Add support for UC-Logic Wireless Tablet TWHL850.
It is known to be sold as Genius MousePen M508W.
This tablet has a bug in the default (compatibility) mode which is used in this
driver: frame button assignments are mixed up. This is to be fixed with a driver
supporting the vendor-specific protocol.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Put a comment that clarifies the condition that handles both signed
and unsigned case for logical min/max in hid_add_field().
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When logical maximum is 0xffffffff, the parser fails even if
logical minimum is more than 0.
By HID specification this is a valid combination.
Signed-off-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I am merging multitouch branch into device-groups so that support
for Baanto device can be adjusted accordingly to the new autoloading
patches.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Switch the driver over to device group handling. By adding the
HID_GROUP_MULTITOUCH group to hid-core, hid-generic will no longer
match multitouch devices. By adding the HID_GROUP_MULTITOUCH entry to
the device list, hid-multitouch will match all unknown multitouch
devices, and udev will automatically load the module.
Since HID_QUIRK_MULTITOUCH never gets set, the special quirks handling
can be removed. Since all HID MT devices have HID_DG_CONTACTID, they
can be removed from the hid_have_special_driver list.
With this patch, the unknown device ids are no longer NULL, so the code
is modified to check for the generic entry instead.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices that do not have a special driver are handled by the generic
driver. This patch does the same thing using device groups; Instead of
forcing a particular driver, the appropriate driver is picked up by
udev. As a consequence, one can now move a device from generic to
specific handling by a simple rebind. By adding a new device id to the
generic driver, the same thing can be done in reverse.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Most HID drivers do not need to know what bus driver is in use.
A generic group driver can drive any hid device, and the device
list should not need to be duplicated for each new bus.
This patch adds wildcard matching to the HID bus, simplifying device
list handling for group drivers.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In order to allow the report descriptor to influence the hid device
properties, one needs to parse the descriptor early, without reference
to any driver. Scan the descriptor for group information during device
add, before the device has been broadcast to userland. The device
modalias will contain group information which can be used to
differentiate between modules. For starters, just handle the generic
group.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID devices are only partially presented to userland. Hotplugged
devices emit events containing a modalias based on the basic bus,
vendor and product entities. However, in practise a hid device can
depend on details such as a single usb interface or a particular item
in a report descriptor.
This patch adds a device group to the hid device id, and broadcasts it
using uevent and the device modalias. The module alias generation is
modified to match. As a consequence, a device with a non-zero group
will be processed by the corresponding group driver instead of by the
generic hid driver.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The low-level driver can read the report descriptor, but it cannot
determine driver-specific changes to it. The hid core can fixup
and parse the report descriptor during driver attach, but does
not have direct access to the descriptor when doing so.
To be able to handle attach/detach of hid drivers properly,
a semantic change to hid_parse_report() is needed. This function has
been used in two ways, both as descriptor reader in the ll drivers and
as a parsor in the probe of the drivers. This patch splits the usage
by introducing hid_open_report(), and modifies the hid_parse() macro
to call hid_open_report() instead. The only usage of hid_parse_report()
is then to read and store the device descriptor. As a consequence, we
can handle the report fixups automatically inside the hid core.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Nikolai Kondrashov <spbnick@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If kmemdup() in hidraw_report_event() fails, we are not propagating
this fact properly.
Let hidraw_report_event() and hid_report_raw_event() return an error
value to the caller.
Reported-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices like Aureal Cy se W-01RN USB_V3.1 and some derived hardware
have a bogus HID Report Descriptor. According to that report descriptor,
the maximum logical value for key events is 1 and not 101 (101 keys).
This quirk fixes this wrong Report Descriptor.
Signed-off-by: Josenivaldo Benito Junior <jrbenito@benito.qsl.br>
Signed-off-by: Franco Catrin <fcatrin@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for Waltop Sirius Battery Free Tablet. VisTablet Muse and Princeton
PTB-S1BK are other possible names of this tablet.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull media updates from Mauro Carvalho Chehab:
- V4L2 API additions to better support JPEG compression control
- media API additions to properly support MPEG decoders
- V4L2 API additions for image crop/scaling
- a few other V4L2 API DocBook fixes/improvements
- two new DVB frontend drivers: m88rs2000 and rtl2830
- two new DVB drivers: az6007 and rtl28xxu
- a framework for ISA drivers, that removed lots of common code found
at the ISA radio drivers
- a new FM transmitter driver (radio-keene)
- a GPIO-based IR receiver driver
- a new sensor driver: mt9m032
- some new video drivers: adv7183, blackfin, mx2_emmaprp, sii9234_drv,
vs6624
- several new board additions, driver fixes, improvements and cleanups.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (295 commits)
[media] update CARDLIST.em28xx
[media] partially reverts changeset fa5527c
[media] stb0899: fix the limits for signal strength values
[media] em28xx: support for 2304:0242 PCTV QuatroStick (510e)
[media] em28xx: support for 2013:0251 PCTV QuatroStick nano (520e)
[media] -EINVAL -> -ENOTTY
[media] gspca - sn9c20x: Cleanup source
[media] gspca - sn9c20x: Simplify register write for capture start/stop
[media] gspca - sn9c20x: Add automatic JPEG compression mechanism
[media] gspca - sn9c20x: Greater delay in case of sensor no response
[media] gspca - sn9c20x: Optimize the code of write sequences
[media] gspca - sn9c20x: Add the JPEG compression quality control
[media] gspca - sn9c20x: Add a delay after Omnivision sensor reset
[media] gspca - sn9c20x: Propagate USB errors to higher level
[media] gspca - sn9c20x: Use the new video control mechanism
[media] gspca - sn9c20x: Fix loss of frame start
[media] gspca - zc3xx: Lack of register 08 value for sensor cs2102k
[media] gspca - ov534_9: Add brightness to OmniVision 5621 sensor
[media] gspca - zc3xx: Add V4L2_CID_JPEG_COMPRESSION_QUALITY control support
[media] pvrusb2: fix 7MHz & 8MHz DVB-T tuner support for HVR1900 rev D1F5
...
