac_stop+0x6c/0xf0 [iwlwifi]
[ 6427.080168] [<fd8480ce>] ieee80211_stop_device+0x5e/0x190 [mac80211]
[ 6427.080198] [<fd833208>] ieee80211_do_stop+0x288/0x620 [mac80211]
[ 6427.080243] [<fd8335b7>] ieee80211_stop+0x17/0x20 [mac80211]
[ 6427.080250] [<c148dac1>] __dev_close_many+0x81/0xd0
[ 6427.080270] [<c148db3d>] __dev_close+0x2d/0x50
[ 6427.080276] [<c148d152>] __dev_change_flags+0x82/0x150
[ 6427.080282] [<c148e3e3>] dev_change_flags+0x23/0x60
[ 6427.080289] [<c14f6320>] devinet_ioctl+0x6a0/0x770
[ 6427.080296] [<c14f8705>] inet_ioctl+0x95/0xb0
[ 6427.080304] [<c147a0f0>] sock_ioctl+0x70/0x270
Cc: stable@vger.kernel.org
Reported-by: Antonio Quartulli <ordex@autistici.org>
Tested-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When BT traffic load changes from its
previous state, a new LQ command needs to be
sent down to the firmware. This needs to
be done only once per change. The state
variable that keeps track of this change is
last_bt_traffic_load. However, it was not
being updated when the change had been
handled. Not updating this variable was
causing a flood of advanced BT config
commands to be sent to the firmware. Fix
this.
Cc: stable@vger.kernel.org #2.6.38+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
Pull USB 3.5-rc1 changes from Greg Kroah-Hartman:
"Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as
well. We deleted a staging driver, which was nice, and finally
dropped the obsolete usbfs code, which will make Al happy to never
have to touch that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were
due to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (477 commits)
xhci: Fix DIV_ROUND_UP compile error.
xhci: Fix compile with CONFIG_USB_SUSPEND=n
USB: Fix core compile with CONFIG_USB_SUSPEND=n
brcm80211: Fix compile error for .disable_hub_initiated_lpm.
Revert "USB: EHCI: work around bug in the Philips ISP1562 controller"
MAINTAINERS: Add myself as maintainer to the USB PHY Layer
USB: EHCI: fix command register configuration lost problem
USB: Remove races in devio.c
USB: ehci-platform: remove update_device
USB: Disable hub-initiated LPM for comms devices.
xhci: Add Intel U1/U2 timeout policy.
xhci: Add infrastructure for host-specific LPM policies.
USB: Add macros for interrupt endpoint types.
xhci: Reserve one command for USB3 LPM disable.
xhci: Some Evaluate Context commands must succeed.
USB: Disable USB 3.0 LPM in critical sections.
USB: Add support to enable/disable USB3 link states.
USB: Allow drivers to disable hub-initiated LPM.
USB: Calculate USB 3.0 exit latencies for LPM.
USB: Refactor code to set LPM support flag.
...
Conflicts:
arch/arm/mach-exynos/mach-nuri.c
arch/arm/mach-exynos/mach-universal_c210.c
drivers/net/wireless/ath/ath6kl/usb.c
As iwlwifi use fat skbs, it should not pull too much data in skb->head,
and particularly no tcp data payload, or splice() is slower, and TCP
coalescing is disabled. Copying payload to userland also involves at
least two copies (part from header, part from fragment)
Each layer will pull its header from the fragment as needed.
(on 64bit arches, skb_tailroom(skb) at this point is 192 bytes)
With this patch applied, I have a major reduction of collapsed/pruned
TCP packets, a nice increase of TCPRcvCoalesce counter, and overall
better Internet User experience.
Small packets are still using a fragless skb, so that page can be reused
by the driver.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
