The leds timer trigger does not currently have an interface to activate a
one shot timer. The current support allows for setting two timers, one
for specifying how long a state to be on, and the second for how long the
state to be off. The delay_on value specifies the time period an LED
should stay in on state, followed by a delay_off value that specifies how
long the LED should stay in off state. The on and off cycle repeats until
the trigger gets deactivated. There is no provision for one time
activation to implement features that require an on or off state to be
held just once and then stay in the original state forever.
Without one shot timer interface, user space can still use timer trigger
to set a timer to hold a state, however when user space application
crashes or goes away without deactivating the timer, the hardware will be
left in that state permanently.
As a specific example of this use-case, let's look at vibrate feature on
phones. Vibrate function on phones is implemented using PWM pins on SoC
or PMIC. There is a need to activate one shot timer to control the
vibrate feature, to prevent user space crashes leaving the phone in
vibrate mode permanently causing the battery to drain.
This trigger exports three properties, activate, state, and duration When
transient trigger is activated these properties are set to default values.
- duration allows setting timer value in msecs. The initial value is 0.
- activate allows activating and deactivating the timer specified by
duration as needed. The initial and default value is 0. This will allow
duration to be set after trigger activation.
- state allows user to specify a transient state to be held for the specified
duration.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: NeilBrown <neilb@suse.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson:
"These changes are all specific to one board only. We're trying to
keep the number of board files low, but generally board level updates
are ok on platforms that are working on moving towards DT based
probing, which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal
of ams_delta_config and the addition of a lot of other data. The
Kconfig file has two changes in the same line, and in exynos, the
power domain cleanup conflicts with the addition of the image sensor
device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>"
Fixed up some fairly trivial conflicts manually.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits)
i.MX35-PDK: Add Camera support
ARM : mx35: 3ds-board: add framebuffer device
pxa/hx4700: Remove pcmcia platform_device structure
ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%
ARM: pxa/hx4700: Remove unwanted request for GPIO105
ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board
ARM: EXYNOS: Register JPEG on nuri
ARM: EXYNOS: Register JPEG on universal_c210
ARM: S5PV210: Enable JPEG on SMDKV210
ARM: S5PV210: Add JPEG board definition
ARM: EXYNOS: Enable JPEG on Origen
ARM: EXYNOS: Enable JPEG on SMDKV310
ARM: EXYNOS: Add __init attribute to universal_camera_init()
ARM: EXYNOS: Add __init attribute to nuri_camera_init()
ARM: S5PV210: Enable FIMC on SMDKC110
ARM: S5PV210: Enable FIMC on SMDKV210
ARM: S5PV210: Enable MFC on SMDKC110
ARM: S5PV210: Enable MFC on SMDKV210
ARM: EXYNOS: Enable G2D on SMDKV310
ARM: tegra: update defconfig
...
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
* 'omap1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
input: serio: ams-delta: toggle keyboard power over GPIO
omapfb: lcd_ams_delta: drive control lines over GPIO
MTD: NAND: ams-delta: use GPIO instead of custom I/O
LED: drop leds-ams-delta driver
ARM: OMAP1: ams-delta: supersede custom led device by leds-gpio
ARM: OMAP1: ams-delta: convert latches to basic_mmio_gpio
ARM: OMAP1: ams-delta: register latch dependent devices later
Add support for leds on Bachmann's ot200 visualisation device. The
device has three leds on the back panel (led_err, led_init and led_run)
and can handle up to seven leds on the front panel.
The driver was written by Linutronix on behalf of Bachmann electronic
GmbH. It incorporates feedback from Lars-Peter Clausen
[akpm@linux-foundation.org: add dependency on HAS_IOMEM]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
TI's TCA6507 is the LED driver in the GTA04 Openmoko motherboard. The
driver provides full support for brightness levels and hardware blinking.
This driver can drive each of 7 outputs as an LED or a GPIO output,
and provides hardware-assist blinking.
[akpm@linux-foundation.org: fix __mod_i2c_device_table alias]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver is no longer needed after the Amstrad Delta on-board LED
devices have been converted to leds-gpio compatible.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add V2 of the LED driver for a single timer channel for the TPU hardware
block commonly found in Renesas SoCs.
The driver has been written with optimal Power Management in mind, so to
save power the LED is driven as a regular GPIO pin in case of maximum
brightness and power off which allows the TPU hardware to be idle and
which in turn allows the clocks to be stopped and the power domain to be
turned off transparently.
Any other brightness level requires use of the TPU hardware in PWM mode.
TPU hardware device clocks and power are managed through Runtime PM.
System suspend and resume is known to be working - during suspend the LED
is set to off by the generic LED code.
The TPU hardware timer is equipeed with a 16-bit counter together with an
up-to-divide-by-64 prescaler which makes the hardware suitable for
brightness control. Hardware blink is unsupported.
The LED PWM waveform has been verified with a Fluke 123 Scope meter on a
sh7372 Mackerel board. Tested with experimental sh7372 A3SP power domain
patches. Platform device bind/unbind tested ok.
V2 has been tested on the DS2 LED of the sh73a0-based AG5EVM.
[axel.lin@gmail.com: include linux/module.h]
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This new driver replaces the old PCEngines Alix 2/3 LED driver with a
new driver that controls the LEDs through the leds-gpio driver. The
old driver accessed GPIOs directly, which created a conflict and
prevented also loading the cs5535-gpio driver to read other GPIOs on
the Alix board. With this new driver, we hook into leds-gpio which in
turn uses GPIO to control the LEDs and therefore it's possible to
control both the LEDs and access onboard GPIOs
Driver is moved to platform/geode as requested by Grant and any other
geode initialisation modules should move here also
This driver is inspired by leds-net5501.c by Alessandro Zummo.
Ideally, leds-net5501.c should also be moved to platform/geode.
Additionally the driver relies on parts of the patch: 7f131cf3ed ("leds:
leds-alix2c - take port address from MSR) by Daniel Mack to perform
detection of the Alix board.
[akpm@linux-foundation.org: include module.h]
Signed-off-by: Ed Wildgoose <kernel@wildgooses.com>
Cc: git@wildgooses.com
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We call led_classdev_register/led_classdev_unregister in
create_netxbig_led/delete_netxbig_led, thus make LEDS_NETXBIG depend on
LEDS_CLASS.
This patch fixes below build error if LEDS_CLASS is not configured.
LD .tmp_vmlinux1
drivers/built-in.o: In function `create_netxbig_led':
drivers/leds/leds-netxbig.c:350: undefined reference to `led_classdev_register'
drivers/leds/leds-netxbig.c:361: undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `delete_netxbig_led':
drivers/leds/leds-netxbig.c:313: undefined reference to `led_classdev_unregister'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
