Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix log messages and corrects some typos
Change logging of failure to enable MSI/MSI-X to display device's PCI
address instead of eth%d. Rectify a typo.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix transport header size
Fix the transpoert header size for UDP packets.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently shown that vmxnet3 devices on transmit, will drop very small udp
frames consistently. This is due to a regression introduced by commit
39d4a96fd7. This commit attempts to introduce an
optimization to the tx path, indicating that the underlying hardware behaves
optimally when at least 54 bytes of header data are available for direct access.
This causes problems however, if the entire frame is less than 54 bytes long.
The subsequent pskb_may_pull in vmxnet3_parse_and_copy_hdr fails, causing an
error return code, which leads to vmxnet3_tq_xmit dropping the frame.
Fix it by placing a cap on the copy length. For frames longer than 54 bytes, we
do the pull as we normally would. If the frame is shorter than that, copy the
whole frame, but no more. This ensures that we still get the optimization for
qualifying frames, but don't do any damange for frames that are too short.
Also, since I'm unable to do this, it wuold be great if vmware could follow up
this patch with some additional code commentary as to why 54 bytes is an optimal
pull length for a virtual NIC driver. The comment that introduced this was
vague on that. Thanks!
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Max Matveev <mmatveev@redhat.com>
CC: Max Matveev <mmatveev@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct spelling in "uncommited" to "uncommitted" in
drivers/net/vmxnet3/vmxnet3_drv.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All tables of function pointers should be const to make hacks
more difficult. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers that support modification of the RX flow hash indirection
table initialise it in the same way: RX rings are assigned to table
entries in rotation. Make that default policy explicit by having them
call a ethtool_rxfh_indir_default() function.
In the ethtool core, add support for a zero size value for
ETHTOOL_SRXFHINDIR, which resets the table to this default.
Partly-suggested-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new ethtool operation (get_rxfh_indir_size) to get the
indirectional table size. Use this to validate the user buffer size
before calling get_rxfh_indir or set_rxfh_indir. Use get_rxnfc to get
the number of RX rings, and validate the contents of the new
indirection table before calling set_rxfh_indir. Remove this
validation from drivers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.
Add note that drivers must not use ethtool_rxnfc::rule_locs.
The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vmxnet3 driver enables vlan filters if filtering is enabled for
any vlan. In promiscuous mode the filter table is cleared to in
order to disable filtering. However, if a vlan device is subsequently
created that vlan will be added to the filter, re-engaging it. As a
result, not only do we not see all the vlans in promiscuous mode, we
don't even see vlans for which a filter was previously created.
CC: Scott J. Goldman <scottjg@vmware.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