Pull input subsystem updates from Dmitry Torokhov:
"- we finally merged driver for USB version of Synaptics touchpads
(I guess most commonly found in IBM/Lenovo keyboard/touchpad combo);
- a bunch of new drivers for embedded platforms (Cypress
touchscreens, DA9052 OnKey, MAX8997-haptic, Ilitek ILI210x
touchscreens, TI touchscreen);
- input core allows clients to specify desired clock source for
timestamps on input events (EVIOCSCLOCKID ioctl);
- input core allows querying state of all MT slots for given event
code via EVIOCGMTSLOTS ioctl;
- various driver fixes and improvements."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: ili210x - add support for Ilitek ILI210x based touchscreens
Input: altera_ps2 - use of_match_ptr()
Input: synaptics_usb - switch to module_usb_driver()
Input: convert I2C drivers to use module_i2c_driver()
Input: convert SPI drivers to use module_spi_driver()
Input: omap4-keypad - move platform_data to <linux/platform_data>
Input: kxtj9 - who_am_i check value and initial data rate fixes
Input: add driver support for MAX8997-haptic
Input: tegra-kbc - revise device tree support
Input: of_keymap - add device tree bindings for simple key matrices
Input: wacom - fix physical size calculation for 3rd-gen Bamboo
Input: twl4030-vibra - really switch from #if to #ifdef
Input: hp680_ts_input - ensure arguments to request_irq and free_irq are compatible
Input: max8925_onkey - avoid accessing input device too early
Input: max8925_onkey - allow to be used as a wakeup source
Input: atmel-wm97xx - convert to dev_pm_ops
Input: atmel-wm97xx - set driver owner
Input: add cyttsp touchscreen maintainer entry
Input: cyttsp - remove useless checks in cyttsp_probe()
Input: usbtouchscreen - add support for Data Modul EasyTouch TP 72037
...
Pull HID updates from Jiri Kosina:
"It contains HID driver updates all over the place -- a lot of new
hardware support especially in the multitouch area, including generic
handling of all multitouch devices by the hid-multitiouch driver
automatically."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (42 commits)
HID: multitouch: add PID for Fructel product
HID: wacom: Add reporting of wheel for Intuos4 WL
HID: wacom: Replace __set_bit with input_set_capability
HID: tivo: add support for BT-version (0x1200)
HID: wacom: Reset stylus buttons - Intuos4 WL
HID: multitouch: detect serial protocol
HID: handle all multitouch devices through hid-multitouch
HID: multitouch: fix handling of buggy reports descriptors for Dell ST2220T
HID: make it possible to force hid-core claim the device
HID: multitouch: add support for eGalax 0x722a
HID: usbhid: add quirk no_get for quanta 3008 devices
HID: multitouch: add more eGalax devices
HID: multitouch: add new PID from Ideacom
HID: multitouch: add support for Atmel maXTouch 03eb:2118
HID: waltop: Add support for tablet with PID 0038
HID: waltop: Replace original rdescs with links
HID: uclogic: Replace original rdescs with links
HID: wacom: Add pad buttons reporting on Intuos4 WL
HID: wacom: report distance for Intuos4 WL
HID: kye: Add support for 3 tablets
...
Adds multitouch support for the Gametel Android game controller.
The multitouch events are emulated by the Gametel device. Each physical button
is configured to generate a MT event on a specific coordinate. This seems to be
the only way for us to support Android games that doesn't support HID gamepads.
It is possible to inject MT events at Android level, but this requires root on
the phone.
Signed-off-by: Andreas Nielsen <eas@svep.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for BT-driven configuration of the TiVo remote.
Reported-by: Joshua Dillon <jvdillon@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When the quirk HID_QUIRK_MULTITOUCH is present and when hid-multitouch
is loaded, let's pass the device to hid-multitouch even if it has
not been registered in hid-multitouch.
If any other driver wants to take precedence over hid-multitouch,
the usual way of adding it to hid_have_special_driver will work as
the quirk HID_QUIRK_MULTITOUCH won't be set by the generic hid layer.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Introduce 'hid_ignore_special_drivers' module parameter that makes hid-core
claim the device even if it's listed in hid_have_special_driver[]. This
is useful mostly for debugging purposes and specialized initrds, where
all the hid drivers are not avaiable.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
